F F L L A A S S H H D D I I F F F F U U S S E E R R; A A R R M M S S Y Y S S T T E E M M S S / / S S T T R R O O B B E E M M O O U U N N T T S; Batt Ttl; W/Lite -1 - Ikelite DS160 Instructions Manual

F F L L A A S S H H D D I I F F F F U U S S E E R R # # 0 0 5 5 9 9 1 1 . . 3 3

U U S S I I N N G G T T H H E E D D I I F F F F U U S S E E R R
The white diffuser can be secured to the front of the DS1 60 strobe when softer lighting
or a coverage angle of 1 00° is desired.
The diffuser reduces the DS1 60's light intensity by one full f-stop.
D D I I F F F F U U S S E E R R I I N N S S T T A A L L L L A A T T I I O O N N A A N N D D R R E E M M O O V V A A L L
1 . Position the Diffuser Cut-outs over the DS1 60 strobe's Diffuser Retention Tabs.
2. Press down lightly until the diffuser is flush against the strobe face.
3. Rotate the Diffuser Installation Posts either direction until the Posts stop against the
strobe's Diffuser Retention Tabs.
4. Reverse process to remove the Diffuser.
- A lanyard or string can be attached to the diffuser by threading it through the two
Lanyard Holes near its edge. Attach the other end to the strobe to prevent
accidental loss.
F F l l a a s s h h D D i i f f f f u u s s e e r r
Installation Post
Diffuser
Lanyard Holes
Cut-outs
D D S S 1 1 6 6 0 0 S S t t r r o o b b e e
Diffuser Retention Tab
9
A A R R M M S S Y Y S S T T E E M M S S / / S S T T R R O O B B E E M M O O U U N N T T S S
I I K K E E L L I I T T E E A A R R M M S S Y Y S S T T E E M M S S
Ikelite offers several arm choices compatible with the DS1 60. The arm and strobe mount
are NOT supplied with the strobe unless purchased as part of a complete package. For
additional information go to www.ikelite.com
C C a a u u t t i i o o n n : : Ikelite arm systems are designed for underwater use. Be careful when
transporting the system above water since some camera trays and arm adjustments may
be unable to support the weight of the strobe(s) above water.
I I K K E E L L I I T T E E M M O O U U N N T T S S
An optional paddle-type or ball-type mount can be mounted to the underneath side of
the strobe. The mount slides into the strobe base and is secured with a screw (supplied
with optional mount). Make sure to slide the mount into the strobe base until it stops.
Be careful to not cross-thread the screw when tightening the mount. The DS1 60 Shroud
can be rotated slightly to gain better access to the strobe base with a screwdriver.
Although not necessary, you can apply a small amount of Ikelite lube around the screw
threads before attaching the strobe mount. Use Ikelite lube only which is supplied with
the DS1 61 strobe. This will reduce the possibility of seizing and allow removal of the
screw should the mount need to be removed. Removing the mount for long storage
periods will also reduce the possibility of seizing.
Batt
w/Lite
Off
On
On
w/Lite
Strobe Base
Ball-Type Mount
"not included"
with DS1 60

Fuel

TTL

Gauge

Full
-1
3
-2

Ready Light

2
-3
-4
1
1
DS1 60 Shroud
Mount Screw
10