Table of Contents
Advertisement
V V
V V
V V
V V
C C
C C
C C
C C
R R
R R
R R
R R
M M
M M
M M
M M
o o
o o
o o
o o
d d
d d
d d
d d
e e
e e
e e
e e
Audio Dubbing
You can add music or narration to the recorded
Cassette.
OIf the tape recorded in the [16bit] Mode is dubbed
with the Audio Dubbing function, the original sound
is erased. (If you wish to preserve the original
sound, use the [12bit] Mode when recording.)
OAudio Dubbing cannot be performed on a recording
done in LP Mode. (-18-)
1
Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP]
>> [AV JACK] >> [IN/OUT].
W.B/SHUTTER/IRIS
VOL/JOG
MENU
2
Continuing the aforesaid setup, select [A.DUB
INPUT] >> [MIC] or [AV IN].
OSet to [AV IN] when external device is used, and
to [MIC] when an external or built-in microphone
is used.
3
Switch the Camera Recorder over to the Still
Playback Mode where you want to add new
sound.
4
Press the [A.DUB] Button
Controller.
MULTI/
P-IN-P
REC
C
/REW
PLAY
STILL ADV PAUSE STILL ADV
INDEX
STOP
5
To start Audio Dubbing, press the [;] Button
on the Remote Controller.
To Cancel Audio Dubbing
Press the [;] Button
on the Remote Controller.
The Camera Recorder is in the Still Playback Mode
again.
To dub audio while listening to a pre-recorded
sound
When pausing the audio dubbing, [12bit AUDIO] on
the [PLAYBACK FUNCTIONS] Sub-Menu is
automatically set to [ST2] and you can check the pre-
recorded sound. When a microphone is used for audio
dubbing, use headphones to listen to the pre-recorded
sound while dubbing the audio. (When using
headphones, set [AV JACK] on the [AV IN/OUT
SETUP] Sub-Menu to [OUT].) When the line input is
used, you can dub audio while listening to a pre-
recorded sound from the speaker.
38
on the Remote
A.DUB
B
FF/
INDEX
To Play Back the Sound Recorded by 12bit Audio
Dubbing
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS]
>> [12bit AUDIO] >> [ST2] or [MIX].
ST1: It plays back only the original sound.
ST2: It plays back only the sound added by Audio
Dubbing.
MIX: It plays back both the original sound and the
sound added by Audio Dubbing simultaneously.
OFor other notes concerning this item, see -45-.
$ To Adjust the Audio Level
You can adjust the Audio Level for Audio Dubbing.
1
Set [VCR FUNCTIONS] >> [RECORDING SETUP]
>> [AUDIO LEVEL] >> [YES].
W.B/SHUTTER/IRIS
VOL/JOG
MENU
OThe [AUDIO LEVEL SETUP] Menu appears.
2
Press the [PUSH] Dial
(AGC, NO-AGC)].
OThe Audio Level Meter appears.
A U D I O L E V E L S E T U P
M O D E
A U T O
( A G C ) ( N O – A G C )
( d B ) – 3 0
G A I N | | | | | | | | | | | – – –
P U S H M E N U T O R E T U R N
3
Turn the [PUSH] Dial
the bars of the [GAIN] Indication.
W.B/SHUTTER/IRIS
VOL/JOG
OFor details, refer to the [MIC LEVEL ADJ.] on the
[RECORDING SETUP] Sub-Menu of the [CAMERA
FUNCTIONS] Main-Menu (-31-).
to select the [MNL
M N L
M N L Ł
0
+ 6 Ł
to increase or decrease
Hide quick links:
Advertisement
Table of Contents
