Remington HC5950 Owner's Manual page 4

ENGLISH
A CAUTION
If the incorrect comb is attached to the product for the desired cutting length, a red warning
light will illuminate to indicate this.
Please inspect that the desired comb is attached or that the correct setting is selected on the
comb switch.
F INSTRUCTIONS FOR HAIR CUTTING
Note: For even cutting, allow the comb attachment/blade to cut its way through the hair. Do
not force it through quickly. If you are cutting for the first time, start with the maximum comb
attachment
STEP 1 – Nape of the neck
• Set the comb to 3mm or 6mm.
• Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre of
the head at the base of the neck.
• Slowly lift the clipper, working upwards and outwards through the hair, trimming just a
little at a time
STEP 2 – Back of the head
With the comb set at 12mm or 18mm, cut the hair at the back of the head.
STEP 3 – Side of the head
• Set the comb to 3mm or 6mm, trim sideburns. Then change the setting to 9mm and
continue to cut the top of the head.
STEP 4 – Top of the head
• Use the longer length comb attachment and set it to 24mm or 27mm then cut hair on
top of the head against the direction in which the hair normally grows.
• For longer hair on top, use the longer length comb attachment (22 – 42mm) to achieve
the desired style.
• Always work from the back of the head.
STEP 5 – The finishing touches
• Use the clipper without an attachment comb for close trimming around the base and
sides of the neck.
• To produce a clean straight line at the sideburns, reverse the hair clipper. Place the
reversed clipper at right angles to the head, tips of the blades lightly touching the skin
and then work downwards.
, SHORT TAPERED STYLES – "FLAT TOPS" & SHORT CUTS
• Starting with the longest guide comb attached (22 - 42mm), cut from the back of the
neck to the crown. Hold the guide comb flat against the head and slowly move the
clipper through the hair.
• Use the same procedure from the lower side to the upper side of the head. Then cut the
hair against the direction in which it grows and level with the sides.
• To give a "flat top" look, the hair on top of the head must be cut over the top of a flat
comb.
6
ENGLISH
• Use a closer guide comb to taper the hair down to the neckline as desired.
C CARE FOR YOUR HAIRCLIPPER
Your clipper is fitted with high quality titanium blades that are permanently lubricated.
To ensure long lasting performance of your clipper, clean the blades and unit regularly.
Always keep the attachment guide comb on the trimmer blade.
E
AFTER EACH USE
• Ensure the clipper is switched off and disconnected from the mains.
• Remove attachment guide comb and cutter assembly.
• Gently brush the remaining hairs away from the comb and trimmer blade.
• Do not rinse the cutter assembly under water.
F RESET INSTRUCTIONS
• Hold the power button for 8 consecutive seconds
• System will show 88.8mm, full battery, full lock and full boost level.
• Ensure no objects, hands or fingers are near the touch buttons.
• Push the power button once.
• Comb will travel down to its lowest setting, and display will show current battery level,
lock status and 1st boost level.
• Let the product sit until the screen dims.
• Product is now ready, turn it on and confirm proper function.
A CLEANING CAUTIONS
• Only the attachment guide combs and trimmer blade may be removed from the
product for cleaning.
• Cleaning should be done with a soft brush, such as the brush supplied with the product.
• The appliance is not washable.
• Do not rinse under water.
• Do not use harsh or corrosive cleaners on the units or their blades
F IMPORTANT SAFETY INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR INJURY TO
PERSONS:
• An appliance should never be left unattended when plugged in to a power outlet,
except when charging.
• Keep the power plug and cord away from heated surfaces.
• Make sure the power plug and cord do not get wet.
7