Ar-3000Sd Settings; Selecting The Direct Playback Method (Normal/First-In/Last-In/Sequence) - Roland AR-3000SD Reference Manual

Controlling the AR-3000SD from an External Device (Control Input Terminals)
Last-in playback
The control signal that is input later is given precedence in
playback.
During phrase playback, when a different START signal is newly
input, playback of the current phrase is stopped, and playback of
the specified phrase begins.
Port No.1
Port No.2
AUDIO OUTPUT
Playback is repeated while the control signal is continuously input.
Port No.1
AUDIO OUTPUT
Sequence playback
When a new control signal is input during phrase playback, the new
phrase is then stored (queued).
When playback of the current phrase is finished, the subsequently
specified phrase is played back.
A maximum of 100 phrases can be stored (queued).
Port No.1
Port No.2
AUDIO OUTPUT
Even when control signals are input continuously, playback is
conducted one time only and then ends.
Port No.1
AUDIO OUTPUT

AR-3000SD Settings

NOTE
If a card in AR-2000 format is inserted in either slot (or both),
the AR-3000SD can be used only for playback, and it is not
possible to record phrases or make any settings. Also, if you
insert a card in AR-2000 format into either slot (or both) while
making settings, the operation will halt with an error message.
Thereafter, the operation cannot be resumed until all cards are
removed.
Selecting the Control Input Mode
Select "DIRECT PLAY" from the control input modes (DIRECT PLAY/
PROGRAM PLAY/BINARY PLAY/BINARY REC).
* You cannot achieve control input playback merely by
connecting a device to the port. Be sure to set the control input
mode to match the method used for connecting to the ports.
Procedure for setting the control input mode
1.
Press the [MENU] button.
The MENU indicator lights up.
26
A0001 A0002
A0001 Interrupted
A0001 A0001 A0001
A0001 A0002
Disabled
A0001
2.
Use the [SELECT] dial to choose "5.1 Ctrl Input Mode," then
press the dial.
3.
Turn the [SELECT] dial to choose "DIRECT PLAY," then press
the dial.
4.
When the prompt appears on the screen, press the
[ENTER] button to enable the settings.
To quit without making the settings, use the [SELECT] dial to
choose "NO, " then press the [ENTER] button.
Once the settings have been made successfully, you're returned to
the setting item selection screen.
5.
Press the [MENU] button.
This ends the setting process and returns you to the usual screen.
* If you press the [MENU] button while making settings, a
message asking you to confirm that you want to exit the setting
process appears. Note that if you choose "YES, " then press the
[ENTER] button, you are returned to the usual screen, and all
setting changes you've made up to that point will be discarded.
Selecting the Direct Playback Method
(NORMAL/FIRST-IN/LAST-IN/SEQUENCE)
Select the Direct Playback Method (NORMAL/FIRST-IN/LAST-IN/
SEQUENCE) to be used.
& "Operational Specifications for Direct Playback" (p. 25)
Procedure for setting the direct playback method
1.
Press the [MENU] button.
The MENU indicator lights up.
2.
Use the [SELECT] dial to choose "5.2 Direct Play," then
press the dial.
3.
Turn the [SELECT] dial to choose the Direct Playback
system (NORMAL, FIRST-IN, LAST-IN, or SEQUENCE), then
press the dial.
5 If making the settings in "Assigning Phrases to the Ports" (p. 27),
proceed to Step 4 in the procedure for assigning the phrases.
5 To quit making settings, press the [ENTER] button.
4.
When the prompt appears on the screen, press the
[ENTER] button to enable the settings.
To quit without making the settings, use the [SELECT] dial to
choose "NO, " then press the [ENTER] button.
Once the settings have been made successfully, you're returned to
the setting item selection screen.
5.
Press the [MENU] button.
This ends the setting process and returns you to the usual screen.