Operation - Toolson PRO-ST 65 Original Operating Instructions

groove (c) of the blade holder (14) as far as
the stop.
•
Tighten the screw (a/b) with the supplied
Allen key.
•
The teeth on the saw blade must be pointing
in the direction of cutting. Check that the saw
blade is positioned in the guide groove (c) of
the blade holder (14) and the roller.
•
Check that the saw blade (12) is securely
mounted in the blade holder.
•
Follow the instructions above in reverse order
to remove the saw blade.
5.3 Installing the parallel stop (Figure 3/
Item 11)
•
The parallel stop (11) enables you to saw
parallel cuts.
•
Undo the two locking screws (13) on the so-
leplate (7).
•
Now slide the parallel stop (11) into the
guides on the soleplate (7). You can fit the
parallel stop (11) on either the left or right of
the equipment.
•
The guide strip must always face downwards.
Set the required distance using the measu-
rement scale on the parallel stop (11) and
tighten the locking screws (13) again.
5.4 Setting the soleplate for miter cuts
(Figs. 4-5)
•
Use the Allen key (4) to loosen the screws for
the soleplate (16) on the bottom of the adjus-
table soleplate (7) (Figure 4).
•
Pull the soleplate (7) slightly forward. The so-
leplate can now be swiveled a maximum 45°
to the left and right.
•
If the soleplate (7) is pushed back to the
rear again, it will only function in the locking
positions at 0°, 15°, 30° and 45°, which are
marked on the graduated scale for the sole-
plate (9) (Figure 5). Move the soleplate into
the required position and refasten the screw
securing the soleplate (16).
•
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate
(7) forwards, set the desired angle and refas-
ten the screw securing the soleplate (16).
5.5 Adapter for dust extraction system
(Figure 6)
The jigsaw is equipped with an adapter for the
vacuum cleaner connection. Place the adaptor
onto the jigsaw and secure by turning it. Any va-
cuum cleaner can be connected to the extractor
adaptor. Check that the connections are air-tight.
Anl_PRO_ST_65_SPK7.indb 17 Anl_PRO_ST_65_SPK7.indb 17
GB
Dust created when working may be dangerous.
Be sure to observe the safety instructions.

6. Operation

6.1 ON/OFF switch (Fig. 7/Item 3)
To switch on:
Press the ON/OFF switch
To switch off :
Release the ON/OFF switch
6.2 Locking button (Fig. 7/Item 2)
You can lock the ON/OFF switch (3) using the lo-
cking button (2) when the equipment is in operati-
on. To switch off the equipment briefl y hold down
the ON/OFF switch (3).
6.3 Electric speed selector (Fig. 8/Item 1)
You can pre-select the required speed with the
speed selector. Turn the speed selector in PLUS
director to increase the speed and turn the speed
selector in MINUS direction to reduce the speed.
The suitable stroke speed is dependent on the
relevant material and working conditions.
General rules for cutting speeds for metal cutting
work must be complied with here as well.
You can generally use a higher speed with fi ne
saw blades whilst coarser saw blades require
lower speeds.
Position 1-2 = low stroke speed (for steel)
Position 3-4 = medium stroke speed (for steel,
soft metal, plastic)
Position 5-6 = high stroke speed (for softwood,
hardwood, soft metal, plastic)
6.4 Setting the pendulum action (Fig. 9/
Item 8)
•
The strength of the pendulum action of the
saw blade (12) can be adjusted using the se-
lector switch for pendulum action (8).
•
You can adjust the cutting speed, the cutting
performance and the finish to the workpiece
you wish to saw.
Set the selector switch for pendulum action (8) to
one of the following positions:
- 17 -
18.05.15 10:49 18.05.15 10:49