Before Operation - Sanyo DC F200 Instruction Manual

BEFORE OPERATION
Turning the power on and off
Press the POWER button on the front panel to ON (button in). The power
turns on and display lights. (After connecting the mains lead, when you
press the POWER button for the first time, the volume reset feature
automatically sets the initial volume level '(VO3.)
To turn off the power, press the POWER button again to b (button out).
Using the remote control
First, press the POWER button (button in) on the front panel. The unit
will respond to commands from the remote control.
To turn the power on and off, press the POWER button on the remote
control.
When the power is turned off by using the remote control, the
STANDBY indicator lights and the unit is in the standby condition.
Selecting the function
Press the FUNCTION button to select the desired function. Each time the
button is pressed, the display changes as follows:
Cd (CD)
TA (Tape)
TU (Tuner)
Vd (Video)
The function is automatically selected when CD play is started or when the
BAND button has been pressed (except during recording or tape dubbing).
- When the function selection is changed, CD play is automatically
stopped.
Adjusting the volume
Press the UP or DOWN VOLUME button, or press the+ or – VOLUME
button on the remote control. The volume level appears on the display (Vo
O-vo lo).
Adjusting the sound quality
Use the TREBLE or MID control to adjust the treble or mid range output
level.
Bass expander system
Use the BASSXPANDER control to adjust the bass output level.
WHAT TO DO IF ...
If the operation of the unit or display is not normal or when all the memory
contents are to be cleared, disconnect the mains lead from the AC outlet,
then press the RESET button (rear of the unit) for 30 seconds or more.
CD PLAY
Use compact discs bearing the symbol shown below. In addition to
conventional 12cm CDS, this system can be used to cday8cm CDs without
an adapter.
ncOMpAcT
mm
DIGITAL AUDIO
Note:
1.
2.
3.
Do not touch the disc tray while it is moving.
Never place anything except a compact disc on the disc tray. Foreign
objects can damage the unit.
Do not apply excessive force to the disc tray.
Discs must be placed on the disc tray one at a time.
Select "CD function by pressing the FUNCTION button. "Cd appears
on the display, then "Cd is replaced by "dlSC. "1" disc number blinks.
Press one of the disc select buttons (DISC 1, DISC 2 or DISC 3), then
press the OPEN/CLOSE button.
If the changer mechanism has detected "no disc" for the disc
select button pressed, the tray slides out automatically.
The selected disc tray slides out. "OPEN" appears and the selected
disc number blinks on the display.
Place the disc with the label facing upon the disc tray.
'@'@
4.
5.
6.
7.
Press the OPEN/CLOSE button again to close the disc tray.
Note:
To open or close the disc tray, be sure to use the OPEN/CLOSE
button, Do not touch the disc tray by hand.
Repeat steps 2-4 to load another disc.
Press one of the disc select buttons (DISC 1, DISC 2 or DISC 3).
32s1
~ TRACK
0.01
C9
D
"D" appears, and play starts from the first track of the selected disc.
The track number and elapsed playing time for the current track are
displayed.
If the desired disc number has been selected, the PLAY/PAUSE
button can also be used to start play.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "NO dlSC appears on the display.
If this occurs, load the disc correctly or replace the damaged disc.
Press the STOP button to end disc play.
When the last track of the last disc has been played, the player stops
automatically.
When the OPEN/CLOSE button is pressed during play, play will stop
and the disc tray will slide out.
For 12 cm CD
For 8 cm CD '
5