Weider 140 User Manual page 8

7. Tap a 1 1/2" Square Inner Cap (30) into the indi-
cated end of the Left Arm (43). Tap a 7/8" Round
Inner Cap (35) into the indicated hole in the Left
Arm.
Attach an 11" Weight Tube (39) to the Left Arm
(43) with a 5/16" x 5" Bolt (32), a 1/2" x 3" Plastic
Spacer (36) and a 5/16" Nylon Locknut (19).
Tap a 1" Round Inner Cap (24) into the indicated
end of the 11" Weight Tube (39). Slide a Weight
Stop (38) onto the Weight Tube.
Assemble the Right Arm (42) in the same manner.
8. Tap a Flanged Plastic Sleeve (37) into the tube
on the indicated side of the "H"-Frame (1).
Lubricate the axle on the Left Arm (43). Insert the
axle through the tube and the Flanged Plastic
Sleeve. Make sure that the 1/2" x 3" Plastic
Spacer (36) is resting against the outside of
the "H"-Frame (1). Insert a Spring Clip (34) into
the axle. Make sure that the Spring Clip snaps
into the hole near the end of the axle.
Attach the Right Arm (42) in the same manner.
9. Attach a 9" Pad Tube (40) to the Left Arm (43)
with a 1/4" x 2" Screw (33) and a 1/4" Nylon
Locknut (28). Tap a 3/4" Round Inner Cap (26)
into the indicated end of the 9" Pad Tube.
Slide a Foam Pad (23) onto the 9" Pad Tube (40).
Repeat this step for the Right Arm (42).
10. Attach the two Backrest Brackets (5) to the
Backrest (6) with four 1/4" x 1/2" Screws (13).
Make sure that the Backrest Brackets and the
Backrest are oriented as shown.
7
36
19
43
35
42
32 39
38
8
42
1
Tube
37
43—Lubricate
36
9
42
43
40
26
23
10
5
6
13
8
11. Press a 3/4" Round Inner Cap (26) into the indi-
cated end of the Support Rod (7). Insert the
Support Rod through one of the four sets of holes
in the "H"-Frame (1). Rotate the Support Rod to
the locked position, with the end of the Support
Rod clipped onto the "H"-Frame.
30 Attach the Backrest Brackets (5) to the Frame (2)
with the 5/16" x 4" Bolt (17), the two 1/2" x 7/8"
Metal Spacers (25), and a 5/16" Nylon Locknut
(19). Rest the Backrest (6) on the Support Rod
24
(7).
12. Attach the Seat (11) to the bracket on the Frame
(2) with two 1/4" x 1/2" Screws (13).
34
13. Attach the Curl Pad (10) to the Curl Post (44) with
two 1/4" x 1/2" Screws (13).
33
28
14. Insert the Curl Post (44) into the Frame (2) as
shown. Align one set of holes in the Curl Post
with the holes in the Frame. Insert the Locking
Pin (8) through the Frame and the Curl Post.
Rotate the Locking Pin to the locked position, with
the Locking Pin clipped onto the Frame.
11
7
1
6
5
19
2
25
17
12
11
2
13
13
10
13
44
14
44
8
2
9
26