Related Manuals for Christie MIRAGE WU20K-J
Summary of Contents for Christie MIRAGE WU20K-J
- Page 1 Mirage J Series U s e r M a n u a l 020-100708-01 Downloaded From projector-manual.com Christie Manuals...
- Page 2 Downloaded From projector-manual.com Christie Manuals...
- Page 3 Mirage J Series U s e r M a n u a l 020-100708-01 Downloaded From projector-manual.com Christie Manuals...
- Page 4 Projector lamps (See Christie separate lamp program policy). c. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp supplied by a supplier other than Christie. d. Problems caused by combination of the product with non-Christie equipment, such as distribution systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface device.
- Page 5 Table of Contents 1: Introduction 1.1 Projector Overview........................1-1 2: Operation 2.1 3D ..............................2-1 A: Menu Tree A.1 Mirage J Series Menu Tree......................A-1 B: GPIO B.1 GPIO Port............................B-1 Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 6 Downloaded From projector-manual.com Christie Manuals...
-
Page 7: Projector Overview
132-006129- IRAGE S+14K-J 132-010124- IRAGE HD14K-J 132-011125- IRAGE WU14K-J 132-012126- IRAGE S+18K-J 132-013127- IRAGE HD16K-J 132-014128- IRAGE S+22K-J 132-016120- IRAGE HD20K-J 132-017121- IRAGE WU20K-J 132-018122- IRAGE Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals... - Page 8 Downloaded From projector-manual.com Christie Manuals...
- Page 9 • Christie 3D version of Mirage J Series projector. • Christie 3D Stereo Sync Cable (required for 3D Mirage J Series models; ensures minimum frame delay). This General Purpose Input Output (GPIO) cable is standard with all Mirage J Series projectors. NOTE: See Appendix B: GPIO.
- Page 10 3D passive filter system, PZE device. The L/R switching of the device can then be synchronized according to the controlling signal of choice—either the source input signal or the internally generated signal—as set in the 3D Settings menu. Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 11 This separate signal is usually provided using a VESA 3 pin stereo port. Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 12 3D State: Informs you what state the projector is in: Off, Missing Secondary Signal, Not Frame Locked, Secondary Frequency Mismatch, High Bandwidth Not Supported, Stereo Sync Not Detected, Stereo Sync Invalid, and Invalid Frequency. This is read only. NOTE: Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 13 6-9 to swap the eyes). NOTE: This function is not used in Interleaved 3D mode. Each eye FUNC receives a selected input and no 3D sync input is required. Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 14 Secondary Input: Select an input to be used as secondary input in a Dual Input 3D setup. Display 3D Message Boxes: Enable/Disable message boxes that are triggered by 3D setup. NOTE: message box is shown in “Off” and “Valid” state. Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 15 NOTE: The default auto setup value is typically good for all glasses. 16. Turn off the 3D test pattern on each projector. Your 3D content should look optimal. Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 16 Section 3: Operation 2-3 E 3D M IGURE XAMPLE OF ULTIPLE ISPLAY ETUP Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 17 Appendix A: Menu Tree A.1 Mirage J Series Menu Tree Mirage J Series User Manual 020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 18 Downloaded From projector-manual.com Christie Manuals...
- Page 19 Appendix A: Menu Tree Mirage J Series User Manual 020-100708-01 Rev.1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 20 Appendix A: Menu Tree Mirage J Series User Manual 020-100708-01 Rev.1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 21 Appendix A: Menu Tree Mirage J Series User Manual 020-100708-01 Rev.1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 22 Downloaded From projector-manual.com Christie Manuals...
- Page 23 Pin 9 GPIO 7 The serial cable required for connecting the external device to the GPIO connector of the projector, must be compatible with the external device. Mirage J Series User Manual -020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 24 Inputs, pins 6, 7, 8 & 9 are Outputs The strings in the commands refer to pins 2, 3, 4, 6, 7, 8, 9 in order from left to right. NOTE: Mirage J Series User Manual -020-100708-01 Rev. 1 (11-2011) Downloaded From projector-manual.com Christie Manuals...
- Page 25 Downloaded From projector-manual.com Christie Manuals...
- Page 26 +86 10 6561 0240 ph: +82 2 702 1601 Germany Spain Shanghai ph: +49 2161 664540 ph: + 34 91 633 9990 ph: +86 21 6278 7708 For the most current technical documentation, please visit www.christiedigital.com Downloaded From projector-manual.com Christie Manuals...