GE F60 UR Series Instruction Manual page 218

5.4 FLEXLOGIC™
Table 5–7: F60 FLEXLOGIC™ OPERANDS (Sheet 7 of 8)
OPERAND TYPE OPERAND SYNTAX
INPUTS/OUTPUTS: Cont Ip 1
Contact inputs Cont Ip 2
Cont Ip 1
Cont Ip 2
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
current
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
voltage
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
INPUTS/OUTPUTS DIRECT INPUT 1 On
Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual inputs
Virt Ip 64
5
INPUTS/OUTPUTS: Virt Op 1
Virtual outputs
Virt Op 96
LED INDICATORS: LED IN SERVICE
Fixed front panel LED TROUBLE
LEDs LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
LED INDICATORS: LED TEST IN PROGRESS
LED test
LED INDICATORS: LED USER 1
User-programmable
LED USER 2 to 48
LEDs
REMOTE DEVICES REMOTE DEVICE 1 On
REMOTE DEVICE 16 On
REMOTE DEVICE 1 Off
REMOTE DEVICE 16 Off
RESETTING RESET OP
RESET OP (COMMS)
RESET OP (OPERAND)
RESET OP (PUSHBUTTON)
5-92
OPERAND DESCRIPTION
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
IOff (will not appear unless ordered)
IOff (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on.
Asserted when the front panel TROUBLE LED is on.
Asserted when the front panel TEST MODE LED is on.
Asserted when the front panel TRIP LED is on.
Asserted when the front panel ALARM LED is on.
Asserted when the front panel PICKUP LED is on.
Asserted when the front panel VOLTAGE LED is on.
Asserted when the front panel CURRENT LED is on.
Asserted when the front panel FREQUENCY LED is on.
Asserted when the front panel OTHER LED is on.
Asserted when the front panel PHASE A LED is on.
Asserted when the front panel PHASE B LED is on.
Asserted when the front panel PHASE C LED is on.
Asserted when the front panel NEUTRAL/GROUND LED is on.
An LED test has been initiated and has not finished.
Asserted when user-programmable LED 1 is on.
The operand above is available for user-programmable LEDs 2 through 48.
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Reset command is operated (set by all three operands below).
Communications source of the reset command.
Operand (assigned in the
of the reset command.
Reset key (pushbutton) source of the reset command.
F60 Feeder Protection System
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
INPUTS/OUTPUTS
5 SETTINGS
menu) source
RESETTING
GE Multilin