Technical Specifications - Bose PS602 Installation And Operating Manual

pro.Bose.com
PS602, PS602P, and PS604 Technical Specifications
Power Rating
Amplifier Power
1
Maximum Power per Channel
Gain (Low-Z mode)
Gain (70V mode)
Gain (100V mode)
All channels driven, THD+N < 0.04%, 1 kHz, 4-8 Ω, 70/100V
1
Audio Performance
Frequency Response
Channel Separation
(Crosstalk)
Signal to Noise Ratio
Audio Inputs
Input Channels
Connectors
Input Impedance
Maximum Input Level
Sensitivity
Audio Outputs
Outputs
Connectors
Integrated DSP
A/D and D/A Converters
Processing Functions
Loudspeaker Presets
Audio Latency
Indicators and Controls
Power LED
Input Signal LED
Output Limit LED
Controls, Front Panel
Controls, Rear Panel
Electrical
Mains Voltage
AC Power Consumption
Mains Connector
Maximum Inrush Current
Protections
Physical
Dimensions
Shipping Weight
Net Weight
Cooling System
General
Inputs (Control)
Installation Guide
PS602
2 x 300 W
600 W @ 4-8 Ω, 70/100V
44 dB, RCA (unbalanced) inputs; 32 dB, Euroblock (balanced) inputs
47 dB, RCA (unbalanced) inputs; 35 dB, Euroblock (balanced) inputs
50 dB RCA (unbalanced) inputs; 38 dB, Euroblock (balanced) inputs
4-8 Ω: 20 Hz – 20 kHz (+/- 0.5 dB, @ 1 W)
70/100V: Same as 4-8 Ω with 50 Hz high-pass filter
> 85 dB @ 1 kHz, > 65 dB @ 20 kHz
100 dB (at rated power, A-weighted)
PS602
2 unbalanced, 2 balanced
Stereo RCA, 3-pin Euroblock
10 kΩ (RCA), 20 kΩ (Euroblock, XLR/TRS)
20 dBu (at 12 dBu sensitivity setting)
-10 / -2 dBu, RCA inputs; 4 / 12 dBu, Euroblock inputs (low / high sensitivity)
PS602
2
2-pin inverted Euroblock
24-bit / 48 kHz
Standard mixer, loudspeaker EQ, 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity
inversion
Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105 and RMU108
1 ms (any input to speaker output)
Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault. Solid red: Supply
fault.
Green: Signal present. Amber: Input is near clipping. Red: Input is clipping. Solid red: Indicates a fault.
Amber: Amplifier limiting an output. Blinking red: Amplifier muted from rear panel. Solid red: Indicates a fault.
Power On/Off, Output Level Control (PS602P only)
Amplifier mode DIP switches, loudspeaker EQ dials, output attenuators (PS602 and PS604 only)
100 VAC – 240 VAC (±10%, 50/60 Hz)
120 VAC: 79 W (Standby), 124 W (Max)
Standard IEC (C14)
14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)
High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage
44 mm H x 483 mm W x 414 mm D (1.7" H x 19.0" W x 16.3" D)
PS602 and PS602P: 6.9 kg (15.3 lb); PS604: 7.8 kg (17.2 lb)
PS602 and PS602P: 5.5 kg (12.2 lb); PS604: 6.4 kg (14.1 lb)
Microprocessor controlled, variable speed fans, left to right air flow
RJ-45 remote input for volume control using the CC-1 ControlCenter zone controllers (PS602 and PS604 only),
or for connection to the CV41. USB input for configuring the amplifier with PowerShare Editor software. Mute
input control.
PS602P
2 x 300 W
600 W @ 4-8 Ω, 70/100V
PS602P
2 unbalanced, 2 balanced
Stereo RCA, XLR/TRS
PS602P
2
NL4 & binding posts
230 VAC: 88 W (Standby), 184 W (Max)
Technical Information
PS604
4 x 150 W
600 W @ 4-8 Ω, 70/100V
PS604
4 balanced
12-pin Euroblock
PS604
4
8-pin inverted Euroblock
English 33