Lista De Repuestos - Husky HDS126 Operating Instructions And Parts Manual

Manual de Instrucciones & Lista de Repuestos
Para Ordenar Repuestos o Asistencia Técnica, Sírvase Llamer al
Distribuidor Más Cercano a Su Domicilio
Sírvase darnos la siguiente información:
- Número del modelo
- Número de Serie o código con fecha (de haberlo)
- Descripción y número del repuesto según la lista de repuestos
20
16
5
4
3
2
1
21

Lista de Repuestos

No. de
Ref. Descripción
1 Boquilla de la pistola
2A Boquilla de cerámica
2B Boquilla de carburo
3 Sello
4 Boquilla
5 Tornillo de fijación
6 Anillo en O
7 Propulsor de aire
8 Cuerpo de la pistola
9 Resorte de la válvula
10 Anillo en O
11 Tapón de la válvula
12 Válvula (parte interna)
13 Gatillo
14 Pasador del gatillo
15 Llave Allen (3 mm - 1/8 in.)
16 Anillo en O
17 Sello de la válvula
18 Sello interno
19 Anillo en O
20 Tubo recolector
21 Manguera de material
■
Juego de repuestos para reparar el gatillo & válvula
(●) Ordene el Modelo MP3109 para el juego de boquilla de cerámica y propulsor de aire
(▲) Ordene el Modelo MP3110 para el juego de boquilla de carburo y propulsor de aire
❋ Artículo estándar de ferretería
Puede escribirnos a:
Attn: Parts Department
100 Production Drive
Harrison, OH 45030 U.S.A.
8
6
7
6,4mm (1/4 in. NPT) (H)
14
18
9
13
10
11
19
17
15
12
No.
AT210100AV
●
▲
● ▲
AT210400AV
---
● ▲
● ▲
---
■
■
■
■
■
■
❋
● ▲
■
■
■
SV900900AV
SV901000AJ
SV212000AV
20 Sp
Suggested Uses
Type of
Abrasive
(Sieve/Size)
Sand
(30-50)
Glass beads
Sand (40)
Ground walnut
shells
Sand (50-100)
Glass beads,
ground walnut
shells
Sand
(20-40)
Sand (20-40)
Aluminum
oxide
Sand
(20-40)
Ground pecan
or walnut
shells and corn
cob meal
Ctd.
Sand (20-50)
Aluminum
1
oxide (50-80)
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
Distance
Application from psi Suggestions
Work
Etching and 1 - 4 in. 40 - 90 Move gun back and forth over the template in a
drilling holes in
brushing manner. Blast at a 90° angle. For fine polishing,
glass
use glass beads for the abrasive. For drilling holes, use 30
sieve sand.
Antiquing or 2 - 6 in. 40 - 90 Use brushing strokes and watch the abrasion rate
weathering wood carefully. Soft wood will wear faster than hardwood.
Smaller grit sizes gives smoother finish. Start with low
pressure and gradually build up pressure. Blast at a 45°
angle.
Wood sanding
1 - 6 in. 40 - 70 Use brushing strokes and watch the abrasion rate
and refinishing
carefully. Use walnut shells for coarse finishing and glass
furniture
beads or fine sand for fine finishing. Blast at a 45° angle.
Cleaning 1 - 4 in. 50 - 125 Be sure to mask any glass or painted surface that could
barbeque grills be accidentally damaged. Blast at a 80 - 90° angle.
and iron pots
Cleaning
1 - 4 in. 40 - 80 Use larger grit sand on a hidden area. If the base
automotive parts
material is being damaged, use a smaller grit. Blast at a
80 - 90° angle.
Cleaning and 1 - 4 in. 50 - 125 Use a heavy grit sand with a sweeping overlapping
stripping masonry stroke. Blast at a 80 - 90° angle.
Cleaning or 1 - 6 in. 40 - 125 Use brushing strokes and watch the abrasion rate
preparing for
carefully. Soft wood will wear faster than hard wood.
paint
Smaller grit sizes five a smoother finish. Start with low
pressure and gradually build up pressure. Blast at a
45 - 60° angle.
Cleaning or 1 - 3 in. 50 - 125 Remove flaking paint first with wire brush, then
stripping outdoor sandblast with a heavy grit abrasive. Multiple layer of
equipment old paint should be scraped first. Prime immediately
following sandblasting to prevent corrosion. Blast at a
45 - 60° angle.
5
Model HDS126