Playback Point (Start And End); Repeat Play (Repeat, Repeat Interval) - Roland AR-3000SD Reference Manual

Playback Point (Start and End)

These determine where phrase playback is to start and end.
Playback passage
Phrase
Start
NOTE
You cannot make these settings for MODE2 or MP3 phrases.
Procedure for setting playback point
1.
Use the [SELECT] dial to choose the phrase whose setting
you want to change.
2.
Press the [MENU] button.
The MENU indicator lights up.
3.
Use the [SELECT] dial to choose "1.3 Playback Point," then
press the dial.
You can reselect the phrase whose setting you want to change by
pressing the [BACK] (USER) button. The entry position (highlighted)
moves to the phrase selection, so turn the [SELECT] dial to reselect
card and the phrase number, then press the dial.
4.
Turn the [SELECT] dial to select the start position (time),
then press the dial.
Pressing the dial while the cursor (highlighted) is at the "sf" position
moves the end position setting.
* Each press of the [BACK] (USER) button moves the cursor
(highlighted) in the sequence of sf 0 f 0 s 0 m 0 h.
Pressing the dial while the cursor (highlighted) is at the "sf"
position moves the end position setting.
* The frame display varies according to the setting for the MIDI
Time Code (MTC) frame rate.
Turn the [SELECT] dial to set the end position (time), then press the
dial.
5.
When the prompt appears on the screen, press the
[ENTER] button to enable the settings.
To quit without making the settings, use the [SELECT] dial to
choose "NO, " then press the [ENTER] button.
Once the settings have been successfully modified, you're returned
to the setting item selection screen.
6.
Press the [MENU] button.
This ends the setting process and returns you to the usual screen.
* While making the settings, you can go back to the previous
entry location (highlighted) by pressing the [BACK] (USER)
button.
* If you press the [MENU] button while making settings, a
message asking you to confirm that you want to exit the setting
process appears. Note that if you choose "YES, " then press the
[ENTER] button, you are returned to the usual screen, and all
setting changes you've made up to that point will be discarded.
End
Modifying Recorded Phrases (Phrase Settings)

Repeat Play (Repeat, Repeat Interval)

This makes the settings for repeated playback of a phrase.
Repeat playback section is equivalent to the playback point
(described earlier).
Repeat:
This sets the number of times playback is repeated.
(For example, when the number of repetitions is set
to five times, the phrase is played back a total of six
times.) When the number of repetitions is set to ON,
playback repeats endlessly.
Interval:
This sets the playback interval as a time value.
Repeat Interval
Phrase1
Procedure for making repeat play settings
1.
Use the [SELECT] dial to choose the phrase whose setting
you want to change.
2.
Press the [MENU] button.
The MENU indicator lights up.
3.
Use the [SELECT] dial to choose "1.4 Repeat Play," then
press the dial.
You can reselect a phrase whose setting you want to change by
pressing the [BACK] (USER) button. The entry position (highlighted)
moves to the phrase selection, so turn the [SELECT] dial to reselect
card and the phrase number, then press the dial.
4.
Turn the [SELECT] dial to choose Repeat (OFF/ON/1 to 99),
then press the dial.
Turn the [SELECT] dial to set the Repeat Interval (from 00 m 00 s to
59 m 59 s), then press the dial.
* The number of the repeat interval can be valid only when repeat
"ON" or "1–99" is selected.
5.
When the prompt appears on the screen, press the
[ENTER] button to enable the settings.
To quit without making the settings, use the [SELECT] dial to
choose "NO, " then press the [ENTER] button.
Once the settings have been successfully modified, you're returned
to the setting item selection screen.
6.
Press the [MENU] button.
This ends the setting process and returns you to the usual screen.
* While making the settings, you can go back to the previous
entry location (highlighted) by pressing the [BACK] (USER)
button.
* If you press the [MENU] button while making settings, a
message asking you to confirm that you want to exit the setting
process appears. Note that if you choose "YES, " then press the
[ENTER] button, you are returned to the usual screen, and all
setting changes you've made up to that point will be discarded.
Phrase1
5