Fiat 500 X 2016 Owner's Manual

page of 608

/ 608
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

FIAT 500X

2 0 1 6

O W N E R ' S M A N U A L

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the 500 X 2016 and is the answer not in the manual?

Questions and answers

Summary of Contents for Fiat 500 X 2016

Page 1 FIAT 500X 2 0 1 6 O W N E R ’ S M A N U A L...
Page 2 This manual illustrates and describes the operation of VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 CUSTOMER ASSISTANCE .
Page 5: Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE MODIFICATIONS/ALTERATIONS ..7 HOW TO USE THIS MANUAL ....4 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION • The range of additional services available to FCA US INTRODUCTION LLC customers Congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- NOTE: After reviewing the owner information, it tive styling, and high quality - all essentials that are should be stored in the vehicle for convenient referenc- traditional to our vehicles.
Page 7 INTRODUCTION 5 The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
Page 8 6 INTRODUCTION...
Page 9: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS ROLLOVER WARNING This Owner’s Manual contains WARNINGS against Utility vehicles have a significantly higher rollover rate operating procedures that could result in a collision, than other types of vehicles. This vehicle has a higher bodily injury and/or death. It also contains CAUTIONS ground clearance and a higher center of gravity than against procedures that could result in damage to your many passenger vehicles.
Page 10 8 INTRODUCTION two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. Rollover Warning Label Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury.
Page 11: Table Of Contents
REPORTING SAFETY DEFECTS ... . .15 ▫ FIAT Customer Center ....12 ▫ In The 50 United States And Washington, D.C.
Page 12 10 CUSTOMER ASSISTANCE ▫ Traction Grades......17 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....17 ▫...
Page 13: Suggestions For Obtaining Service For Your Vehicle
CUSTOMER ASSISTANCE 11 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 14: Fiat Customer Center
1-888-242-6342 solved with this process. • If for some reason you are still not satisfied, talk to the FIAT Canada Customer Center general manager or owner of the authorized dealer. P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1-800- They want to know if you need assistance.
Page 15: Puerto Rico And U.s. Virgin Islands
CUSTOMER ASSISTANCE 13 Puerto Rico And U.S. Virgin Islands Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered Customer Service Chrysler International Services LLC by Bell Canada. For TTY teletypewriter users, dial 711 P.O.
Page 16: Warranty Information
14 CUSTOMER ASSISTANCE The manufacturer will not stand behind any service WARNING! contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the Engine exhaust (internal combustion engines only), manufacturer’s service contract. If you purchased a ser- some of its constituents, and certain vehicle compo- vice contract that is not a manufacturer’s service contract, nents contain, or emit, chemicals known to the State...
Page 17: Reporting Safety Defects
CUSTOMER ASSISTANCE 15 REPORTING SAFETY DEFECTS You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In The 50 United States And Washington, D.C. In Canada If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should If you believe that your vehicle has a safety defect, you immediately inform the National Highway Traffic Safety should contact the Customer Service Department imme-...
Page 18: Customer Assistance
16 CUSTOMER ASSISTANCE NOTE: A street address is required when ordering problems the first time, using step-by-step troubleshoot- manuals (no P.O. Boxes). ing and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment. Service Manuals Owner’s Manuals These comprehensive Service Manuals provide the infor- mation that students and professional technicians need in...
Page 19: Department Of Transportation Uniform Tire Quality Grades
CUSTOMER ASSISTANCE 17 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- teristics and climate. The following tire grading categories were established by the National Highway Traffic Safety Administration. The Traction Grades specific grade rating assigned by the tire’s manufacturer The Traction grades, from highest to lowest, are AA, A, B,...
Page 20: Temperature Grades
18 CUSTOMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, The temperature grade for this tire is established for representing the tire’s resistance to the generation of heat a tire that is properly inflated and not overloaded. and its ability to dissipate heat, when tested under Excessive speed, under-inflation, or excessive load- controlled conditions on a specified indoor laboratory...
Page 21 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......20 INTERIOR......23 REAR VIEW .
Page 22: Front View
20 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Engine Compartment 4 — Outside Mirrors 2 — Headlights 5 — Doors 3 — Windshield 6 — Wheels...
Page 23: Rear View
GRAPHICAL TABLE OF CONTENTS 21 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 24: Instrument Panel
22 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 7 — Upper Switch Bank 13 — Lower Switch Bank 2 — Multifunction Lever 8 — Upper Storage Compartment 14 — Driver Side Knee Air Bag 3 — Instrument Cluster 9 —...
Page 25: Interior
GRAPHICAL TABLE OF CONTENTS 23 INTERIOR Interior Features 1 — Power Window Switches 6 — Seats 2 — Headlight Switch 7 — Switch Panel 3 — Instrument Cluster 8 — Transmission Gear Selector (Automatic/Manual Options) 4 — Audio System 9 — Electronic Speed Controls 5 —...
Page 27 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... .30 REMOTE STARTING SYSTEM — IF EQUIPPED .
Page 28 26 GETTING TO KNOW YOUR VEHICLE ▫ Remote Start Windshield Wiper De–Icer ▫ Child Locks ......61 Activation —...
Page 29 GETTING TO KNOW YOUR VEHICLE 27 ▫ Automatic Lighting — If Equipped ..91 MIRRORS ......77 ▫...
Page 30 28 GETTING TO KNOW YOUR VEHICLE ▫ Opening The Sunroof....131 WIPERS AND WASHERS ....100 ▫...
Page 31 GETTING TO KNOW YOUR VEHICLE 29 ▫ Cargo Area Features ....139 ▫ Ashtray — If Equipped ....148 ▫...
Page 32: Keys
30 GETTING TO KNOW YOUR VEHICLE KEYS Mechanical Key Fob The metal insert of the Key Fob operates: • The Ignition System • Driver’s Door Lock Mechanical Key Fob 1 — Mechanical Key 2 — Door Lock Button 3 — Door Unlock Button 4 —...
Page 33: Electronic Key Fob
GETTING TO KNOW YOUR VEHICLE 31 Electronic Key Fob On versions equipped with Keyless Enter-N-Go, the car is equipped with an Electronic Key Fob. The Key Fob with Remote Control contains a Remote Keyless Entry (RKE) transmitter. The RKE system allows you to lock or unlock the doors and liftgate or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a handheld Key Fob with a RKE transmitter.
Page 34: Key Fob Operation
32 GETTING TO KNOW YOUR VEHICLE Key Fob Operation Unlocking Doors And Liftgate The driver’s door may be unlocked by inserting the vehicle key into the exterior driver’s door lock cylinder. To unlock all the doors, push the interior power door UNLOCK button on the door panel.
Page 35 GETTING TO KNOW YOUR VEHICLE 33 UNLOCK button on the RKE transmitter. To change the Key Fob With Remote Control And Integrated Vehicle current setting, refer to “Uconnect Settings” in “Multime- dia” for further information. If one or more doors are open, or the liftgate is open, the NOTE: If the vehicle is equipped with Passive Entry, doors will lock.
Page 36: Replacing The Battery In The Key Fob With Remote Control
34 GETTING TO KNOW YOUR VEHICLE • Refer to “Electronic Vehicle Information Center RKE transmitter apart using a screwdriver or similar (EVIC)” in “Getting To Know Your Instrument Panel” tool. Make sure not to damage the seal during re- or “Uconnect Settings” in “Multimedia” for further moval.
Page 37 GETTING TO KNOW YOUR VEHICLE 35 2. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover.
Page 38 36 GETTING TO KNOW YOUR VEHICLE Separating Keyless Enter-N-Go Transmitter Case 1. Remove the emergency key by sliding the mechanical latch on the back of the RKE transmitter sideways with your thumb. Then, pull the key out with your other hand. 2.
Page 39: Request For Additional Keys
GETTING TO KNOW YOUR VEHICLE 37 located on the back cover. Avoid touching the new Request For Additional Keys battery with your fingers. Skin oils may cause battery NOTE: Only Key Fobs that are programmed to the deterioration. If you touch a battery, clean it with rubbing vehicle electronics can be used to start and operate the alcohol.
Page 40: General Information
38 GETTING TO KNOW YOUR VEHICLE NOTE: When having the Sentry Key Immobilizer System IGNITION SWITCH serviced, bring all vehicle keys with you to an authorized Operation dealer. Your vehicle uses either a key start ignition system or General Information keyless ignition system.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 • Some electrical devices (e.g. power locks, alarm, etc.) are still available. 2 — MAR/RUN • Driving position. • Electrical devices are available. 3 — AVV/START • Start the engine. The ignition switch is provided with a safety mechanism. If the engine fails to start, the ignition will return to the Integrated Mechanical Key Ignition STOP/OFF position prior to repeating the starting pro-...
Page 42 40 GETTING TO KNOW YOUR VEHICLE Electronic Key This Keyless Enter-N-Go system feature allows the driver to operate the ignition switch with the push of a button as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Push Button Ignition has three operating positions.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 • Some electrical devices (e.g. Central locking, alarm, WARNING! (Continued) etc.) are still available. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is •...
Page 44: Remote Starting System - If Equipped
42 GETTING TO KNOW YOUR VEHICLE 2. This device must accept any interference received, CAUTION! including interference that may cause undesired op- eration. An unlocked car is an invitation. Always remove key from the ignition and lock all doors when leaving the NOTE: Changes or modifications not expressly approved vehicle unattended.
Page 45: Remote Start Cancel Message - If Equipped
GETTING TO KNOW YOUR VEHICLE 43 • Remote Start Cancelled — Too Cold NOTE: • The vehicle must be equipped with an automatic • Remote Start Cancelled — Time Expired transmission to be equipped with Remote Start. The message will stay active until the ignition is placed in •...
Page 46: To Enter Remote Start Mode
44 GETTING TO KNOW YOUR VEHICLE • RKE PANIC button not pushed To Enter Remote Start Mode • System not disabled from previous remote start event Push and release the REMOTE START button • Vehicle alarm system indicator flashing on the RKE transmitter twice within five sec- •...
Page 47: To Exit Remote Start Mode Without Driving The Vehicle
GETTING TO KNOW YOUR VEHICLE 45 To Exit Remote Start Mode Without Driving The NOTE: For vehicles equipped with the Keyless Enter- Vehicle N-Go feature, the message “Remote Start Active — Push Start Button” will display in the Electronic Vehicle Infor- Push and release the REMOTE START button one time or mation Center (EVIC) or the Driver Information Dispay allow the engine to run for the entire 15-minute cycle.
Page 48: Remote Start Windshield Wiper De-Icer Activation - If Equipped
46 GETTING TO KNOW YOUR VEHICLE NOTE: The Remote Start Comfort System can be acti- This device complies with Part 15 of the FCC Rules and vated and deactivated through the Uconnect Settings. For with Industry Canada license-exempt RSS standard(s). more information on Remote Start Comfort System op- Operation is subject to the following two conditions: eration, refer to “Uconnect Settings”...
Page 49: General Information
GETTING TO KNOW YOUR VEHICLE 47 The system uses a Key Fob with a factory-mated Remote CAUTION! Keyless Entry (RKE) transmitter, a Keyless Push Button • Do not make modifications or alterations to the Ignition, and a RF receiver to prevent unauthorized vehicle operation.
Page 50: Vehicle Security Alarm
48 GETTING TO KNOW YOUR VEHICLE • Park lamps and/or turn signals will flash. 2. This device must accept any interference received, including interference that may cause undesired op- • Vehicle Security Light in the instrument cluster will eration. flash. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 51: To Arm The System
GETTING TO KNOW YOUR VEHICLE 49 To Arm The System same exterior zone (for further information, refer to Keyless Enter-N-Go in Getting To Know Your Follow these steps to arm the Vehicle Security Alarm: Vehicle”). 1. Make sure the vehicles ignition is cycled to the STOP/ •...
Page 52: To Disarm The System
50 GETTING TO KNOW YOUR VEHICLE To Disarm The System NOTE: • The driver’s door key cylinder cannot arm or disarm The Vehicle Security Alarm can be disarmed using any of the following methods: the Vehicle Security Alarm. • Push the UNLOCK button on the Remote Keyless •...
Page 53: Disabling
GETTING TO KNOW YOUR VEHICLE 51 Disabling If the lock symbol is visible when the door is shut, the door will lock. Therefore, make sure the Key Fob is not To completely disable the alarm (e.g. in the case of long inside the vehicle before closing the door.
Page 54: Central Lock/Unlock
52 GETTING TO KNOW YOUR VEHICLE NOTE: The manual lock knob unlocks each individual WARNING! (Continued) door separately as well as the liftgate. child could operate power windows, other controls, or move the vehicle. WARNING! • Do not leave children or animals inside parked •...
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Locking/Unlocking From The Inside The doors can also be locked and unlocked with the Keyless Enter-N-Go (Passive Entry) system if equipped. Push the LOCK button on the driver or passenger door For further information, refer to “Keyless Enter-N-Go” in trim panel to lock the doors.
Page 56: Keyless Enter-N-Go
54 GETTING TO KNOW YOUR VEHICLE Keyless Enter-N-Go To Unlock From The Driver’s Side The Passive Entry system is an enhancement to the With a valid Passive Entry RKE transmitter within 5 ft vehicle’s Remote Keyless Entry (RKE) system and a (1.5 m) of the driver’s door handle, grab the front driver feature of Keyless Enter-N-Go.
Page 57 GETTING TO KNOW YOUR VEHICLE 55 NOTE: If “Unlock All Doors 1st Press” is programmed, To Lock The Vehicle’s Doors And Liftgate all doors will unlock when you grab hold of the front With one of the vehicle’s Passive Entry RKE transmitters driver’s door handle.
Page 58 56 GETTING TO KNOW YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry RKE Transmitter In Vehicle (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry RKE transmitter inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function if the ignition switch is in the OFF position.
Page 59 GETTING TO KNOW YOUR VEHICLE 57 When any of these situations occur, after all ajar doors are Emergency Unlocking Driver Door shut, the FOBIK-Safe search will be executed. If it finds a If the Remote Keyless Entry (RKE) transmitter battery is Passive Entry RKE transmitter inside the car, and it does low or dead, the emergency key can be used to unlock the not find any Passive Entry RKE transmitters outside the...
Page 60 58 GETTING TO KNOW YOUR VEHICLE WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed.
Page 61 GETTING TO KNOW YOUR VEHICLE 59 To Unlock/Enter The Liftgate NOTE: If “Unlock All Doors 1st Press” is programmed in EVIC/DID, if equipped, all doors will unlock when you The liftgate Passive Entry unlock feature is built into the push the Electronic Release. If Unlock Driver Door 1st electronic liftgate release.
Page 62 60 GETTING TO KNOW YOUR VEHICLE General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 63: Child Locks
GETTING TO KNOW YOUR VEHICLE 61 Child Locks To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system. To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial to the LOCK or UNLOCK position.
Page 64: Seats
62 GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! • When the child lock system is engaged, the door can Avoid trapping anyone in a vehicle in a collision. only be opened by using the outside door handle even Remember that the rear doors can only be opened though the inside door lock is in the unlocked position.
Page 65: Manual Front Seats
GETTING TO KNOW YOUR VEHICLE 63 Manual Front Seats WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 66 64 GETTING TO KNOW YOUR VEHICLE Manual Front Seat Forward/Rearward Adjustment WARNING! (Continued) On models equipped with manual seats, the forward/ • Do not ride with the seatback reclined so that the rearward adjusting bar is located at the front of the seats, shoulder belt is no longer resting against your near the floor.
Page 67: Power Adjustment (Front) - If Equipped
GETTING TO KNOW YOUR VEHICLE 65 Power Adjustment (Front) — If Equipped The power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/ rearward, tilt if equipped and to set the angle of the seatback.
Page 68: Heated Seats - If Equipped
66 GETTING TO KNOW YOUR VEHICLE Forward Or Rearward Adjustment Tilt Adjustment The seat can be adjusted both forward and rearward. The angle of the seat cushion can be adjusted up or Push the seat switch forward or rearward, the seat will down.
Page 69 GETTING TO KNOW YOUR VEHICLE 67 • Push the heated seat button a second time to turn Auto On Comfort — If Equipped the LO setting ON. If the external temperature is below 41 °F (5 °C) at each start-up of the vehicle the heated seat functionality of the •...
Page 70: Rear Seats
68 GETTING TO KNOW YOUR VEHICLE Rear Seats WARNING! The split rear seat increases the storage of the rear cargo • It is extremely dangerous to ride in a cargo area, area. inside or outside of a vehicle. In a collision, people NOTE: riding in these areas are more likely to be seriously injured or killed.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 4. The rear shelf can be stored in the cargo area, or behind the front seatbacks. Partial Enlargement Of Cargo Area Enlargement of the left side of the cargo area allows you to carry a single passenger on the right side of the rear seat, while the enlargement of the right side allows you to carry two passengers.
Page 72 70 GETTING TO KNOW YOUR VEHICLE 2. Fully lower the rear seat head restraints. 3. Move the safety belts to the outboard side of the seat. 4. Pull the seatback release lever to fold both sides of the rear seatbacks completely forward. Seatback Repositioning NOTE: If interference from the cargo area prevents the seatback from fully locking, you will have difficulty...
Page 73: Head Restraints
GETTING TO KNOW YOUR VEHICLE 71 WARNING! (Continued) for child seats and/or passengers. An improperly latched seat could cause serious injury. HEAD RESTRAINTS Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.
Page 74: Front Head Restraints
72 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) or removed could cause serious injury or death in the event of a collision. Front Head Restraints Your vehicle is equipped with driver and passenger head restraints. To raise the head restraint, pull upward on the head restraint.
Page 75: Rear Head Restraints
GETTING TO KNOW YOUR VEHICLE 73 NOTE: Do not reposition the head restraint 180 degrees Rear Head Restraints to the incorrect position in an attempt to gain additional Your vehicle is equipped with two outboard head re- clearance to the back of the head. straints and one center head restraint for its rear passen- gers.
Page 76 74 GETTING TO KNOW YOUR VEHICLE NOTE: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. WARNING! • A loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle.
Page 77: Steering Wheel
GETTING TO KNOW YOUR VEHICLE 75 STEERING WHEEL Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column.
Page 78: Heated Steering Wheel - If Equipped
76 GETTING TO KNOW YOUR VEHICLE To unlock the steering column, push the tilt/telescoping Heated Steering Wheel — If Equipped lever downward (toward the floor). To tilt the steering The steering wheel contains a heating element that helps column, move the steering wheel upward or downward warm your hands in cold weather.
Page 79: Mirrors
GETTING TO KNOW YOUR VEHICLE 77 the rear window. Headlight glare from vehicles behind WARNING! you can be reduced by moving the lever under the mirror • Persons who are unable to feel pain to the skin to the night position (toward the rear of the vehicle). The mirror should be adjusted while the lever under the because of advanced age, chronic illness, diabetes, mirror is set in the day position (toward the windshield).
Page 80: Auto Dimming Mirror - If Equipped
78 GETTING TO KNOW YOUR VEHICLE NOTE: The mirror will automatically release in the event of heavy contact with a passenger. Auto Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror.
Page 81: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE 79 Outside Mirrors Power Adjustment Mirrors The power mirror switch is located on the drivers door panel. To adjust the mirror, push the mirror adjustment switch in the four directions indicated by arrows. NOTE: • To adjust the power mirrors, the ignition must be in the MAR/RUN position.
Page 82: Heated Mirrors - If Equipped
80 GETTING TO KNOW YOUR VEHICLE Folding Mirror Heated Mirrors — If Equipped The exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The These mirrors are heated to melt frost or ice. This mirror has three detent positions: full forward, normal feature can be activated whenever you turn on the and full rearward.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 The BSM detection zone covers approximately one lane width on both sides of the vehicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approxi- mately 20 ft (6 m) beyond the rear bumper of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert...
Page 84 82 GETTING TO KNOW YOUR VEHICLE The area on the rear fascia where the radar sensors are The BSM system notifies the driver of objects in the located must remain free of snow, ice, and dirt/road detection zones by illuminating the BSM warning light contamination so that the BSM system can function located in the outside mirrors in addition to sounding an properly.
Page 85 GETTING TO KNOW YOUR VEHICLE 83 The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries. Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle.
Page 86 84 GETTING TO KNOW YOUR VEHICLE Entering From The Rear Overtaking Traffic If you pass another vehicle slowly with a relative speed Vehicles that come up from behind your vehicle on either less than 15 mph (25 km/h) and the vehicle remains in side and enter the rear detection zone with a relative the blind spot for approximately 1.5 seconds, the warning speed of less than 31 mph (50 km/h).
Page 87 GETTING TO KNOW YOUR VEHICLE 85 Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 88: Rear Cross Path (Rcp)
86 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 89 GETTING TO KNOW YOUR VEHICLE 87 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
Page 90: Mode Of Operation
88 GETTING TO KNOW YOUR VEHICLE Mode Of Operation alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and de- Three selectable modes of operation are available in the tected object are present on the same side at the same Uconnect System.
Page 91: Blind Spot Monitoring Fault Warnings
GETTING TO KNOW YOUR VEHICLE 89 NOTE: The BSM system will store the current operating System Not Available mode when the vehicle is shut off. Each time the vehicle In the case of the system being temporary unavailable: is started the previously stored mode will be recalled and •...
Page 92: General Information
90 GETTING TO KNOW YOUR VEHICLE General Information EXTERIOR LIGHTS This vehicle has systems that operate on radio frequency Headlights that comply with Part 15 of the Federal Communications The headlight switch is located on the left side of the Commission (FCC) rules and with Industry Canada instrument panel.
Page 93: Automatic Lighting - If Equipped
GETTING TO KNOW YOUR VEHICLE 91 Automatic Lighting — If Equipped Light Sensor The light sensor is equipped with an infrared LED, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the Menu on the display or on the Uconnect system.
Page 94: Daytime Running Lights (Drl) - If Equipped
92 GETTING TO KNOW YOUR VEHICLE The timing of the headlights is adjustable between 0, 30, Front Fog Lights — If Equipped 60 and 90 seconds. Refer to “Uconnect Settings” in The front fog light switch is built into the headlight “Multimedia”...
Page 95: Parking Lights
GETTING TO KNOW YOUR VEHICLE 93 Parking Lights Headlight Delay Disable Rotate the headlight switch to the first position to turn on The feature is disabled by turning on the headlights, the the parking lights. The parking light indicator in the parking lights or by placing the ignition in the MAR/ cluster will illuminate.
Page 96: Turn Signals
94 GETTING TO KNOW YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. When the Daytime Running Lights are on and a turn signal is activated, the Daytime Running Lamp will turn off on the side of the vehicle in which the turn signal is flashing.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 NOTE: • Before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • If a light is left on it will automatically be turned off after approximately 15 minutes after the ignition is in the STOP/OFF position.
Page 98 96 GETTING TO KNOW YOUR VEHICLE • When one of the doors is opened, the dome light will Timing Exiting The Vehicle illuminate for approximately three minutes. The dome light will illuminate under the following • When the doors are closed, the dome light will auto- conditions when the ignition is turned to the STOP/OFF matically shut off after approximately 27 seconds.
Page 99 GETTING TO KNOW YOUR VEHICLE 97 This light automatically turn ON/OFF when the glove compartment is opened and closed, regardless of the position of the ignition. Vanity Mirror Light Lower Glove Compartment Light An interior light is located is the lower glove compart- Lower Glove Compartment Light ment.
Page 100: Rear Dome Light - If Equipped
98 GETTING TO KNOW YOUR VEHICLE Rear Dome Light — If Equipped Vehicles With Retractable Roof Push the button on the rear dome light once to turn the For vehicles equipped with a retractable roof, there are light ON, the light will remain ON at all times. Push the two interior lights located below the grab handles of the button a second time to turn the light OFF, the lights will rear doors.
Page 101: Cargo Area Lights
GETTING TO KNOW YOUR VEHICLE 99 Cargo Area Lights NOTE: In order to preserve the life of the battery, the light will turn off after 15 minutes. An interior light is located on the left side panel in the cargo area. Instrument Panel Dimmer And Ambient Light Control This light automatically turn ON/OFF when the liftgate...
Page 102: Wipers And Washers
100 GETTING TO KNOW YOUR VEHICLE WIPERS AND WASHERS Front Wiper Operation The windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
Page 103 GETTING TO KNOW YOUR VEHICLE 101 for several wipe cycles after the lever is released, and CAUTION! then resume the intermittent interval previously selected. Always remove any buildup of snow that prevents If the lever is pulled while the wipers are in the off the windshield wiper blades from returning to the position, the wipers will operate for several wipe cycles, “park”...
Page 104: Rain Sensor - If Equipped
102 GETTING TO KNOW YOUR VEHICLE Mist Use this feature when weather conditions make occa- sional usage of the wipers necessary. Push the lever upward to the Mist position and release for a single wiping cycle. NOTE: The mist feature does not activate the washer pump;...
Page 105 GETTING TO KNOW YOUR VEHICLE 103 wiper sensitivity. Setting two can be used if the driver The Rain Sensing system has protection features for the desires more sensitivity. Place the wiper switch in the wiper blades and arms, and will not operate under the OFF position when not using the system.
Page 106: Rear Window Wiper/Washer
104 GETTING TO KNOW YOUR VEHICLE the ignition switch in the MAR/RUN position, rain If the lever is pushed while the wiper is in the off sensing wiper operation can resume, if it has been position, the wiper will operate for several wipe cycles, selected, and no other inhibit conditions (mentioned then turn off.
Page 107: Windshield Wiper De-Icer - If Equipped
GETTING TO KNOW YOUR VEHICLE 105 To manually shut the defroster off, push the button a Windshield Wiper De-Icer — If Equipped second time. Your vehicle may be equipped with a Windshield Wiper De-Icer feature that may be activated under the following CAUTION! conditions: Failure to follow these cautions can cause damage to...
Page 108: Climate Controls
106 GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS Air Outlet And Diffuser Locations — Passenger Compartment Left Side Air Outlets 1 — Fixed Air Outlet 2 — Adjustable Air Outlet 3 — Air Vane Adjustment 4 — Air Flow Outlet Adjustment...
Page 109 GETTING TO KNOW YOUR VEHICLE 107 Right Side Air Outlets Center Air Outlets 1 — Fixed Air Outlet 2 — Adjustable Air Outlet 1 — Air Flow Outlet Adjustment 3 — Air Vane Adjustment 2 — Adjustable Air Outlet 4 — Air Flow Outlet Adjustment 3 —...
Page 110: Manual Climate Controls - If Equipped
108 GETTING TO KNOW YOUR VEHICLE Manual Climate Controls — If Equipped 1. Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control clockwise from the “0”...
Page 111 GETTING TO KNOW YOUR VEHICLE 109 • Panel • Mix Air is directed through the outlets in the Air is directed through the floor, defrost, and instrument panel. These outlets can be ad- side window demister outlets. This setting justed to direct airflow. works best in cold or snowy conditions that require extra heat to the windshield.
Page 112 110 GETTING TO KNOW YOUR VEHICLE 4. Rear Defrost Button NOTE: • Continuous use of the Recirculation mode may make Push and release the Rear Defrost Control button to turn the inside air stuffy and window fogging may occur. ON the rear window defroster and the heated outside Extended use of this mode is not recommended.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 Rear Window Defrosting Air Recirculation Push and release the rear window defrost button to turn Push and release the Air Recirculation button so that the the function on/off. LED is on, to enter recirculation mode. It is recommended to turn the internal air recirculation on while standing in Activation of this function is indicated by the rear defrost traffic or in tunnels to prevent the introduction of pol-...
Page 114: Automatic Climate Controls - If Equipped
112 GETTING TO KNOW YOUR VEHICLE System Maintenance Automatic Climate Controls — If Equipped In winter, the Climate Control system must be turned on at least once a month for approximately 10 minutes. Have the system inspected at an authorized dealership before the summer.
Page 115 GETTING TO KNOW YOUR VEHICLE 113 2. A/C Button 4. Blower Control Indicator LEDs Push the A/C Control Button to change the current A total of eight LEDs illuminate to visually indicate setting. The indicator illuminates when the A/C is ON. blower speeds.
Page 116 114 GETTING TO KNOW YOUR VEHICLE 7. Passenger Temperature Control 9. SYNC Button Provides the passenger with independent temperature Push the Sync button to toggle the Sync feature ON/OFF. control. Rotate the adjustment knob to set desired tem- The Sync indicator will illuminate when this feature is perature shown in the Temperature Display.
Page 117 GETTING TO KNOW YOUR VEHICLE 115 11. Blower Control NOTE: • When in Max Defrost mode, the Recirculation button Blower control is used to regulate the amount of air will change the setting to normal Defrost mode. This forced through the climate system. Adjusting the blower indicates that you can not enter to this mode due to will cause the automatic mode to change to manual fogging risk.
Page 118 116 GETTING TO KNOW YOUR VEHICLE • Blower speed (continuous variation of the air flow). Description • Compressor engagement (for cooling/dehumidifying The Automatic Dual Zone Climate Control system regu- lates the air temperatures in the passenger compartment the air). in two zones: driver side and passenger side. •...
Page 119 GETTING TO KNOW YOUR VEHICLE 117 1The air temperature is always automatically controlled NOTE: The Climate Control system detects the passenger according to the temperature set on the display (except compartment temperature using a temperature sensor, for when the system is off or in certain conditions when located in the lower instrument panel between the center the compressor is not running).
Page 120 118 GETTING TO KNOW YOUR VEHICLE time by using the relevant buttons or knobs: the system Turn the Passenger Temperature Control knob to return will automatically change the settings to adjust to the to the separate management of air temperatures in the new requirements.
Page 121 GETTING TO KNOW YOUR VEHICLE 119 • Panel Mode – Air flow is distributed between the NOTE: Air always flows from the side instrument panel central and side instrument panel vents. diffusers: it is, however, possible to interrupt the air flow by operating the wheel located near the corresponding •...
Page 122 120 GETTING TO KNOW YOUR VEHICLE • Quantity and distribution of the air introduced into the Adjusting The Fan Speed passenger compartment. Rotate the Blower Control knob to increase/decrease the • Climate Control system compressor. fan speed. • Air Recirculation. The speed is indicated by the eight Blower Control Indicator LEDs, located above the Blower Control knob, Cancelling all previous manual adjustments.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 SYNC Button Forced activation/deactivation can be selected by push- ing the Recirculation Control button. Push the “SYNC” button (LED illuminated) to correlate the passenger side air temperature with that of the driver When the On/Off button is pushed, the Climate Control side.
Page 124 122 GETTING TO KNOW YOUR VEHICLE • It is not recommended to use internal air recirculation NOTE: With the compressor off, air cannot be introduced when the outside temperature is low, since the win- to the passenger compartment with a temperature lower dows could mist up rapidly.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Rapid Window Demisting (MAX-Defrost function) When the function is activated, the AUTO button LED turns off. With the function activated, the only possible Push the MAX-defrost button to activate (LED on) the manual adjustments are pushing the A/C control button, windshield and side window demisting function.
Page 126 124 GETTING TO KNOW YOUR VEHICLE • The A/C compressor is off. Activation of this function is indicated by the rear defrost indicator light on the instrument panel turning on. The • The blower is off. function is automatically deactivated after 20 minutes. •...
Page 127: Windows
GETTING TO KNOW YOUR VEHICLE 125 System Maintenance In winter, the Climate Control system must be turned on at least once a month for approximately 10 minutes. Have the system inspected at an authorized dealership before the summer. NOTE: The system uses R-1234yf (refrigerant) which does not pollute the environment in the event of acciden- tal leakage.
Page 128 126 GETTING TO KNOW YOUR VEHICLE There are single window controls on each passenger door WARNING! trim panel, which operate the passenger door windows. The window controls will operate only when the ignition Never leave children unattended in a vehicle, and do is in the MAR/RUN or AVV/START position.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 AUTO-Down Feature — If Equipped To partially open the window, push the window switch and release it when you want the window to stop. To stop the window from going all the way down during the AUTO-down operation, pull up on the switch briefly when the when the window has reached the desired position.
Page 130 128 GETTING TO KNOW YOUR VEHICLE AUTO-Up Feature With Anti-Pinch Protection — If To partially close the window, lift the window switch and Equipped release it when you want the window to stop. NOTE: • If the window runs into any obstacle during auto- closure, it will reverse direction and then go back down.
Page 131: Power Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE 129 Reset AUTO-Up POWER SUNROOF — IF EQUIPPED Should the AUTO-Up feature stop working, the window The sunroof has two glass panels (the front one is probably needs to be reset. To reset Auto Up: operational and the rear one fixed) and is equipped with two manual operated sun blinds, front and rear.
Page 132 130 GETTING TO KNOW YOUR VEHICLE WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch.
Page 133: Opening The Sunroof
GETTING TO KNOW YOUR VEHICLE 131 Opening The Sunroof NOTE: During the open/close or vent operation any push on the switches will stop the closing of the panel. To retract the front panel to the open position, push the Open/Close button and the sunroof will fully open. The Wind Buffeting sunroof can be stopped in any position by pushing the Wind buffeting can be described as the perception of...
Page 134: Anti-Pinch Safety Device
132 GETTING TO KNOW YOUR VEHICLE Anti-Pinch Safety Device This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs.
Page 135: Power Sunroof Relearn Procedure
GETTING TO KNOW YOUR VEHICLE 133 3. Bring the ignition to the position MAR/RUN. CAUTION! 4. Pull the Open/Close button and hold it for at least 10 • When refitting sunroof, be careful to avoid fingers, seconds, after which you should feel the mechanical scarves, ties and items of clothing from getting stop of the electric motor of the roof.
Page 136 134 GETTING TO KNOW YOUR VEHICLE 1. Pull the hood release lever located under the drivers side of the instrument panel. Safety Latch Location 4. Remove the support rod from the locking tab and insert it into the seat located on the underside of the Hood Release Lever hood.
Page 137: Closing
GETTING TO KNOW YOUR VEHICLE 135 NOTE: • Before lifting the hood, check that the wiper arms are not in motion and not in the lifted position. • While lifting the hood, use both hands. • Vehicle must be at a stop and the automatic transmis- sion must be in park.
Page 138: Liftgate
136 GETTING TO KNOW YOUR VEHICLE Opening CAUTION! Opening From Outside To prevent possible damage, do not slam the hood to To unlock the Liftgate from the outside, squeeze the close it. Lower hood to approximately 12 in (30 cm) Electronic Liftgate Release and pull the Liftgate open and drop the hood to close.
Page 139 GETTING TO KNOW YOUR VEHICLE 137 Internal Emergency Release Proceed as follows: 1. Lower the headrests and tilt the seatbacks. Electronic Liftgate Release twice and the interior dome light will illuminate. The interior dome light will turn off automatically by closing the Liftgate.
Page 140: Closing
138 GETTING TO KNOW YOUR VEHICLE 3. Insert the screwdriver into the release tab slot to trigger the release tab of the Liftgate. Liftgate Closing Handle NOTE: Before closing the liftgate, make sure to be in possession of the key because the liftgate will be locked 2 —...
Page 141: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE 139 Cargo Area Features Access To The Loading Floor Cargo Load Floor — If Equipped To access the double load compartment, proceed as follows: The vehicle is equipped with a load floor that can be 1.
Page 142 140 GETTING TO KNOW YOUR VEHICLE 2. Place the desired objects inside the compartment. CAUTION! 3. Reposition the load floor. The load floor must be arranged in a central position with respect to cargo area. Displacement Load Floor To position the load from the lower to the upper position, proceed as follows: 1.
Page 143 GETTING TO KNOW YOUR VEHICLE 141 Anchoring Of The Load Cargo Box — If Equipped The cargo tie-downs, located on the trim panels around The cargo area contains a preformed cargo box that can the cargo area floor, should be used to safely secure loads be used for the storage of objects that allows you to when the vehicle is moving.
Page 144: Internal Equipment
142 GETTING TO KNOW YOUR VEHICLE NOTE: The cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg). INTERNAL EQUIPMENT Glove Compartments The glove compartments is located on the passengers side of the instrument panel. Upper Glove Compartment To open the upper compartment, push in the button located on the bottom side of the upper door.
Page 145: Sun Visors "Slide-On-Rod
GETTING TO KNOW YOUR VEHICLE 143 • The glove compartments should be completely closed while the vehicle is in motion. Sun Visors “Slide-On-Rod” Sun visors are located on both sides of the rearview mirror. The visors can be lowered or moved to the side to help block sunlight from entering the windshield or door glass.
Page 146 144 GETTING TO KNOW YOUR VEHICLE 1. Place the sun visor against the door glass by detaching it from the hook and turning it toward the side window. 2. Slide the visor. 3. Slide out the sun visor extender. Sun Visor Mirror Cover The visors also have illuminated vanity mirrors to allow use in low light conditions.
Page 147: Power Outlets
GETTING TO KNOW YOUR VEHICLE 145 Power Outlets NOTE: The power outlet can be changed to “battery” powered all the time by switching the power outlet The front power outlet is located under the center stack of Engine Compartment Fuses/Distribution Unit fuse from the instrument panel.
Page 148 146 GETTING TO KNOW YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of outlet power from the vehicle’s battery, even when not in should be inserted into any 12 Volt outlet.
Page 149: Cigar Lighter - Optional
GETTING TO KNOW YOUR VEHICLE 147 Cigar Lighter — Optional After a few seconds, the lighter automatically returns to its initial position and is ready to be used. NOTE: Cigar lighters can be purchased at an authorized dealer through MOPAR parts. To ensure proper cigar lighter WARNING! operation, a MOPAR knob and element must be used.
Page 150: Ashtray - If Equipped
148 GETTING TO KNOW YOUR VEHICLE Ashtray — If Equipped Front Armrest The front armrest is located between the front seats. NOTE: Ashtrays can be purchased at an authorized dealer through MOPAR parts. The armrest can be adjusted by moving it in the direction indicated by the arrows.
Page 151 GETTING TO KNOW YOUR VEHICLE 149 WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Storage Compartment Push the storage handle and lift up the armrest to access the storage compartment.
Page 152: Cupholders
150 GETTING TO KNOW YOUR VEHICLE Cupholders Grab Handles There are two cupholders for the front seat passengers, The Grab Handles are located immediately above the located in the center console. doors. The rear handles are equipped with hooks for dress hangers.
Page 153: Roof Luggage Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE 151 ROOF LUGGAGE RACK — IF EQUIPPED Do not use the sunroof when using the crossbars. Your vehicle may be equipped with a Roof Luggage Rack CAUTION! for transporting accessories. • To avoid damage to the Roof Luggage Rack and Crossbars should always be used whenever cargo is vehicle, do not exceed the maximum roof rack load placed on the Roof Luggage Rack.
Page 154 152 GETTING TO KNOW YOUR VEHICLE WARNING! Roof rack cargo must be securely tied down before driving your vehicle. Improperly secured loads may fall off the vehicle, particularly at high speeds, re- sulting in personal injury or property damage. Fol- low the Roof Luggage Rack warnings and cautions when carrying cargo on your roof rack.
Page 155 GETTING TO KNOW YOUR INSTRUMENT CLUSTER CONTENTS ▫ EVIC Main Menu .....162 INSTRUMENT CLUSTER ....154 ONBOARD DIAGNOSTIC SYSTEM (OBD II) .
Page 156: Instrument Cluster
154 GETTING TO KNOW YOUR INSTRUMENT CLUSTER INSTRUMENT CLUSTER...
Page 157 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 155 1. Speedometer 4. Engine Coolant Temperature • Indicates the speed of the car • The temperature gauge in the EVIC displays the temperature of the engine coolant and starts provid- 2. Fuel Level Gauge ing indications when the coolant temperature ex- •...
Page 158: Onboard Diagnostic System (Obd Ii)
156 GETTING TO KNOW YOUR INSTRUMENT CLUSTER ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 159: Electronic Vehicle Information Center (Evic)
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 157 access this information to assist with the diagnosis and For further information, refer to “Privacy Practices — If service of your vehicle and emissions system. Equipped With Uconnect 8.4 Radio” and “Uconnect CyberSecurity” in “All About Uconnect Access” in your WARNING! Owner’s Manual Radio Supplement and “Cybersecurity”...
Page 160: Mapping And Reconfigurable Zone Display (Evic) - If Equipped
158 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Mapping And Reconfigurable Zone Display (EVIC) – Date (Centered) — If Equipped – Compass (Centered) – Time (Centered) – External Temp. (Centered) • Zone (2) – Actual Gear Indication (Centered) – PRND (Centered) •...
Page 161 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 159 • Zone (4A) • Zone (6) – Title (Centered) – Odometer Digits (Left) – Browsing Arrows (Left) – Odometer Unit (Right) – Title Number (Right) – Cruise Control Speed Set (Center) – Speed Buzzer (Right) •...
Page 162: Evic Control Buttons
160 GETTING TO KNOW YOUR INSTRUMENT CLUSTER EVIC Control Buttons The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: EVIC Control Buttons 1 — Arrow Up/Down Scroll Through Menus And Submenus 2 —...
Page 163: Engine Oil Change Reset
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 161 • UP Arrow Button • OK Button Push and release the UP arrow button to scroll The OK button may be used for the following: upward through main menu Select submenus. Reset (hold) •...
Page 164: Evic Main Menu
162 GETTING TO KNOW YOUR INSTRUMENT CLUSTER position. To reset the oil change indicator system (after NOTE: performing the scheduled maintenance), refer to the • The display mode of the menu items varies depending following procedure. on the type of display. 1.
Page 165 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 163 • Drive Mode Selector – Units – Auto Mode – Clock & Date – Sport Mode – Security – Traction/All Weather Mode – Safety & Assistance – Lights • Vehicle Info – Doors & Locks –...
Page 166 164 GETTING TO KNOW YOUR INSTRUMENT CLUSTER • Trip A Drive Mode Selector – View and change Trip A distance (miles or km) This EVIC menu/submenu items allows you to view and – View and change travel time A (hours/minutes/ select information about the Drive Mode : seconds •...
Page 167 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 165 Vehicle Info Driver Assist Push and release the UP or DOWN arrow button This menu item allows you to change the settings ( No- until Vehicle Info is highlighted in the EVIC. Push tice LaneSense and Intensity LaneSense ) relating to the and release the RIGHT arrow button and Coolant...
Page 168 166 GETTING TO KNOW YOUR INSTRUMENT CLUSTER The information displayed is: The background color of the display varies according to the priorities of the failure: • “Radio (AM or FM)” • Failed Messages with low priority displays in yellow • View Radio Station Name (if equipped), frequency, •...
Page 169 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 167 Refer to “Uconnect Settings” in “Multimedia” for more disconnected), the active telephone calls/incoming/on information. hold, and the management of double calls (first incom- ing second waiting, etc.). Display • Navigation Repetition: Allows you to view, on the By selecting Display, you can access the following instrument cluster display, information relating to the settings:...
Page 170 168 GETTING TO KNOW YOUR INSTRUMENT CLUSTER • Seat Belt Buzzer: This function is only viewable when Clock and Date the Seat Belt Reminder (SBR) system is active. By selecting the item clock and date, you can adjust the • Hill Start Assist: Activation/Deactivation of the Hill clock.
Page 171 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 169 • Auto Wipers: Enabling/disabling the automatic opera- • Headlight Sensor: Adjust the sensitivity of headlight tion of wipers in the event of rain brightness • LaneSense Warning: A selection of the readiness of •...
Page 172: Trip Computer
170 GETTING TO KNOW YOUR INSTRUMENT CLUSTER • Unlock On First Press Of Key Fob (vehicles without Doors And Locks Passive Entry): allows you to choose whether to un- By selecting the item Doors & Locks, you can make the lock all the doors or only the driver’s side door on the following adjustments: first push of the UNLOCK button on the RKE...
Page 173: Quantities Displayed
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 171 Both trips can be reset (reset - start of a new trip). To Represents the average speed since the start of the new trip. perform a reset, push and hold the OK button on the Travel Time steering wheel controls.
Page 174: Warning And Indicator Lights
172 GETTING TO KNOW YOUR INSTRUMENT CLUSTER WARNING AND INDICATOR LIGHTS IMPORTANT: The warning / indicator lights switch on in the instrument panel together with a dedicated mes- sage and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases.
Page 175: Red Telltale Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 173 Red Telltale Indicator Lights Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN.
Page 176 174 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check.
Page 177 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 175 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reser- voir.
Page 178 176 GETTING TO KNOW YOUR INSTRUMENT CLUSTER The light will remain on until the cause is corrected. Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- Operation of the Brake Warning Light can be checked by tions.
Page 179 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 177 Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the en- gine is running, there may be a malfunction with the charging system. Contact your autho- rized dealer as soon as possible.
Page 180 178 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Coolant Temperature Warning Light Red Telltale What It Means Light Coolant Temperature Warning Light This light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
Page 181 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 179 Door Open Warning Light Red Telltale Light What It Means Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. • Driver’s Door Open • Passenger Door Open •...
Page 182 180 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Electric Power Steering Fail Warning — If Equipped Red Telltale What It Means Light Electric Power Steering Fail Warning — If Equipped This light is used to manage the electrical warning of the EPS (Power Steering System). Re- fer to “Power Steering”...
Page 183 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 181 Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns Do not operate the vehicle until the cause is corrected.
Page 184 182 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Vehicle Security Warning Light — If Equipped Red Telltale What It Means Light Vehicle Security Warning Light — If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
Page 185 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 183 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash de- pending on the nature of the problem.
Page 186: Yellow Telltale Indicator Lights
184 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Yellow Telltale Indicator Lights Low Fuel Indicator Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 1.3–1.8 gal (5–7 L) this light will turn on, and re- main on until fuel is added.
Page 187 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 185 Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 188 186 GETTING TO KNOW YOUR INSTRUMENT CLUSTER CAUTION! WARNING! Prolonged driving with the Malfunction Indicator A malfunctioning catalytic converter, as referenced Light (MIL) on could cause damage to the engine above, can reach higher temperatures than in normal control system. It also could affect fuel economy and operating conditions.
Page 189 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 187 Wait To Start Light — If Equipped Yellow Telltale What It Means Light Wait To Start Light The “Wait To Start” telltale will illuminate for approximately two seconds when the ignition is turned to the RUN position. It’s duration may be longer based on colder operating condi- tions.
Page 190 188 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Vehicle Security Indicator Light Yellow Telltale What It Means Light Vehicle Security Indicator Light This indicator will illuminate when the Vehicle Security Alarm system has detected an at- tempt was made to break into the vehicle.
Page 191 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 189 Transmission Temperature Indicator Light Yellow Tell- What It Means tale Light Transmission Temperature Indicator Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 192 190 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Tire Pressure Monitoring Indicator Light Yellow Telltale What It Means Light Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 193 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 191 IMPORTANT: Do not continue driving with one or more Accordingly, when the low tire pressure telltale illumi- flat tires as handling may be compromised. Stop the nates, you should stop and check your tires as soon as vehicle, avoiding sharp braking and steering.
Page 194 192 GETTING TO KNOW YOUR INSTRUMENT CLUSTER illuminated. This sequence will continue upon subse- CAUTION! quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- The TPMS has been optimized for the original tem may not be able to detect or signal low tire pressure equipment tires and wheels.
Page 195 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 193 Stop Light Failure Indicator Light Yellow Telltale What It Means Light Stop Light Failure Indicator Light This light will illuminate if one or more of the stop light bulb fails. The failure relating to this light could be: •...
Page 196 194 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Service Warning Indicator Light – If Equipped Yellow Telltale What It Means Light Service Warning Indicator Light The “Scheduled Servicing Plan” includes vehicle maintenance at fixed intervals, refer to the Maintaining And Caring For your Vehicle chapter. This message is displayed automatically along with the warning light when the key is turned to MAR-ON - 1242 miles (2,000 km) before these deadlines and reappears every 124 miles (200 km).
Page 197 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 195 Service Stop/Start System Indicator Light — If Equipped Yellow Telltale What It Means Light Service Stop/Start System Indicator Light — If Equipped This telltale will turn on to indicate the Stop/Start system is not functioning properly and service is required.
Page 198 196 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the igni- tion switch is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 199 GETTING TO KNOW YOUR INSTRUMENT CLUSTER 197 Electronic Park Brake Fail Light Yellow Telltale What It Means Light Electronic Park Brake Fail Warning Light This telltale will turn on to indicate the Electronic Park Brake is not functioning properly and that service is required. Contact your authorized dealership. Exterior Bulb Failure Indicator Light Yellow Telltale What It Means...
Page 200 198 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the AVV/START position.
Page 201: Green Telltale Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 199 Electronic Stability Control (ESC) OFF Indicator Light Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. Green Telltale Indicator Lights Turn Signal Indicator Lights Green Tell- What It Means...
Page 202 200 GETTING TO KNOW YOUR INSTRUMENT CLUSTER Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light...
Page 203: Blue Telltale Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT CLUSTER 201 Cruise Control Engaged Indicator Light Green Telltale What It Means Light Cruise Control Engaged Indicator Light This light will turn on when the cruise control has been set to a certain speed. Blue Telltale Indicator Lights High Beam Indicator Light Blue Telltale What It Means...
Page 205 SAFETY CONTENTS ▫ Electronic Roll Mitigation (ERM) ..214 BRAKE SYSTEM ..... . .205 ▫...
Page 206 204 SAFETY ▫ Exhaust Gas ......271 ▫ Periodic Safety Checks You Should Make Outside The Vehicle ......274 ▫...
Page 207: Brake System
SAFETY 205 BRAKE SYSTEM WARNING! Your vehicle is equipped with dual hydraulic brake • Riding the brakes can lead to brake failure and systems. If either of the two hydraulic systems loses possibly a collision. Driving with your foot resting normal capability, the remaining system will still func- or riding on the brake pedal can result in abnor- tion.
Page 208: Electronic Brake Control System
206 SAFETY ELECTRONIC BRAKE CONTROL SYSTEM Brake System Warning Light Your vehicle is equipped with an advanced Electronic The red “Brake System Warning Light” will turn on when Brake Control system (EBC). This system includes Elec- the ignition switch is turned to the ON position and may tronic Brake Force Distribution (EBD), Anti-Lock Brake stay on for as long as four seconds.
Page 209 SAFETY 207 and driven. During this self-check, you may hear a slight WARNING! clicking sound as well as some related motor noises. • The ABS contains sophisticated electronic equip- ABS is activated during braking when the system detects ment that may be susceptible to interference one or more wheels begins to lock.
Page 210: Anti-Lock Brake Warning Light
208 SAFETY service is required. However, the conventional brake WARNING! (Continued) system will continue to operate normally if the “Brake • The ABS cannot prevent collisions, including those System Warning Light” is not on. resulting from excessive speed in turns, following If the “Anti-Lock Brake Warning Light”...
Page 211: Hill Start Assist (Hsa)
SAFETY 209 benefit of the system, you must apply continuous brak- Hill Start Assist (HSA) ing pressure during the stopping sequence, (do not The HSA system is designed to mitigate roll back from a “pump” the brakes). Do not reduce brake pedal pressure complete stop while on an incline.
Page 212 210 SAFETY • The gear selection must match vehicle uphill direction WARNING! (Continued) (i.e., vehicle facing uphill is in forward gear; vehicle brake operation to ensure safe operation of the ve- backing uphill is in REVERSE gear). hicle under all road conditions. Your complete atten- •...
Page 213: Traction Control System (Tcs)
SAFETY 211 • If disabling HSA using Uconnect Settings, refer to 7. Rotate the steering wheel back to center and then an “Uconnect Settings” in the “Multimedia” section for additional slightly more than one-half turn to the further information. right. For vehicles not equipped with the EVIC, perform the 8.
Page 214: Electronic Stability Control (Esc)
212 SAFETY one wheel on a driven axle is spinning faster than the the intended path, ESC applies the brake of the appro- other, the system will apply the brake of the spinning priate wheel to assist in counteracting the oversteer or wheel.
Page 215 SAFETY 213 WARNING! WARNING! (Continued) hydroplaning. ESC also cannot prevent accidents When in “Partial Off” mode, the TCS functionality of resulting from loss of vehicle control due to inap- ESC, (except for the limited slip feature described in propriate driver input for the conditions. Only a the TCS section), has been disabled and the “ESC Off safe, attentive, and skillful driver can prevent acci- Indicator Light”...
Page 216: Electronic Roll Mitigation (Erm)
214 SAFETY cannot prevent wheel lift due to other factors, such as WARNING! (Continued) road conditions, leaving the roadway, or striking objects ESC performance. Improperly inflated and un- or other vehicles. evenly worn tires may also degrade ESC perfor- NOTE: ERM is disabled anytime the ESC is in “Full Off” mance.
Page 217: Dynamic Steering Torque (Dst)
SAFETY 215 Dynamic Steering Torque (DST) OCCUPANT RESTRAINT SYSTEMS Dynamic Steering Torque is a feature of the ESC and EPS Some of the most important safety features in your modules that provides torque at the steering wheel for vehicle are the restraint systems: certain driving conditions in which the ESC module is •...
Page 218 216 SAFETY 2. If a child from 2 to 12 years old (not in a rear-facing 6. All occupants should always wear their lap and child restraint) must ride in the front passenger seat, shoulder belts properly. move the seat as far back as possible and use the 7.
Page 219: Seat Belt Systems
SAFETY 217 ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should • Never place a rear-facing child restraint in front of be belted at all times. an air bag. A deploying Passenger Advanced Front Enhanced Seat Belt Use Reminder System Air Bag can cause death or serious injury to a child (BeltAlert)
Page 220 218 SAFETY front passenger seat BeltAlert) is unbuckled when the sequence may repeat based on vehicle speed until the ignition switch is first turned to the AVV/START or driver and occupied outboard front seat passenger seat MAR/ RUN position the Seat Belt Reminder Light will belts are buckled.
Page 221 SAFETY 219 BeltAlert can be activated or deactivated by your autho- WARNING! rized dealer. FCA US LLC does not recommend deacti- • Relying on the air bags alone could lead to more vating BeltAlert. severe injuries in a collision. The air bags work NOTE: If BeltAlert has been deactivated and the driver with your seat belt to restrain you properly.
Page 222 220 SAFETY WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your • A lap belt worn too high can increase the risk of vehicle that is not equipped with seats and seat injury in a collision. The seat belt forces won’t be at belts.
Page 223 SAFETY 221 WARNING! (Continued) WARNING! (Continued) • A seat belt that is too loose will not protect you • A frayed or torn seat belt could rip apart in a properly. In a sudden stop, you could move too far collision and leave you with no protection.
Page 224 222 SAFETY Pulling Out The Latch Plate Inserting Latch Plate Into Buckle 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 225 SAFETY 223 Positioning The Lap Belt Releasing The Seat Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfort- slack in the lap belt portion, pull up on the shoulder able and not resting on your neck.
Page 226 224 SAFETY position. If necessary, slide the latch plate down the Adjustable Upper Shoulder Belt Anchorage webbing to allow the seat belt to retract fully. In the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to Lap/Shoulder Belt Untwisting Procedure position the seat belt away from your neck.
Page 227 SAFETY 225 As a guide, if you are shorter than average, you will NOTE: The adjustable upper shoulder belt anchorage is prefer the shoulder belt anchorage in a lower position, equipped with an Easy Up feature. This feature allows and if you are taller than average, you will prefer the the shoulder belt anchorage to be adjusted in the upward shoulder belt anchorage in a higher position.
Page 228 226 SAFETY 2. Grasp the mini-latch plate and pull the seat belt over 4. When the seat belt is long enough to fit, insert the the seat. mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap.
Page 229 SAFETY 227 8. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retrac- tor will withdraw any slack in the seat belt. 9. To release the seat belt, push the red button on the buckle.
Page 230 228 SAFETY Seat Belts And Pregnant Women WARNING! • If the mini-latch plate and mini-buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 231 SAFETY 229 Position the lap belt snug and low below the abdomen The pretensioners are triggered by the Occupant Re- and across the strong bones of the hips. Place the straint Controller (ORC). Like the air bags, the preten- shoulder belt across the chest and away from the neck. sioners are single use items.
Page 232 230 SAFETY Restraints” section of this manual. The table below If the passenger seating position is equipped with an defines the type of feature for each seating position. ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR.
Page 233 SAFETY 231 How To Disengage The Automatic Locking Mode WARNING! Unbuckle the combination lap/shoulder belt and allow it • Never place a rear-facing child restraint in front of to retract completely to disengage the Automatic Locking an air bag. A deploying Passenger Advanced Front Mode and activate the vehicle sensitive (emergency) Air Bag can cause death or serious injury to a child locking mode.
Page 234: Supplemental Restraint System (Srs)
232 SAFETY • Supplemental Side Air Bags WARNING! (Continued) • Supplemental Knee Air Bags only used to install rear-facing or forward-facing child restraints that have a harness for restraining • Front and Side Impact Sensors the child. • Seat Belt Pretensioners Supplemental Restraint System (SRS) •...
Page 235 SAFETY 233 WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
Page 236 234 SAFETY Advanced Front Air Bag Features WARNING! The Advanced Front Air Bag system has multistage • No objects should be placed over or near the air driver and front passenger air bags. This system provides bag on the instrument panel or steering wheel output appropriate to the severity and type of collision as because any such objects could cause harm if the determined by the Occupant Restraint Controller (ORC),...
Page 237 SAFETY 235 On the other hand, depending on the type and location of WARNING! (Continued) impact, Advanced Front Air Bags may deploy in crashes • Relying on the air bags alone could lead to more with little vehicle front-end damage but that produce a severe injuries in a collision.
Page 238 236 SAFETY way as the air bags inflate to their full size. The Advanced Supplemental Driver Knee Air Bag Front Air Bags fully inflate in less time than it takes to This vehicle is equipped with a Supplemental Driver blink your eyes. The air bags then quickly deflate while Knee Air Bag mounted in the instrument panel below the helping to restrain the driver and front passenger.
Page 239 SAFETY 237 When the SAB deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 240 238 SAFETY 2. Supplemental Side Air Bag Inflatable Curtains (SABICs) are located above the side windows. The trim covering the SABICs is labeled “SRS AIRBAG” or “AIRBAG.” Supplemental Side Air Bag Inflatable Curtain (SABIC) SABICs may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and...
Page 241 SAFETY 239 The SABICs deploy downward, covering the side win- WARNING! dows. An inflating SABIC pushes the outside edge of the • Your vehicle is equipped with left and right trim out of the way and covers the window. The SABICs inflate with enough force to injure occupants if they are Supplemental Side Air Bag Inflatable Curtains not belted and seated properly, or if items are positioned...
Page 242 240 SAFETY The SABICs and SABs (“Side Air Bags”) are designed to Seat belts (and child restraints where appropriate) are activate in certain side impacts and certain rollover necessary for your protection in all collisions. They also events. The Occupant Restraint Controller (“ORC”) de- help keep you in position, away from inflating Side Air termines whether the deployment of the Side Air Bags in Bags.
Page 243 SAFETY 241 deploys the left Side Air Bags only and a right side WARNING! (Continued) impact deploys the right Side Air Bags only. • Relying on the Side Air Bags alone could lead to The Side Air Bags will not deploy in all side collisions, more severe injuries in a collision.
Page 244 242 SAFETY event may be in progress and whether deployment is deploy and unfold. The abrasions are similar to fric- appropriate. In the event the vehicle experiences a roll- tion rope burns or those you might get sliding along a over or near rollover event, and deployment of the Side carpet or gymnasium floor.
Page 245 SAFETY 243 Do not drive your vehicle after the air bags have de- Enhanced Accident Response System ployed. If you are involved in another collision, the air In the event of an impact, if the communication network bags will not be in place to protect you. remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine WARNING!
Page 246 244 SAFETY • Turn off the Fuel Pump Heater. move your vehicle to the side of the road, you must follow the system reset procedure. • Turn off the HVAC Blower Motor. • Close the HVAC Circulation Door. Customer Action Customer Will See 1.
Page 247 SAFETY 245 If a reset procedure step is not completed within 60 Customer Action Customer Will See seconds, then the turn signal lights will blink and the 5. Turn Right Turn Signal Right Turn Light Is ON reset procedure must be performed again in order to be Switch ON.
Page 248 246 SAFETY The ORC contains a backup power supply system that free, if any of the following occurs, have an authorized may deploy the air bags even if the battery loses power or dealer service the air bag system immediately. it becomes disconnected prior to deployment.
Page 249 SAFETY 247 Redundant Air Bag Warning Light comes on intermittently WARNING! or remains on while driving have an authorized dealer service the vehicle immediately. For additional information Ignoring the Air Bag Warning Light in your instru- regarding the Redundant Air Bag Warning Light refer to the ment panel could mean you won’t have the air bags “Instrument Panel”...
Page 250 248 SAFETY Event Data Recorder (EDR) WARNING! (Continued) This vehicle is equipped with an event data recorder • It is dangerous to try to repair any part of the air (EDR). The main purpose of an EDR is to record, in bag system yourself.
Page 251: Child Restraints
SAFETY 249 These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all times, including babies and children. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs;...
Page 252 250 SAFETY Before buying any restraint system, make sure that it has WARNING! a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install In a collision, an unrestrained child can become a it in the vehicle where you will use it.
Page 253 SAFETY 251 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convertible younger and who have not reached the Child Restraint, facing rearward in the height or weight limits of their child rear seat of the vehicle...
Page 254 252 SAFETY Infants And Child Restraints WARNING! Safety experts recommend that children ride rear-facing • Never place a rear-facing child restraint in front of in the vehicle until they are two years old or until they an air bag. A deploying passenger Advanced Front reach either the height or weight limit of their rear-facing Air Bag can cause death or serious injury to a child child restraint.
Page 255 SAFETY 253 remain in a forward-facing child seat with a harness for WARNING! (Continued) as long as possible, up to the highest weight or height directions exactly when installing an infant or allowed by the child seat. child restraint. All children whose weight or height is above the •...
Page 256 254 SAFETY Children Too Large For Booster Seats 5. Can the child stay seated like this for the whole trip? Children who are large enough to wear the shoulder belt If the answer to any of these questions was “no,” then the comfortably, and whose legs are long enough to bend child still needs to use a booster seat in this vehicle.
Page 257 SAFETY 255 Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor Restraint Only...
Page 258 256 SAFETY Lower Anchors And Tethers For CHildren Your vehicle is equipped with the child restraint anchor- (LATCH) Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 259 SAFETY 257 LATCH Positions For Installing Child Restraints In This Vehicle • — Lower Anchorage Symbol 2 Anchorages Per Seating Position • — Top Tether Anchorage Symbol...
Page 260 258 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 261 SAFETY 259 Frequently Asked Questions About Installing Child Restraints With LATCH Can two child restraints be attached using Never “share” a LATCH anchorage with a common lower LATCH anchorage? two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child seat using the LATCH anchor-...
Page 262 260 SAFETY Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 263 SAFETY 261 Locating Tether Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower There are tether strap anchorages behind each anchorage and a way to tighten the connection to the rear seatback, near the floor.
Page 264 262 SAFETY Center Seat LATCH: To Install A LATCH-Compatible Child Restraint If the selected seating position has a Switchable Auto- WARNING! matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below. See the section • Do not install a child restraint in the center posi- “Installing Child Restraints Using the Vehicle Seat Belt”...
Page 265 SAFETY 263 3. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seat Belt: restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child 4.
Page 266 264 SAFETY Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of the re- equipped with a Switchable Automatic Locking Retractor straint.
Page 267 SAFETY 265 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle • ALR = Switchable Automatic Locking Retractor • = Top Tether Anchorage Symbol...
Page 268 266 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to with the seat belt to attach a for-...
Page 269 SAFETY 267 Installing A Child Restraint With A Switchable 4. Pull on the webbing to make the lap portion tight Automatic Locking Retractor (ALR) against the child seat. 1. Place the child seat in the center of the seating 5. To lock the seat belt, pull down on the shoulder part of position.
Page 270 268 SAFETY 8. If the child restraint has a top tether strap and the Installing Child Restraints Using The Top Tether seating position has a top tether anchorage, connect Anchorage: the tether strap to the anchorage and tighten the tether strap.
Page 271 SAFETY 269 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 272: Transporting Pets
270 SAFETY SAFETY TIPS WARNING! Transporting Passengers • An incorrectly anchored tether strap could lead to NEVER TRANSPORT PASSENGERS IN THE CARGO increased head motion and possible injury to the AREA. child. Use only the anchorage position directly behind the child seat to secure a child restraint top WARNING! tether strap.
Page 273 SAFETY 271 Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle. Set the monoxide (CO), which is colorless and odorless.
Page 274 272 SAFETY Safety Checks You Should Make Inside The soon as possible. This light will illuminate with a Vehicle single chime when a fault with the Air Bag Warning Light has been detected, it will stay on until the fault Seat Belts is cleared.
Page 275 SAFETY 273 WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 276 274 SAFETY Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 277 STARTING AND OPERATING CONTENTS ▫ Auto Park Brake ..... .289 STARTING THE ENGINE ....279 ▫...
Page 278 276 STARTING AND OPERATING ▫ Key Ignition Park Interlock....307 ▫ Brake Control ......314 ▫...
Page 279 STARTING AND OPERATING 277 ▫ Reformulated Gasoline ....343 LANESENSE — IF EQUIPPED ... . .328 ▫...
Page 280 278 STARTING AND OPERATING ▫ Trailer Towing Weights DRIVING THROUGH WATER ... . .354 (Maximum Trailer Weight Ratings) ..362 ▫ Flowing/Rising Water ....354 ▫...
Page 281: Starting The Engine
STARTING AND OPERATING 279 STARTING THE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the Keyless Enter-N-Go in the MAR/RUN mode. A inside and outside mirrors, fasten your seat belt, and if child could operate power windows, other controls, present, instruct all other occupants to buckle their seat or move the vehicle.
Page 282: Tip Start Feature
280 STARTING AND OPERATING 4. If the engine does not start, place the ignition in the Tip Start Feature STOP/OFF position and wait 10-15 seconds before Do not press the accelerator. Cycle the ignition switch attempting to restart the engine. briefly to the AVV/START position and release it.
Page 283: Cold Weather Operation
STARTING AND OPERATING 281 floor and hold it there. Crank the engine for no more than WARNING! (Continued) 15 seconds. This should clear any excess fuel in case the • Do not attempt to push or tow your vehicle to get it engine is flooded.
Page 284: Extended Park Starting
282 STARTING AND OPERATING Turbo engine below -20°F (-29°C) and for the 2.4L engine 2. Cycle the ignition in the START position and release it below -29°F (-34°C) and is recommended for the 2.4L when the engine starts. engine below -20°F (-29°C). 3.
Page 285: After Starting - Warming Up The Engine
STARTING AND OPERATING 283 After Starting — Warming Up The Engine 3. With the engine idling, place the ignition in the STOP/OFF position. Proceed as follows: 4. Remove the key from the ignition when the engine is • Travel slowly, letting the engine run at a reduced RPM, shut off.
Page 286: Turbocharger "Cool Down" - If Equipped
284 STARTING AND OPERATING When the ignition is in the STOP/OFF position, the ENGINE BREAK-IN RECOMMENDATIONS window switches remains active for three minutes. A long break-in period is not required for the engine and Opening a front door will cancel this function. drivetrain (transmission and axle) in your vehicle.
Page 287: Electric Park Brake (Epb)
STARTING AND OPERATING 285 The EPB switch is located in the center console. CAUTION! You can engage the EPB in two ways; Never use Non-Detergent Oil or Straight Mineral Oil • Manually, by pulling up on the park brake switch in the engine or damage may result.
Page 288 286 STARTING AND OPERATING while you apply the EPB, you may notice a small amount of brake pedal movement. The EPB can be applied even when the ignition switch is in the STOP/OFF position but the BRAKE warning lamp will not illuminate, how- ever, it can only be released when the ignition switch is in the MAR/RUN position.
Page 289 STARTING AND OPERATING 287 The EPB will be automatically released if the driver’s seat NOTE: belt is buckled and driver’s intention to start (in forward • When parking on a hill, it is important to turn the front or reverse direction) is recognized by the system wheels toward the curb on a downhill grade and away To release the EPB manually, the ignition switch must be from the curb on an uphill grade.
Page 290 288 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle (or • When leaving the vehicle, always remove the key in a location accessible to children), and do not fob from the ignition and lock your vehicle. If leave the ignition of a vehicle equipped with equipped with Keyless Enter-N-Go, always make Keyless Enter-N-Go in the ACC or ON/RUN mode.
Page 291: Auto Park Brake
STARTING AND OPERATING 289 CAUTION! WARNING! If the Brake System Warning Light remains on with Driving the vehicle with the parking brake engaged, the parking brake released, a brake system malfunc- or repeated use of the parking brake to slow the tion is indicated.
Page 292: Safehold
290 STARTING AND OPERATING • There is no attempt to depress the brake pedal or with a manual transmission, whenever the ignition switch is in the STOP/OFF position. Auto Park Brake is accelerator pedal. enabled and disabled by customer selection through the •...
Page 293: Brake Service Mode
STARTING AND OPERATING 291 SafeHold can be temporarily bypassed by pushing the your vehicle. This menu based system will guide you EPB Switch while the driver door is open and the brake through the steps necessary to retract the EPB actuator in pedal is pressed.
Page 294: Manual Transmission
292 STARTING AND OPERATING When brake service work is complete, the following steps MANUAL TRANSMISSION must be followed to reset the parking brake system to normal operation: WARNING! • Ensure the vehicle is at a standstill. You or others could be injured if you leave the vehicle unattended without having the parking •...
Page 295: Shifting
STARTING AND OPERATING 293 To shift the gears, press the clutch pedal to the floor and To engage REVERSE gear from the NEUTRAL position put the gear selector to the desired position (the diagram lift the REVERSE ring, located below the knob and for the engagement of the gears is displayed on the simultaneously move the lever to the left and then handle of the lever).
Page 296: Downshifting
294 STARTING AND OPERATING Manual Transmission Shift Speeds in MPH (KM/H) All Engines Gear Selection 2 to 3 3 to 4 4 to 5 5 to 6 Accel. 24 (39) 34 (55) 47 (76) 56 (90) Cruise 19 (31) 27 (43) 37 (60) 41 (66) Downshifting...
Page 297 STARTING AND OPERATING 295 Maximum Recommended Downshift Speeds CAUTION! (Continued) clutch damage, even if the clutch pedal is pressed. CAUTION! If transfer case is in low range the vehicle speeds to Failure to follow the maximum recommended down- cause engine and clutch damage are significantly shifting speeds may cause the engine to overspeed lower.
Page 298: Automatic Transmission
296 STARTING AND OPERATING rearward or forward. You must also press the brake pedal CAUTION! to shift the transmission out of PARK, or to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is If you skip a gear while downshifting or downshift stopped or moving at low speeds (refer to Brake/ at too high of a vehicle speed, these conditions may Transmission Shift Interlock System in this section).
Page 299 STARTING AND OPERATING 297 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 300: Gear Selector
298 STARTING AND OPERATING Gear Selector CAUTION! The transmission gear selector has PARK, REVERSE, NEU- Damage to the transmission may occur if the follow- TRAL, DRIVE, and AutoStick (+/-) shift positions. Manual ing precautions are not observed: shifts can be made using the AutoStick shift control (refer •...
Page 301 STARTING AND OPERATING 299 The transmission gear range (PRND) is displayed both beside the gear selector and in the Electronic Vehicle Information Center (EVIC). To select a gear range, press the gear selector lock button on the gear selector and move the lever rearward or forward.
Page 302: Gear Ranges
300 STARTING AND OPERATING DO NOT race the engine when shifting from PARK or When parking on a hill, apply the EPB before shifting the NEUTRAL into another gear range. transmission to PARK, otherwise the load on the transmis- sion locking mechanism may make it difficult to move the CAUTION! gear selector out of PARK.
Page 303 STARTING AND OPERATING 301 WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL • When leaving the vehicle, always make sure the if the engine speed is higher than idle speed. If ignition is in the STOP/OFF position, remove the your foot is not firmly pressing the brake pedal, the Key Fob from the vehicle, and lock the vehicle.
Page 304 302 STARTING AND OPERATING • Look at the transmission gear position display and CAUTION! verify that it indicates the PARK position (P). • Before moving the gear selector out of PARK, you • With the brake pedal released, verify that the gear must turn the ignition switch from the STOP/OFF selector will not move out of PARK.
Page 305 STARTING AND OPERATING 303 Drive (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the smoothest upshifts and down- ignition to coast down a hill. These are unsafe shifts, and the best fuel economy.
Page 306 304 STARTING AND OPERATING If the transmission temperature exceeds normal operat- AutoStick ing limits, the transmission controller may modify the AutoStick is a driver-interactive transmission feature transmission shift schedule, reduce engine torque, providing manual shift control, giving you more control and/or expand the range of torque converter clutch of the vehicle.
Page 307 STARTING AND OPERATING 305 • If a requested downshift would cause the engine to NOTE: In AutoStick mode, the transmission will only shift up or down when the driver moves the gear selector over-speed, that shift will not occur. rearward (+) or forward (-), except as described below. •...
Page 308: Transmission Limp Home Mode
306 STARTING AND OPERATING In the event of a momentary problem, the transmission WARNING! can be reset to regain all forward gears by performing the following steps: Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their 1.
Page 309: Starting And Operating
STARTING AND OPERATING 307 NOTE: Even if the transmission can be reset, we recom- removal) position. The key can only be removed from the mend that you visit your authorized dealer at your ignition when the ignition is in the STOP/OFF position, earliest possible convenience.
Page 310: Speed Control - If Equipped
308 STARTING AND OPERATING The brake pedal must also be pressed before pushing the button on the gear selector to shift from NEUTRAL into DRIVE or REVERSE when the vehicle is stopped or moving at low speeds. SPEED CONTROL — IF EQUIPPED When engaged, the Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
Page 311: Activation
STARTING AND OPERATING 309 NOTE: In order to ensure proper operation, the Speed WARNING! Control System has been designed to shut down if multiple Speed Control functions are operated at the Leaving the Electronic Speed Control system on same time. If this occurs, the Speed Control System can when not in use is dangerous.
Page 312: Deactivation
310 STARTING AND OPERATING Deactivation Varying The Speed A soft tap on the brake pedal, pushing the CANCEL To Increase Speed button, ESC intervention, Forward collision mitigation, When the Speed Control is set, you can increase speed by Electronic Park Brake Intervention, or normal brake pushing the SET + button.
Page 313 STARTING AND OPERATING 311 Metric Speed (km/h) U.S. Speed (mph) • Pushing the SET + button once will result in a 1 km/h • Pushing the SET - button once will result in a 1 mph increase in set speed. Each subsequent tap of the decrease in set speed.
Page 314: Accelerating For Passing
312 STARTING AND OPERATING Accelerating For Passing CAUTION! Push the accelerator as you would normally. When the All wheels must have the same size and type tires. pedal is released, the vehicle will return to the set speed. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit.
Page 315: Warning Messages
STARTING AND OPERATING 313 All Weather Mode – This mode offers increased traction control and stability control for low traction conditions such as driving on a dirt road or off road as well as wet and slippery roads. Sport Mode – This mode is designed to increase steering feedback to the driver with a slight increase in effort and changes the transmission shift schedules for more aggres- sive shifting.
Page 316: Brake Control - If Equipped
314 STARTING AND OPERATING • If the driver does not take action based upon these BRAKE CONTROL — IF EQUIPPED progressive warnings, then the system will provide a Brake Control limited level of active braking to help slow the vehicle The Brake Control system with mitigation provides the and mitigate the potential forward collision.
Page 317 STARTING AND OPERATING 315 If a Brake Control event begins at a speed below 20 mph When the system determines a collision with the vehicle (32 km/h), the system may provide the maximum brak- in front of you is no longer probable, the warning ing possible to mitigate the potential forward collision.
Page 318: Turning Brake Control On Or Off
316 STARTING AND OPERATING • The active braking is enabled only if the front seat belts • Changing the Brake Control status to “Off” deactivates are fastened. the system, so no warning or active braking will be available in case of a possible collision WARNING! •...
Page 319: Changing Brake Control Sensitivity
STARTING AND OPERATING 317 Changing Brake Control Sensitivity By changing the option to Near , the system will warn the driver of a possible accident with the vehicle ahead of By changing the settings on the menu of the Uconnect it when the latter is a reduced distance.
Page 320: Service Brake Control Warning
318 STARTING AND OPERATING Service Brake Control Warning The “Brake Control Front Radar Sensor Temporarily Blocked” message can sometimes be displayed while If the system turns off, and the EVIC displays: driving in highly reflective areas (i.e. tunnels with reflec- •...
Page 321: Precautions While Driving With Brake Control
STARTING AND OPERATING 319 • Passing of vehicles in an oncoming intersection NOTE: • If the “Brake Control Front Radar Sensor Temporarily The intervention of the system could be unexpected or delayed. The driver must therefore always pay particular Blocked” message occurs frequently (e.g. more than attention, while maintaining control of the car to drive in once on every trip) without any snow, rain, mud, or complete safety.
Page 322 320 STARTING AND OPERATING the presence of small vehicles such as bicycles or motor- cycles. Driving In The Vicinity Of A Curve Small Vehicles And/Or Not Aligned To The Lane Small Vehicles And/Or Not Aligned To The Lane The system is not able to detect the presence of vehicles that are in front of the car but placed outside the field of action of the radar sensor and could therefore not react in...
Page 323 STARTING AND OPERATING 321 Lane Changing Of Other Vehicles Passing Of Vehicles In An Oncoming Intersection Vehicles that suddenly change lane, while standing in the The system could temporarily react to a vehicle that traffic lane of their car and inside the field of action of the crossed the range of the radar sensor, in an oncoming radar sensor may cause the intervention of the system.
Page 324: General Information
322 STARTING AND OPERATING General Information PARKSENSE REAR PARK ASSIST — IF EQUIPPED This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications The ParkSense Rear Park Assist system provides visual Commission (FCC) rules and with Industry Canada and audible indications of the distance between the rear Standards RSS- GEN/210/220/310.
Page 325 STARTING AND OPERATING 323 obstacles from approximately 12 inches (30 cm) up to 59 Chime in (150 cm) from the rear fascia/bumper in the horizontal By shifting the vehicle in REVERSE and in the case of the direction, depending on the location, type and orienta- presence of a rear obstacle, an acoustic signal that varies tion of the obstacle.
Page 326: Enabling And Disabling Parksense
324 STARTING AND OPERATING When the system emits a beeping sound, the volume of If an obstacle is detected in the left and/or right rear the Uconnect system, if turned on, is automatically region, the display will show a single flashing arc in the lowered by ParkSense.
Page 327: Service The Rear Park Assist System
STARTING AND OPERATING 325 approximately five seconds. Refer to “Electronic Vehicle CAUTION! Information Center (EVIC)” in “Getting To Know Your Instrument Panel” for further information. When the After turning off the ignition, the ParkSense remains gear selector is moved to REVERSE and the system is in this setting until the next key cycle, even in the disabled, the EVIC will display the “PARKSENSE OFF”...
Page 328: Parksense System Usage Precautions
326 STARTING AND OPERATING REVERSE and the system has detected a faulted condi- ParkSense System Usage Precautions tion, the EVIC will display the PARK ASSIST UNAVAIL- NOTE: ABLE WIPE REAR SENSORS or PARKSENSE UN- • Ensure that the outer surface and the underside of the AVAILABLE SERVICE REQUIRED message for as long as the vehicle is in REVERSE.
Page 329 STARTING AND OPERATING 327 • Objects such as bicycle carriers, etc., must not be WARNING! placed within 12 inches (30 cm) from the rear fascia/ • Drivers must be careful when backing up even bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a when using ParkSense.
Page 330: Lanesense - If Equipped
328 STARTING AND OPERATING When both lane markings are detected and the driver WARNING! (Continued) unintentionally drifts out of the lane (no turn signal could detect the ball mount and hitch ball assem- applied), the LaneSense system provides a haptic warn- bly, depending on its size and shape, giving a false ing in the form of torque applied to the steering wheel to indication that an obstacle is behind the vehicle.
Page 331: Turning Lanesense On Or Off
STARTING AND OPERATING 329 NOTE: When operating conditions have been met, the NOTE: The LaneSense system will retain the last system LaneSense system will monitor if the driver’s hands are state ON or OFF from the last ignition cycle when the on the steering wheel and provides an audible warning ignition is changed to the ON/RUN position.
Page 332 330 STARTING AND OPERATING • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the LaneSense indicator changes from solid white to flashing yellow.
Page 333 STARTING AND OPERATING 331 NOTE: The LaneSense system operates with the similar behavior for a right lane departure when only the right lane marking has been detected. Left Lane Departure — Both Lanes Detected • When the LaneSense system is ON, the lane lines turn from gray to white to indicate that both of the lane markings have been detected.
Page 334 332 STARTING AND OPERATING • For example: If approaching the left side of the lane • When the LaneSense system senses the lane has been the steering wheel will turn to the right. approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow.
Page 335: Changing Lanesense Status
STARTING AND OPERATING 333 Changing LaneSense Status The LaneSense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity (early/late) that you can configure through the Uconnect system screen. Refer to “Uconnect Settings” in “Multime- dia”...
Page 336: Parkview Rear Back Up Camera - If Equipped
334 STARTING AND OPERATING PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED The ParkView Rear Back Up Camera that allows you to see an on-screen image of your vehicle’s rear surround- ings when the gear selector is put into REVERSE. The image will be displayed on the touchscreen display along with a note to “check entire surroundings”...
Page 337 STARTING AND OPERATING 335 REVERSE unless the vehicle speed exceeds 8 mph When enabled, fixed guide lines are overlaid on the (13 km/h), the vehicle is shifted into PARK or the ignition image to illustrate the width of the vehicle. is switched to the STOP/OFF position.
Page 338: Tire Pressure Monitoring System (Tpms)
336 STARTING AND OPERATING NOTE: If snow, ice, mud, or any foreign substance builds CAUTION! up on the camera lens, clean the lens, rinse with water, • To avoid vehicle damage, ParkView should only be and dry with a soft cloth. Do not cover the lens. used as a parking aid.
Page 339 STARTING AND OPERATING 337 The tire pressure will vary with temperature by about 1 The TPMS will continue to warn the driver of low tire psi (7 kPa) for every 12° F (6.5° C). This means that when pressure as long as the condition exists, and will not turn the outside temperature decreases, the tire pressure will off until the tire pressure is at or above the recommended decrease.
Page 340 338 STARTING AND OPERATING pressure is sufficiently low enough to turn on the Tire CAUTION! (Continued) Pressure Monitoring Telltale Light. Driving the vehicle sensor damage. Using aftermarket tire sealants may may cause the tire pressure to rise to approximately 27 cause the Tire Pressure Monitoring System (TPMS) psi (186 kPa), but the Tire Pressure Monitoring Telltale sensor to become inoperable.
Page 341: Base System
STARTING AND OPERATING 339 • The TPMS should not be used as a tire pressure gauge Base System while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes This is the TPMS warning indicator located in the instrument cluster.
Page 342 340 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings the “Service Tire Pressure Monitoring System” text mes- sage will display. If the ignition key is cycled, this The Tire Pressure Monitoring Telltale Light will illumi- sequence will repeat providing the system fault still nate in the instrument cluster, an acoustic signal will be exists.
Page 343: General Information
STARTING AND OPERATING 341 • Once you repair or replace the original road tire and NOTE: Your vehicle may be equipped with a compact spare wheel and tire assembly. reinstall it on the vehicle in place of the compact spare tire, the TPMS will update automatically and the Tire •...
Page 344: Fuel Requirements
342 STARTING AND OPERATING NOTE: Changes or modifications not expressly approved While operating on gasoline with an octane number of by the party responsible for compliance could void the 87, hearing a light knocking sound from the engine is not user’s authority to operate the equipment.
Page 345: 2.4L Engine
STARTING AND OPERATING 343 2.4L Engine Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- All available gasoline engines are designed ering service for the vehicle. to meet all emissions regulations and pro- vide excellent fuel economy and perfor- Reformulated Gasoline...
Page 346: Gasoline/Oxygenate Blends
344 STARTING AND OPERATING Gasoline/Oxygenate Blends Problems that result from using gasoline containing more than 15% ethanol (E-15) or gasoline containing methanol Some fuel suppliers blend unleaded gasoline with oxy- are not the responsibility of the manufacturer and may genates such as ethanol. void or not be covered under New Vehicle Limited Warranty.
Page 347: Mmt In Gasoline
STARTING AND OPERATING 345 If a Non-FFV vehicle is inadvertently fueled with E-85 without MMT be used in your vehicle. The MMT content fuel, the engine will have some or all of these symptoms: of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether •...
Page 348: Fuel System Cautions
346 STARTING AND OPERATING Indiscriminate use of fuel system cleaning agents should CAUTION! (Continued) be avoided. Many of these materials intended for gum some light smoke, your engine may be out of tune and varnish removal may contain active solvents or or malfunctioning and may require immediate ser- similar ingredients.
Page 349: Carbon Monoxide Warnings
STARTING AND OPERATING 347 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 350 348 STARTING AND OPERATING Opening The Door 2. Insert the fuel nozzle in the filler pipe and proceed with filling the fuel tank. For filling proceed as follows: 1. Open the door, by pushing and releasing on the indentation point indicated by the arrow. Filler Pipe 3.
Page 351 STARTING AND OPERATING 349 Emergency Refueling Procedure If the vehicle is out of fuel proceed as follows: 1. Open the liftgate and remove the emergency fuel fill funnel located in the cargo area. Emergency Fuel Fill Funnel — If Equipped With Full Size Spare Tire 2.
Page 352 350 STARTING AND OPERATING WARNING! • Do not to affix objects/plugs to the end of the filler neck other than is provided on the car. • The use of objects/plugs do not comply with the vehicle and may cause pressure increases inside the tank, creating dangerous conditions.
Page 353: Vehicle Loading
STARTING AND OPERATING 351 VEHICLE LOADING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Certification Label Payload As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label The payload of a vehicle is defined as the allowable load affixed to the driver’s side door or pillar.
Page 354 352 STARTING AND OPERATING Tire Size values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are The tire size on the Vehicle Certification Label represents added. the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Page 355: Driving On Slippery Surfaces
STARTING AND OPERATING 353 items down low and be sure that the weight is distributed DRIVING ON SLIPPERY SURFACES equally. Stow all loose items securely before driving. Acceleration Improper weight distributions can have an adverse effect Rapid acceleration on snow covered, wet, or other slip- on the way your vehicle steers and handles and the way pery surfaces may cause the driving wheels to pull the brakes operate.
Page 356: Traction
354 STARTING AND OPERATING Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a Driving through water more than a few inches/ wedge of water to build up between the tire and road centimeters deep will require extra caution to ensure surface.
Page 357: Shallow Standing Water
STARTING AND OPERATING 355 Shallow Standing Water CAUTION! Although your vehicle is capable of driving through • Always check the depth of the standing water shallow standing water, consider the following Cautions before driving through it. Never drive through and Warnings before doing so. standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
Page 358: Power Steering
356 STARTING AND OPERATING assist, you will still have the ability to steer the vehicle CAUTION! (Continued) manually. operate the vehicle if any fluid appears contami- nated, as this may result in further damage. Such WARNING! damage is not covered by the New Vehicle Limited Continued operation with reduced assist could pose Warranty.
Page 359: Trailer Towing
STARTING AND OPERATING 357 • If the condition persists, see your authorized dealer for If the “POWER STEERING SYSTEM HOT - PERFOR- MANCE MAY BE LIMITED” message and an icon are service. displayed on the EVIC screen, it indicates that extreme TRAILER TOWING steering maneuvers may have occurred, which caused an over temperature condition in the power steering system.
Page 360: Common Towing Definitions
358 STARTING AND OPERATING Common Towing Definitions The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight The following trailer towing related definitions will assist of the trailer must be supported by the scale. you in understanding the following information: Gross Combination Weight Rating (GCWR) Gross Vehicle Weight Rating (GVWR)
Page 361 STARTING AND OPERATING 359 Trailer Sway Control — Mechanical WARNING! The trailer sway control is a telescoping link that can be It is important that you do not exceed the maximum installed between the hitch receiver and the trailer tongue front or rear GAWR.
Page 362 360 STARTING AND OPERATING Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing Hitch age through spring (load) bars. They are typically used system may reduce handling, stability, braking for heavier loads to distribute trailer tongue weight to the performance, and could result in a collision.
Page 363: Trailer Hitch Classification
STARTING AND OPERATING 361 Trailer Hitch Classification tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can Trailer Hitch Classification Definitions Class Max.
Page 364: Trailer Towing Weights (Maximum Trailer Weight Ratings)
362 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. 1.4L Turbo Engine & 2.4 FWD Trailer towing is not recommended. Engine Max. GTW (Gross Trailer Wt.) Max.
Page 365: Trailer And Tongue Weight
STARTING AND OPERATING 363 Trailer And Tongue Weight Consider the following items when computing the weight on the rear axle of the vehicle: Never exceed the maximum tongue weight stamped on • The tongue weight of the trailer. your bumper or trailer hitch. •...
Page 366: Towing Requirements
364 STARTING AND OPERATING Towing Requirements WARNING! (Continued) To promote proper break-in of your new vehicle drive- • When hauling cargo, or towing a trailer, do not train components, the following guidelines are recom- overload your vehicle or trailer. Overloading can mended: cause a loss of control, poor performance, or dam- age to brakes, axle, engine, transmission, steering,...
Page 367 STARTING AND OPERATING 365 WARNING! (Continued) CAUTION! (Continued) • Total weight must be distributed between the tow • Then, during the first 500 miles (805 km) that a vehicle and the trailer such that the following four trailer is towed, do not drive over 50 mph (80 km/h) ratings are not exceeded: and do not make starts at full throttle.
Page 368 366 STARTING AND OPERATING • Check for signs of tire wear or visible tire damage • Trailer brakes are recommended for trailers over before towing a trailer. Refer to “Tires – General 1,000 lbs (453 kg) and required for trailers in excess of Information”...
Page 369 STARTING AND OPERATING 367 The electrical connections are all complete to the vehicle CAUTION! but you must mate the harness to a trailer connector. Refer to the following illustrations. If the trailer weighs more than 1,000 lbs (453 kg) loaded, it should have its own brakes and they should be of adequate capacity.
Page 370: Towing Tips
368 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic Transmission — If Equipped The DRIVE range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing.
Page 371 STARTING AND OPERATING 369 • Use speed control in flat terrain and with light loads to AutoStick maximize fuel efficiency. • When using the AutoStick shift control, select the highest gear that allows for adequate performance and Cooling System avoids frequent downshifts. For example, choose “5” if To reduce potential for engine and transmission over- the desired speed can be maintained.
Page 372: Recreational Towing (Behind Motorhome, Etc.)
370 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle ALL-WHEEL FRONT WHEEL DRIVE (FWD) DRIVE (AWD) MANUAL/ TOWING WHEELS OFF THE AUTOMATIC MANUAL AUTOMATIC CONDITION GROUND TRANSMISSION TRANSMISSION TRANSMISSION Flat Tow NONE NOT ALLOWED NOT ALLOWED NOT ALLOWED Dolly Tow...
Page 373 STARTING AND OPERATING 371 • Apply the Electric Park Brake (EPB). Place the trans- NOTE: You must ensure that the Auto Park Brake feature is disabled before towing this vehicle, to avoid inadver- mission in PARK. Turn the engine OFF. tent Electric Park Brake engagement.
Page 374 372 STARTING AND OPERATING CAUTION! CAUTION! • DO NOT flat tow this vehicle. Damage to the Towing this vehicle with ANY of its wheels on the drivetrain will result. If this vehicle requires tow- ground can cause severe transmission and/or power ing, make sure the drive wheels are OFF the transfer unit damage.
Page 375 IN CASE OF EMERGENCY CONTENTS ▫ Engine Compartment Fuses/Distribution HAZARD WARNING FLASHERS ...375 Unit .......398 BULB REPLACEMENT .
Page 376 374 IN CASE OF EMERGENCY TIRE SERVICE KIT STORAGE ....420 GEAR SELECTOR OVERRIDE ... . .433 ▫ Tire Service Kit — If Equipped ... .421 IGNITION KEY REMOVAL OVERRIDE .
Page 377: Hazard Warning Flashers
IN CASE OF EMERGENCY 375 HAZARD WARNING FLASHERS BULB REPLACEMENT The Hazard Warning flasher switch is located on the General Information switch bank below the radio. • Before you replace a bulb check the contacts to be sure Push the switch to turn on the Hazard Warning they are not oxidized.
Page 378: Replacement Bulbs
376 IN CASE OF EMERGENCY Replacement Bulbs Interior Bulbs Lamps Bulb Number Front Courtesy Light Front Courtesy Lights (Sun Visors) Rear Dome Light (Models Without Retractable roof) Rear Interior Lights (Models With Retractable roof) Interior Lights Dome Light (Glove Box)
Page 379 IN CASE OF EMERGENCY 377 Exterior Bulbs Lamps Bulb Number Low Beam/High Beam Headlamps HIR2 Front Position/Daytime Running Lights (DRL) P21/5 Front Direction Indicator Lamps PY21W Front Fog Lamps Side Indicators (Side View Mirror) WY5W Tail/Brake Lights/Turn Indicators P21W Center High Mounted Stop Lamp (CHMSL) LED (Serviced at an Authorized Dealer) Reverse P21W...
Page 380: Replacing Exterior Bulbs
378 IN CASE OF EMERGENCY Replacing Exterior Bulbs Hi/Lo Beam Light Halogen Headlamps To replace the bulbs proceed as follows: 1. Open the engine compartment and remove the head- lamp bulb cap. Front Lamps 1 — Headlamps 2 — Daytime Running Lamps Headlamp Bulb Cap 3 —...
Page 381 IN CASE OF EMERGENCY 379 2. Rotate the headlamp bulb socket counterclockwise then pull outwards. Headlamp Bulb Connector 4. Install the new headlamp bulb making sure it is properly locked. Headlamp Bulb Socket 3. Release the locking tab on the headlamp bulb connec- tor and remove the bulb and socket.
Page 382 380 IN CASE OF EMERGENCY 5. Install the headlamp bulb and socket; align the tabs WARNING! and turn it clockwise making sure it is properly locked. Carry out the operation of replacing lamps only with the engine off. Also make sure that the engine is cold, to avoid the danger of burns.
Page 383 IN CASE OF EMERGENCY 381 4. Rotate in a counterclockwise direction and remove the bulb and bulb socket. Position Light/Daytime Running Light/Fog light Access 1 — Screws Position Light/Daytime Running Light Assembly 2 — Access Door 1 — DRL Bulb Socket 3.
Page 384 382 IN CASE OF EMERGENCY 5. To replace the bulb gently push bulb and rotate 6. Insert the new bulb by pushing on it and turning it counterclockwise. clockwise. Make sure the bulb is correctly locked in place. 7. Install the bulb and sockets and rotate them clockwise, making sure that it is properly locked.
Page 385 IN CASE OF EMERGENCY 383 Position Light/Daytime Running Light/Fog Light Access Fog Light Assembly 4. Rotate the bulb counterclockwise, and then replace the 1 — Screws bulb. 2 — Access Door 5. Insert the new bulb in the socket, making sure the bulb 3.
Page 386 384 IN CASE OF EMERGENCY Side Indicators on External Rear View Mirrors – (If Equipped) CAUTION! The procedure is described as a guideline. For the replacement of the lamp it is recommended that you contact your authorized dealer. To replace the bulb proceed as follows: 1.
Page 387 IN CASE OF EMERGENCY 385 3. Remove the bulb socket and bulb from the transparent To replace the bulbs proceed as follows: lens assembly by rotating the socket counterclockwise. 1. Open the liftgate. 4. Remove the bulb from the bulb socket by pulling the 2.
Page 388 386 IN CASE OF EMERGENCY 3. Remove the rear tail lamp, sliding it toward the 4. Remove the screws and remove the rear tail lamp outside as shown. holder. Tail Lamp Removal Rear Lamp Assembly 1 — Screws...
Page 389 IN CASE OF EMERGENCY 387 5. Replace the bulb as necessary. 6. Insert the new bulb, making sure it is properly locked. 7. Reassemble the lamp assembly on the rear tail lamp housing, tightening the screws. 8. Reposition the rear tail lamp on the vehicle. 9.
Page 390 388 IN CASE OF EMERGENCY License Plate Lights To replace the bulbs proceed as follows: 1. Using a suitable tool remove the license plate lens. License Plate Light License Plate Light Location...
Page 391: Replacing Interior Bulbs
IN CASE OF EMERGENCY 389 2. Remove the bulbs from the individual side contacts. Replacing Interior Bulbs Front Courtesy Light 3. Insert the new bulbs, and ensure that they are properly locked between the contacts. To replace the bulbs proceed as follows: 4.
Page 392 390 IN CASE OF EMERGENCY 2. Release the retainer clips and bulb housing as shown. 3. Replace the bulbs by pulling straight out of bulb housing. Front Courtesy Bulb Housing Front Courtesy Bulb Housing 1 — Retaining Clips 2 — Bulb Housing...
Page 393 IN CASE OF EMERGENCY 391 4. Insert the new bulbs, making sure that they are properly locked. 5. Reassemble the bulb housing and courtesy light hous- ing making sure that they are properly locked. 6. Install the front courtesy light making sure that it is properly locked.
Page 394 392 IN CASE OF EMERGENCY Dome Light Glove Compartment 3. Insert the new bulb, making sure it is properly locked. To replace the bulb proceed as follows: Rear Dome Light — Without Retractable Roof To replace the bulbs proceed as follows: 1.
Page 395 IN CASE OF EMERGENCY 393 Dome Light To replace the bulbs proceed as follows: 1. Lower the handle in the direction shown remove the dome light. Rear Dome Light 3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Retractable Roof Light...
Page 396 394 IN CASE OF EMERGENCY 2. Replace the bulb by removing it from the side contacts. Interior Cargo Lights To replace the bulbs proceed as follows: 1. Open the luggage compartment and remove the dome light assembly. 2. Open the light cover and replace the bulb. Bulb 3.
Page 397 IN CASE OF EMERGENCY 395 3. Close the light cover over the bulb. WARNING! (Continued) 4. Reinstall the dome light in its correct position. • Halogen lamps must be handled by touching only the metallic part. If the transparent bulb is in WARNING! contact with the fingers, reduces the intensity of the emitted light and you can also affect the life of...
Page 398: Fuses
396 IN CASE OF EMERGENCY FUSES WARNING! (Continued) • If a general protection fuse for safety systems (air WARNING! bag system, braking system), power unit systems • When replacing a blown fuse, always use an ap- (engine system, gearbox system) or steering system propriate replacement fuse with the same amp blows, contact an authorized dealer.
Page 399 IN CASE OF EMERGENCY 397 Also please be aware that when using power outlets for Fuse Removal extended periods of time with the engine off may result To replace a fuse use the extractor attached to the fuse in vehicle battery discharge. cover (located on the inside of the engine compartment fuse cover.
Page 400: Access To The Fuses
398 IN CASE OF EMERGENCY Access To The Fuses Engine Compartment Fuses/Distribution Unit The fuses are grouped into four controllers located in the The engine compartment fuse panel is located on the left engine compartment, under the instrument panel and on side of the engine compartment.
Page 401 IN CASE OF EMERGENCY 399 Removing Fuse Cover and Locking Screw Proceed as follows: 1. Slowly turn the screw counterclockwise. 2. Slowly release the screw. 3. Remove the fuse cover by sliding it upward. Fuse Panel And Cover Location 1 — Mounting Screw 2 —...
Page 402 400 IN CASE OF EMERGENCY Mounting Fuse Cover and Locking Screw Proceed as follows: 1. Properly secure the fuse cover to the box, slide com- pletely from top to bottom. 2. Fully depress the screw, using the special screwdriver supplied. 3.
Page 403 IN CASE OF EMERGENCY 401 Cavity Maxi Fuse Cartage Fuse Mini Fuse Description 70 Amp Tan – – Module Body Computer 60 Amp Blue – – Module Body Computer, Rear Distribution Units – 20 Amp Blue – Controller Power Supply Body Computer –...
Page 404 402 IN CASE OF EMERGENCY Cavity Maxi Fuse Cartage Fuse Mini Fuse Description – – 5 Amp Tan Pump Power After run 40 Amp Orange – – Brake Control Module Pump – – 5 Amp Tan Engine Control Module Power, Automatic Transmission –...
Page 405 IN CASE OF EMERGENCY 403 Cavity Maxi Fuse Cartage Fuse Mini Fuse Description – – 15 Amp Blue Electronic Unit Supply Auto- matic Transmission – – 30 Amp Green Heated Windshield – If Equipped – 40 Amp Green – Air Conditioning Fan –...
Page 406: Body Computer Fuse Center
404 IN CASE OF EMERGENCY Body Computer Fuse Center The controller is located at the left side of the steering column at the bottom of the instrument panel. For the fuse replacement see your authorized dealer.
Page 407 IN CASE OF EMERGENCY 405 Body Controller Fuse Cavities...
Page 408 406 IN CASE OF EMERGENCY Cavity Mini Fuse Description 7.5 Amp Brown Fan Air Conditioning, Power Socket 20 Amp Yellow Power Window Front (Passenger Side) 20 Amp Yellow Power Window Front (Drivers Side) 15 Amp Blue Supply Uconnect System, Air Conditioning, USB Port, Rear lateral ceiling light in case of open roof, EOBD port 10 Amp Red System Power Forward Collision Warning Plus, All Wheel Drive (AWD), IPC,...
Page 409: Rear Cargo Fuse/Relay Distribution Unit
IN CASE OF EMERGENCY 407 7.5 Amp Brown Air Conditioning Compressor, Plaque Automatic Transmission, Rear Camera, Air Conditioning, LDW - Lane Departure Warning, ASS - Auxiliary Stack Switch, DSU - Drive Syle Selector Unit, Reverse gear switch, side mirrors and rear window defrost 7.5 Amp Brown Supply IPC/Starter Device/System Keyless Enter-N-Go, Brake Pedal Switch...
Page 410 408 IN CASE OF EMERGENCY Push on the left side of the access door to unhinge and remove. Rear Cargo Fuse Cavities Cavity Mini Fuse Description 20 Amp Yellow Audio System 20 Amp Yellow Electric Sunroof 30 Amp Green Power Seat (driver side) 7.5 Amp Brown Power Seat (driver side) Lumbar Adjustment 20 Amp Yellow...
Page 411: Jacking And Tire Changing
IN CASE OF EMERGENCY 409 JACKING AND TIRE CHANGING WARNING! (Continued) • The jack is designed to be used as a tool for WARNING! changing tires only. The jack should not be used to • Do not attempt to change a tire on the side of the lift the vehicle for service purposes.
Page 412: Jack Location/Spare Tire Stowage - If Equipped
410 IN CASE OF EMERGENCY Jack Location/Spare Tire Stowage — If Equipped 1. Open the liftgate. The jack and tools are located in the rear storage com- 2. Lift the access cover using the load floor handle. partment if equipped, inside a special container. Load Floor Handle Jack And Tools Location...
Page 413 IN CASE OF EMERGENCY 411 3. Remove the fastener securing the spare tire. Jack And Tools 1 — Wheel Bolt Wrench Spare Tire Fastener 2 — Jack 3 — Emergency Funnel 4. Remove the jack, wheel bolt wrench, and wheel 4 —...
Page 414: Preparations For Jacking
412 IN CASE OF EMERGENCY 2. Turn on the Hazard Warning flasher. WARNING! 3. Set the Electric Park Brake. A loose tire or jack thrown forward in a collision or 4. Place the gear selector into PARK (automatic transmis- hard stop could endanger the occupants of the ve- sion) or REVERSE (manual transmission).
Page 415: Jacking Instructions
IN CASE OF EMERGENCY 413 Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. • Do not get under the vehicle when it is on a jack. If Carefully follow these tire changing warnings to help prevent personal injury or damage to your you need to get under a raised vehicle, take it to a vehicle:...
Page 416 414 IN CASE OF EMERGENCY 3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counterclock- wise one turn while the wheel is still on the ground. Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on...
Page 417 IN CASE OF EMERGENCY 415 4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle inside the cutout in the sill cladding.
Page 418 416 IN CASE OF EMERGENCY Front Jacking Engagement Point Rear Jacking Location...
Page 419 IN CASE OF EMERGENCY 417 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7.
Page 420 418 IN CASE OF EMERGENCY NOTE: • Your vehicle may be equipped with a compact spare tire or a limited — use spare tire. For further infor- mation refer to “Tires — General Information” in “Maintaining And Caring For Your Vehicle”. •...
Page 421: Road Tire Installation
IN CASE OF EMERGENCY 419 9. Lower the vehicle to the ground by turning the wheel Road Tire Installation bolt wrench counterclockwise. 1. Mount the road tire on the axle. 10. Finish tightening the wheel bolts. Push down on the 2.
Page 422: Tire Service Kit Storage
420 IN CASE OF EMERGENCY 4. Finish tightening the wheel bolts. Push down on the TIRE SERVICE KIT STORAGE wrench while at the end of the handle for increased The Tire Service Kit is located in the rear storage com- leverage.
Page 423: Tire Service Kit - If Equipped
IN CASE OF EMERGENCY 421 Tire Service Kit — If Equipped If a tire is punctured, you can make a first emergency repair using the Tire Service Kit located in the rear storage compartment inside the storage container. Remove the Tire Service Kit from the vehicle, take it out from the bag and place it near the punctured tire.
Page 424 422 IN CASE OF EMERGENCY WARNING! (Continued) WARNING! (Continued) – If the tire has any damage from driving with Kit to come in contact with hair, eyes, or clothing. extremely low tire pressure. Tire Service Kit sealant is harmful if inhaled, –...
Page 425 IN CASE OF EMERGENCY 423 Push the Tire Service Kit power button to the “I” position. WARNING! The electric compressor will be turned on, sealant and air will inflate the tire. Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after Minimum 26 psi (1.8 bar) of pressure should be reached using Tire Service Kit.
Page 426 424 IN CASE OF EMERGENCY WARNING! The metal end fitting from Power Plug may get hot after use, so it should be handled carefully. NOTE: Replace the sealant canister prior to the expira- tion date at your authorized dealer. Tire Service Kit Expiration Date Location WARNING! Store the sealant canister in its special compartment, away from sources of heat.
Page 427: Jump Starting
IN CASE OF EMERGENCY 425 JUMP STARTING WARNING! If your vehicle has a discharged battery it can be jump- Do not attempt jump starting if the battery is frozen. started using a set of jumper cables and a battery in It could rupture or explode and cause personal injury.
Page 428 426 IN CASE OF EMERGENCY NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised.
Page 429: Jump Starting Procedure
IN CASE OF EMERGENCY 427 Proceed as follows: Jump Starting Procedure 1. Set the Electric Park Brake, shift the automatic trans- WARNING! mission into PARK (manual transmission in NEU- TRAL) and turn the ignition to STOP/OFF. Failure to follow this jump-starting procedure could result in personal injury or property damage due to 2.
Page 430 428 IN CASE OF EMERGENCY 3. Connect the negative (-) end of the jumper cable to the 5. Start the engine in the vehicle that has the booster negative (-) post of the booster battery. battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged 4.
Page 431: Enhanced Accident Response System
IN CASE OF EMERGENCY 429 4. Disconnect the opposite end of the positive (+) jumper Enhanced Accident Response System cable from the positive (+) post of the vehicle with the In the event of an impact, if the communication network discharged battery.
Page 432: Enhanced Accident Response System Reset Procedure
430 IN CASE OF EMERGENCY • Turn off the Fuel Pump Heater. move your vehicle to the side of the road, you must follow the system reset procedure. • Turn off the HVAC Blower Motor. • Close the HVAC Circulation Door. Customer Action Customer Will See 1.
Page 433: Refueling In Emergency
IN CASE OF EMERGENCY 431 If a reset procedure step is not completed within 60 Customer Action Customer Will See seconds, then the turn signal lights will blink and the 5. Turn Right Turn Signal Right Turn Light Is ON reset procedure must be performed again in order to be Switch ON.
Page 434 432 IN CASE OF EMERGENCY • In city traffic — while stopped, put transmission in • You can also turn the temperature control to maximum NEUTRAL, but do not increase engine idle speed. heat, the mode control to floor and the blower control to high.
Page 435: Gear Selector Override
IN CASE OF EMERGENCY 433 GEAR SELECTOR OVERRIDE If a malfunction occurs and the gear selector cannot be moved out of the PARK position, you can use the following procedure to temporarily move the gear selec- tor: 1. Turn the engine OFF. 2.
Page 436 434 IN CASE OF EMERGENCY Removing Gear Selector Bezel Gear Selector Override Location 4. Push and maintain firm pressure on the brake pedal. 6. Move the gear selector to the NEUTRAL position. 5. Insert a small screwdriver or similar tool down into 7.
Page 437: Ignition Key Removal Override
IN CASE OF EMERGENCY 435 IGNITION KEY REMOVAL OVERRIDE This vehicle is equipped with a Key Ignition Park Inter- lock which requires the transmission to be in PARK before the ignition switch can be turned to the STOP/ OFF (key removal) position. To remove the key manually, proceed as follows: 1.
Page 438 436 IN CASE OF EMERGENCY Lower Steering Column Cover Release Tab Location 1 — Trim Screws 5. With one hand, pull down on the release tab and with the other, pull out the ignition key.
Page 439: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 437 FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels.
Page 440 438 IN CASE OF EMERGENCY Whenever the transmission remains in NEUTRAL for CAUTION! (Continued) more than two seconds, you must press the brake pedal reduce the risk of clutch or transmission failure to engage DRIVE or REVERSE. during prolonged efforts to free a stuck vehicle. NOTE: Push the ESC Off switch (if necessary), to place •...
Page 441: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 439 TOWING A DISABLED VEHICLE WARNING! (Continued) This section describes procedures for towing a disabled even failure, of the axle and tires. A tire could vehicle using a commercial towing service. explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping when you are stuck and do not let anyone near...
Page 442 440 IN CASE OF EMERGENCY Proper towing or lifting equipment is required to prevent If you must use the accessories (wipers, defrosters, etc.) damage to your vehicle. Use only tow bars and other while being towed, the ignition must be in the MAR/ equipment designed for this purpose, following equip- RUN position.
Page 443: Front Wheel Drive (Fwd) Models
IN CASE OF EMERGENCY 441 NOTE: Ensure that the Electric Park Brake is released, CAUTION! and remains released, while being towed. • Do not use sling type equipment when towing. CAUTION! Vehicle damage may occur. • When securing the vehicle to a flat bed truck, do Towing this vehicle in violation of the above require- not attach to front or rear suspension components.
Page 444: Tow Eye Usage - If Equipped
442 IN CASE OF EMERGENCY When using a tow eye be sure to follow the “Tow Eye CAUTION! Usage Precautions” and the “Towing A Disabled Vehicle” • DO NOT tow this vehicle with ANY of its wheels instructions in this section. on the ground.
Page 445 IN CASE OF EMERGENCY 443 Tow Eye Usage Precautions WARNING! NOTE: Stand clear of vehicles when pulling with tow eyes. • Ensure that the tow eye is properly seated and secure • Do not use a chain with a tow eye. Chains may in the mounting receptacle.
Page 446 444 IN CASE OF EMERGENCY CAUTION! • The tow eye must be used exclusively for roadside assistance operations. Only use the tow eye with an appropriate device in accordance with the highway code (a rigid bar or rope) to flat tow the vehicle for a short distance to the nearest service location.
Page 447: Front Tow Eye Installation
IN CASE OF EMERGENCY 445 Front Tow Eye Installation The front tow eye receptacle is located behind a access door, located on the right front bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle.
Page 448: Rear Tow Eye Installation
446 IN CASE OF EMERGENCY Rear Tow Eye Installation The rear tow eye receptacle is located behind a access door on the rear bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle.
Page 449 MAINTAINING AND CARING FOR YOUR VEHICLE CONTENTS ▫ Engine Oil ......464 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS .
Page 450 448 MAINTAINING AND CARING FOR YOUR VEHICLE ▫ Brake System ......482 ▫ Tire Inflation Pressures ....509 ▫...
Page 451: Emissions Inspection And Maintenance Programs
MAINTAINING AND CARING FOR YOUR VEHICLE 449 EMISSIONS INSPECTION AND MAINTENANCE Your vehicle has a simple ignition actuated test, which PROGRAMS you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the In some localities, it may be a legal requirement to pass following: an inspection of your vehicle’s emissions control system.
Page 452: Replacement Parts
450 MAINTAINING AND CARING FOR YOUR VEHICLE the ignition or start the engine. This means that your before going to the I/M station. The I/M station can fail vehicle’s OBD II system is not ready and you should your vehicle because the MIL is on with the engine not proceed to the I/M station.
Page 453: Maintenance Schedule
MAINTAINING AND CARING FOR YOUR VEHICLE 451 NOTE: Intentional tampering with emissions control Based on engine operation conditions, the oil change systems may void your warranty and could result in civil indicator message will illuminate in the instrument clus- penalties being assessed against you. ter.
Page 454 452 MAINTAINING AND CARING FOR YOUR VEHICLE • Check the fluid levels of the coolant reservoir, and NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or brake master cylinder reservoir, and fill as needed. 350 hours of engine run time, whichever comes first.
Page 455: Maintenance Chart
MAINTAINING AND CARING FOR YOUR VEHICLE 453 Refer to the “Maintenance Chart” on the following page for the required maintenance intervals. Maintenance Chart Mileage or time passed (whichever comes first) Years Or Kilometers Check tire condition/wear and adjust pressure, if necessary, •...
Page 456 454 MAINTAINING AND CARING FOR YOUR VEHICLE Mileage or time passed (whichever comes first) Years Or Kilometers Check operation of lighting system (headlamps, direction indicators, hazard warning lights, luggage compartment, • • • • • • • • • • •...
Page 457 MAINTAINING AND CARING FOR YOUR VEHICLE 455 Mileage or time passed (whichever comes first) Years Or Kilometers Check engine control system • • • • • • • • • • • • • • • operation (via diagnostic tool). Visually inspect condition of: exterior bodywork, underbody protection, pipes and hoses...
Page 458 456 MAINTAINING AND CARING FOR YOUR VEHICLE Mileage or time passed (whichever comes first) Years Or Kilometers Check operation of windshield • • • • • • • • washer system and adjust jets if necessary. Check cleanliness of hood and tailgate locks and cleanli- •...
Page 459 MAINTAINING AND CARING FOR YOUR VEHICLE 457 Mileage or time passed (whichever comes first) Years Or Kilometers Visual inspect the condition of • • • the accessory drive belt. Check the tension of the ac- • • • • • •...
Page 460 458 MAINTAINING AND CARING FOR YOUR VEHICLE Mileage or time passed (whichever comes first) Years Or Kilometers Inspect the rear differential • • • fluid level. Replace spark plugs (1.4L • • • • • Turbo engine). (**) Replace spark plugs (2.4L en- •...
Page 461 MAINTAINING AND CARING FOR YOUR VEHICLE 459 Mileage or time passed (whichever comes first) Years Or Kilometers Change the manual transmis- sion fluid if using your vehicle for any of the following: trailer towing, heavy loading, taxi, police, delivery service (com- •...
Page 462 460 MAINTAINING AND CARING FOR YOUR VEHICLE Mileage or time passed (whichever comes first) Years Or Kilometers Replace the timing belt (1.4L • Turbo Engine). Recommend replacement (**) The spark plug change is distance based only, yearly intervals do not apply. The following are essential to •...
Page 463 MAINTAINING AND CARING FOR YOUR VEHICLE 461 • Strictly comply with the spark plug replacement inter- WARNING! val given in the “Maintenance Schedule” for spark • You can be badly injured working on or around a plug replacement. motor vehicle. Do only service work for which you •...
Page 464: Engine Compartment - 1.4L Turbo Engine
462 MAINTAINING AND CARING FOR YOUR VEHICLE ENGINE COMPARTMENT — 1.4L TURBO ENGINE 1 — Air Cleaner Filter 4 — Battery 7 — Coolant Pressure Cap 2 — Engine Oil Dipstick 5 — Power Distribution Center (Fuses) 8 — Coolant Pressure Bottle 3 —...
Page 465: Engine Compartment - 2.4L Engine
MAINTAINING AND CARING FOR YOUR VEHICLE 463 ENGINE COMPARTMENT — 2.4L ENGINE 1 — Engine Air Cleaner Filter 4 — Brake Fluid Reservoir 7 — Washer Fluid Reservoir 2 — Engine Oil Dipstick 5 — Battery 8 — Coolant Pressure Cap 3 —...
Page 466: Maintenance Procedures
464 MAINTAINING AND CARING FOR YOUR VEHICLE MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance • Your vehicle has been built with improved fluids services determined by the engineers who designed your that protect the performance and durability of your vehicle.
Page 467 MAINTAINING AND CARING FOR YOUR VEHICLE 465 after a fully warmed engine is shut off. Do not check oil CAUTION! (Continued) level before starting the engine after it has sat overnight. temperature. This loss of oil pressure and increased Checking engine oil level when the engine is cold will oil temperature could damage your engine.
Page 468 466 MAINTAINING AND CARING FOR YOUR VEHICLE Engine Oil Selection — 1.4L Turbo Engine low temperature starting and vehicle fuel economy. Your engine oil filler cap also states the recommended engine For best performance and maximum protection for tur- oil viscosity grade for your engine. bocharged engines under all types of operating condi- tions, the manufacturer recommends synthetic engine Lubricants which do not have both the engine oil certi-...
Page 469: Engine Oil Filter
MAINTAINING AND CARING FOR YOUR VEHICLE 467 Materials Added To Engine Oil Engine Oil Filter Selection The manufacturer strongly recommends against the ad- This manufacturer’s engines have a full-flow type dispos- dition of any additives (other than leak detection dyes) to able oil filter.
Page 470: Maintenance-Free Battery
468 MAINTAINING AND CARING FOR YOUR VEHICLE Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. cleaner, hoses, etc.) unless such removal is necessary You will never have to add water, nor is periodic main- for repair or maintenance. Make sure that no one is tenance required.
Page 471: Air Conditioner Maintenance
MAINTAINING AND CARING FOR YOUR VEHICLE 469 WARNING! (Continued) CAUTION! (Continued) an output greater than 12 Volts. Do not allow cable battery case. Cable clamps should be tight on the clamps to touch each other. terminal posts and free of corrosion. •...
Page 472 470 MAINTAINING AND CARING FOR YOUR VEHICLE WARNING! CAUTION! • Use only refrigerants and compressor lubricants Do not use chemical flushes in your air conditioning approved by the manufacturer for your air condi- system as the chemicals can damage your air condi- tioning system.
Page 473: Body Lubrication
MAINTAINING AND CARING FOR YOUR VEHICLE 471 Body Lubrication Wiper Blades Locks and all body pivot points, including such items as Clean the rubber edges of the wiper blades and the seat tracks, door hinge pivot points and rollers, liftgate, windshield and rear window periodically with a sponge tailgate, decklid, sliding doors and hood hinges, should or soft cloth and a mild nonabrasive cleaner.
Page 474 472 MAINTAINING AND CARING FOR YOUR VEHICLE NOTE: Life expectancy of wiper blades varies depending At every valid activation of Service Position command, on geographical area and frequency of use. Poor perfor- the wiper blades are activated for 250 ms. mance of blades may be present with chattering, marks, The Service Position command can be repeated several water lines or wet spots.
Page 475 MAINTAINING AND CARING FOR YOUR VEHICLE 473 Front Wiper Blade Removal/Installation 1. Lift the front wiper arm upward to raise the wiper blade off of the windshield. 2. Push the release button on the arm of the wiper blade. 3. Push the wiper blade up the and remove it. 1 —...
Page 476: Adding Washer Fluid
474 MAINTAINING AND CARING FOR YOUR VEHICLE Rear Wiper Blade Removal/Installation Refer to “Engine Compartment” in this section for fur- ther information. 1. Carefully lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. WARNING! 2.
Page 477 MAINTAINING AND CARING FOR YOUR VEHICLE 475 have an authorized technician inspect the complete ex- WARNING! (Continued) haust system and adjacent body areas for broken, dam- be grass or leaves coming into contact with your aged, deteriorated, or mispositioned parts. Open seams exhaust system.
Page 478 476 MAINTAINING AND CARING FOR YOUR VEHICLE the vehicle, turn off the engine and allow it to cool. CAUTION! (Continued) Service, including a tune-up to manufacturer’s specifica- performance, have your vehicle serviced promptly. tions, should be obtained immediately. Continued operation of your vehicle with a severe To minimize the possibility of catalytic converter dam- malfunction could cause the converter to overheat, age:...
Page 479: Cooling System
MAINTAINING AND CARING FOR YOUR VEHICLE 477 Cooling System applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, WARNING! flushed and refilled with fresh engine coolant (anti- freeze). Check the front of the A/C condenser for any •...
Page 480 478 MAINTAINING AND CARING FOR YOUR VEHICLE Refer to the “Maintenance Schedule” for the proper CAUTION! (Continued) maintenance intervals. coolant (antifreeze) is introduced into the cooling Selection Of Coolant system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh Refer to “Fluids, Lubricants, And Genuine Parts”...
Page 481: Maintaining And Caring For Your Vehicle
MAINTAINING AND CARING FOR YOUR VEHICLE 479 • Mix a minimum solution of 50% OAT engine coolant Adding Coolant that meets the requirements of FCA Material Standard Your vehicle has been built with an improved engine MS.90032 and distilled water. Use higher concentra- coolant (OAT coolant conforming to MS.90032) that al- tions (not to exceed 70%) if temperatures below −34°F lows extended maintenance intervals.
Page 482 480 MAINTAINING AND CARING FOR YOUR VEHICLE • Some vehicles require special tools to add coolant The cap should be inspected and cleaned if there is any properly. Failure to fill these systems properly could accumulation of foreign material on the sealing surfaces. lead to severe internal engine damage.
Page 483 MAINTAINING AND CARING FOR YOUR VEHICLE 481 Disposal Of Used Engine Coolant As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a Used ethylene glycol-based engine coolant (antifreeze) is month. a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal When additional engine coolant (antifreeze) is needed to rules for your community.
Page 484: Brake System
482 MAINTAINING AND CARING FOR YOUR VEHICLE • Do not overfill the coolant expansion bottle. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install • Check the coolant freeze point in the radiator and in ONLY the correct type thermostat.
Page 485 MAINTAINING AND CARING FOR YOUR VEHICLE 483 when the pads are replaced. However, low fluid level WARNING! may be caused by a leak and a checkup may be needed. Riding the brakes can lead to brake failure and NOTE: If your vehicle is equipped with a manual possibly a collision.
Page 486 484 MAINTAINING AND CARING FOR YOUR VEHICLE WARNING! WARNING! (Continued) cause it to boil unexpectedly during hard or pro- • Use only manufacturer’s recommended brake longed braking, resulting in sudden brake failure. fluid. Refer to “Fluids, Lubricants, And Genuine This could result in a collision. Parts”...
Page 487: Manual Transmission - If Equipped
MAINTAINING AND CARING FOR YOUR VEHICLE 485 Fluid Level Check CAUTION! Check the fluid level by removing the fill plug. The fluid Use of improper brake fluids will affect overall level should be between the bottom of the fill hole and a clutch system performance.
Page 488: Automatic Transmission - If Equipped
486 MAINTAINING AND CARING FOR YOUR VEHICLE Automatic Transmission — If Equipped CAUTION! Selection Of Lubricant Using a transmission fluid other than the manufac- It is important to use the proper transmission fluid to turer’s recommended fluid may cause deterioration ensure optimum transmission performance and life.
Page 489 MAINTAINING AND CARING FOR YOUR VEHICLE 487 CAUTION! CAUTION! Do not use chemical flushes in your transmission as If a transmission fluid leak occurs, visit your autho- the chemicals can damage your transmission compo- rized dealer immediately. Severe transmission dam- nents.
Page 490: Appearance Care And Protection From Corrosion
488 MAINTAINING AND CARING FOR YOUR VEHICLE Appearance Care And Protection From Corrosion What Causes Corrosion? Corrosion is the result of deterioration or removal of Protection Of Body And Paint From Corrosion paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 491 MAINTAINING AND CARING FOR YOUR VEHICLE 489 • If insects, tar, or other similar deposits have accumu- CAUTION! (Continued) lated on your vehicle, use MOPAR Super Kleen Bug • Use of power washers exceeding 1,200 psi (8 274 and Tar Remover to remove. kPa) can result in damage or removal of paint and •...
Page 492 490 MAINTAINING AND CARING FOR YOUR VEHICLE • If your vehicle is damaged due to a collision or similar Wheel And Wheel Trim Care cause that destroys the paint and protective coating, • All wheels and wheel trim, especially aluminum and have your vehicle repaired as soon as possible.
Page 493 MAINTAINING AND CARING FOR YOUR VEHICLE 491 • For tough stains, apply MOPAR Total Clean, or a mild CAUTION! soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. Do not use scouring pads, steel wool, a bristle brush, or metal polishes.
Page 494 492 MAINTAINING AND CARING FOR YOUR VEHICLE Your leather upholstery can be best preserved by regular CAUTION! cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery Direct contact of air fresheners, insect repellents, and should be removed promptly with a damp cloth.
Page 495 MAINTAINING AND CARING FOR YOUR VEHICLE 493 Cleaning Headlights Glass Surfaces Your vehicle has plastic headlights that are lighter and All glass surfaces should be cleaned on a regular basis less susceptible to stone breakage than glass headlights. with MOPAR Glass Cleaner, or any commercial household-type glass cleaner.
Page 496 494 MAINTAINING AND CARING FOR YOUR VEHICLE Instrument Panel Bezels 2. Dry with a soft cloth. Seat Belt Maintenance CAUTION! Do not bleach, dye or clean the belts with chemical When installing hanging air fresheners in your ve- solvents or abrasive cleaners. This will weaken the fabric. hicle, read the installation instructions carefully.
Page 497: Raising The Vehicle
MAINTAINING AND CARING FOR YOUR VEHICLE 495 RAISING THE VEHICLE WARNING! In the case where it is necessary to raise the vehicle, go to A frayed or torn belt could rip apart in a collision and a your authorized dealer or service station. leave you with no protection.
Page 498 496 MAINTAINING AND CARING FOR YOUR VEHICLE Lifting Point Locations...
Page 499: Tire Safety Information
MAINTAINING AND CARING FOR YOUR VEHICLE 497 TIRE SAFETY INFORMATION NOTE: • P (Passenger) — Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion.
Page 500 498 MAINTAINING AND CARING FOR YOUR VEHICLE • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure com- standards and it begins with the tire diameter molded pact spare tires have the letter “T”...
Page 501 MAINTAINING AND CARING FOR YOUR VEHICLE 499 EXAMPLE: R = Construction code – R means radial construction, or – D means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index –...
Page 502: Tire Identification Number (Tin)
500 MAINTAINING AND CARING FOR YOUR VEHICLE EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or •...
Page 503 MAINTAINING AND CARING FOR YOUR VEHICLE 501 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 504: Tire Terminology And Definitions
502 MAINTAINING AND CARING FOR YOUR VEHICLE Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after Cold Tire Inflation Pressure the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three...
Page 505: Tire Loading And Tire Pressure
MAINTAINING AND CARING FOR YOUR VEHICLE 503 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (Door)
Page 506 504 MAINTAINING AND CARING FOR YOUR VEHICLE Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2.
Page 507 MAINTAINING AND CARING FOR YOUR VEHICLE 505 3. Tire size designed for your vehicle. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 4. Cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires.
Page 508 506 MAINTAINING AND CARING FOR YOUR VEHICLE 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 509 MAINTAINING AND CARING FOR YOUR VEHICLE 507...
Page 510: Tires - General Information
508 MAINTAINING AND CARING FOR YOUR VEHICLE Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading • Improperly inflated tires are dangerous and can can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the cause collisions.
Page 511: Tire Inflation Pressures
MAINTAINING AND CARING FOR YOUR VEHICLE 509 Tread Wear WARNING! (Continued) Improper cold tire inflation pressures can cause abnor- • Always drive with each tire inflated to the recom- mal wear patterns and reduced tread life, resulting in the mended cold tire inflation pressure. need for earlier tire replacement.
Page 512 510 MAINTAINING AND CARING FOR YOUR VEHICLE • Inspect tires for signs of tire wear or visible damage. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per After inspecting or adjusting the tire pressure, al- 12°F (7°C) of air temperature change.
Page 513: Tire Pressures For High Speed Operation
MAINTAINING AND CARING FOR YOUR VEHICLE 511 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 514: Tire Types
512 MAINTAINING AND CARING FOR YOUR VEHICLE Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
Page 515 MAINTAINING AND CARING FOR YOUR VEHICLE 513 Snow tires generally have lower speed ratings than what WARNING! was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph Do not use Summer tires in snow/ice conditions. You (120 km/h).
Page 516: Run Flat Tires - If Equipped
514 MAINTAINING AND CARING FOR YOUR VEHICLE Run Flat Tires — If Equipped Spare Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles NOTE: For vehicles equipped with Tire Service Kit (80 km) at 50 mph (80 km/h) after a rapid loss of inflation instead of a spare tire, please refer to “Tire Service Kit”...
Page 517: Tread Wear Indicators
MAINTAINING AND CARING FOR YOUR VEHICLE 515 Refer to “Freeing A Stuck Vehicle” in “In Case Of Tread Wear Indicators Emergency” for further information. Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. WARNING! Fast spinning tires can be dangerous.
Page 518: Life Of Tire
516 MAINTAINING AND CARING FOR YOUR VEHICLE • Performance tires, tires with a speed rating of V or These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth higher, and Summer tires typically have a reduced becomes a 1/16 of an inch (1.6 mm).
Page 519: Replacement Tires
MAINTAINING AND CARING FOR YOUR VEHICLE 517 Replacement Tires affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match The tires on your new vehicle provide a balance of many those of the original wheels. characteristics.
Page 520: Tire Chains (Traction Devices)
518 MAINTAINING AND CARING FOR YOUR VEHICLE WARNING! (Continued) CAUTION! braking of your vehicle. This can cause unpredict- Replacing original tires with tires of a different size able handling and stress to steering and suspen- may result in false speedometer and odometer read- sion components.
Page 521 MAINTAINING AND CARING FOR YOUR VEHICLE 519 WARNING! CAUTION! (Continued) • Install device as tightly as possible and then re- Using tires of different size and type (M+S, Snow) tighten after driving about ½ mile (0.8 km). between front and rear axles can cause unpredictable •...
Page 522: Tire Rotation Recommendations
520 MAINTAINING AND CARING FOR YOUR VEHICLE TIRE ROTATION RECOMMENDATIONS The suggested Front Wheel Drive (FWD) rotation method is the “forward cross” shown in the following The tires on the front and rear of your vehicle operate at diagram. This rotation pattern does not apply to some different loads and perform different steering, handling, directional tires that must not be reversed.
Page 523: Storing The Vehicle
MAINTAINING AND CARING FOR YOUR VEHICLE 521 The suggested Four Wheel Drive (4WD) Tire rotation CAUTION! method is the “rearward cross” shown in the following diagram. Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel.
Page 524 522 MAINTAINING AND CARING FOR YOUR VEHICLE • If you do not disconnect the battery from the electrical • Do not drain the engine cooling system. system, check the battery charge every thirty days. • Whenever you leave the vehicle is stationary for two •...
Page 525 MAINTAINING AND CARING FOR YOUR VEHICLE 523 CAUTION! Before removal of the positive and negative termi- nals to the battery, wait at least a minute with ignition switch in the OFF position and close the drivers door. When reconnecting the positive and negative terminals to the battery be sure the ignition switch is in the OFF position and the drivers door is closed.
Page 527 TECHNICAL DATA CONTENTS VEHICLE IDENTIFICATION NUMBER ..526 FLUIDS, LUBRICANTS, AND GENUINE PARTS ......530 WHEEL AND TIRE TORQUE ▫...
Page 528: Vehicle Identification Number
526 TECHNICAL DATA VEHICLE IDENTIFICATION NUMBER This number is also stamped on the floor of the passenger compartment, in front of the right front seat. The chassis number (VIN) and stamped on the plate illustrated in, located on the left front corner of the instrument panel cover, visible from the outside vehicle through the windshield.
Page 529: Wheel And Tire Torque Specifications
TECHNICAL DATA 527 WHEEL AND TIRE TORQUE SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench.
Page 530 528 TECHNICAL DATA WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.
Page 531: Fluid Capacities
TECHNICAL DATA 529 FLUID CAPACITIES Metric Fuel (Approximate) 1.4L Turbo/2.4L Engine 12.7 Gallons 48 Liters Engine Oil With Filter 1.4L Turbo Engine (SAE 5W-40 Synthetic, API Certified) 4.0 Quarts 3.8 Liters 2.4L Engine (SAE 0W-20, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 1.4L Turbo Engine (MOPAR Antifreeze/Engine Coolant 10 5.5 Quarts...
Page 532: Fluids, Lubricants, And Genuine Parts
530 TECHNICAL DATA FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meet- ing the requirements of FCA Material Standard MS.90032. Engine Oil –...
Page 533: Chassis
TECHNICAL DATA 531 Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If Equipped We recommend you use MOPAR C Series Manual & Dual Dry Clutch Transmission Fluid. Automatic Transmission – If Equipped Use only MOPAR ZF 8&9 Speed ATF Automatic Trans- mission Fluid, or equivalent.
Page 535 MULTIMEDIA CONTENTS CYBERSECURITY..... . .535 STEERING WHEEL AUDIO CONTROLS ..571 ▫ Radio Operation ..... .572 UCONNECT SETTINGS .
Page 536 534 MULTIMEDIA ▫ Radio ......578 ▫ Navigation (6.5AN) ....583 ▫...
Page 537: Cybersecurity
MULTIMEDIA 535 CYBERSECURITY The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent Your vehicle may be a connected vehicle and may be version of vehicle software (such as Uconnect software) is equipped with both wired and wireless networks.
Page 538: Uconnect Settings
536 MULTIMEDIA Privacy of any wireless and wired communications can- WARNING! (Continued) not be assured. Third parties may unlawfully intercept may increase the possibility for vehicle systems to information and private communications without your be breached. consent. For further information, refer to “Onboard Di- •...
Page 539 MULTIMEDIA 537 Uconnect 5.0 Buttons On The Touchscreen And Buttons Uconnect 6.5AN Buttons On The Touchscreen And On The Faceplate Buttons On The Faceplate 1 — Uconnect Buttons On The Touchscreen 1 — Uconnect Buttons On The Touchscreen 2 — Uconnect Buttons On The Faceplate 2 —...
Page 540: Buttons On The Faceplate
538 MULTIMEDIA Buttons On The Faceplate Buttons On The Touchscreen Buttons on the faceplate are located below, and beside the Buttons on the touchscreen are accessible on the Uconnect system in the center of the instrument panel. In Uconnect touchscreen. addition, there is a Scroll/Enter control knob located on Customer Programmable Features —...
Page 541 MULTIMEDIA 539 • Brightness your selection. Once the setting is complete, either press the Back Arrow button on the touchscreen or the Back When in this display, you may select the overall screen button on the faceplate to return to the previous menu or brightness with the headlights on or off.
Page 542 540 MULTIMEDIA • Fuel Consumption the “Touchscreen Beep” button on the touchscreen until a check-mark appears next to the setting, showing that Select from: “MPG” (US), “MPG” (UK), “L/100 km” setting has been selected. or “km/L.” • Pressure Units Select from: “psi,” “kPa,” or “bar.” After pressing the “Units”...
Page 543 MULTIMEDIA 541 • Show Command List • Show Time Status When in this display, you may change the Show Com- When in this display, you may turn on or shut off the mand List settings. To change the Show Command List digital clock in the status bar.
Page 544 542 MULTIMEDIA Safety/Assistance button on the touchscreen. Press the “Parkview Backup camera Delay” button on the touchscreen to turn the After pressing the “Safety/Assistance” button on the ParkView Delay ON or OFF. touchscreen the following settings will be available: • ParkView Backup Camera Active Guide Lines — If •...
Page 545 MULTIMEDIA 543 • Forward Collision Warning-Plus (FCW+) — If when the driver requests insufficient brake pressure to Equipped avoid a potential frontal collision. The ABA system becomes active at 5 mph (8 km/h). The Front Collision Warning (FCW+) feature can be can be set to Far, or set to Near.
Page 546 544 MULTIMEDIA • Front ParkSense Volume — If Equipped • LaneSense Warning — If Equipped Front Park Assist chime volume settings can be selected When this feature is selected, it sets the distance at which from the EVIC or Uconnect System (if equipped). The the steering wheel will provide feedback for potential chime volume settings include “LOW,”...
Page 547 MULTIMEDIA 545 • Blind Spot Alert — If Equipped NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is When this feature is selected, the Blind Spot Alert feature not damaged, the sensor may have become misaligned.
Page 548 546 MULTIMEDIA • Headlight Sensitivity engine is shut off. To change the Headlights Off Delay setting, press the Headlights Off Delay button on the When this feature is selected, it allows the Headlight touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 Sensitivity to be adjusted according to three levels: seconds.
Page 549 MULTIMEDIA 547 • Daytime Running Lights • Flash Lights With Lock — If Equipped When this feature is selected, the DRL will turn on while When this feature is selected, the exterior lights will flash the engine is running. To make your selection, press the when the doors are locked or unlocked with the Remote “Daytime Running Lights”...
Page 550 548 MULTIMEDIA • Auto Unlock On Exit is pressed. To make your selection, press the “Horn w/Lock” button on the touchscreen and select from When this feature is selected, all doors will unlock when Off,” “1st Press,” or “2nd Press” the vehicle is stopped and the transmission is in the •...
Page 551 MULTIMEDIA 549 • Remote Door Unlock/Door Unlock Engine Off Options After pressing the “Engine Off Options” button on the When “Driver” is selected, only the driver’s door will touchscreen the following settings will be available. unlock on the first push of the Remote Keyless Entry (RKE) transmitter UNLOCK button, you must push the •...
Page 552 550 MULTIMEDIA • Speed Adjusted Volume Audio After pressing the “Audio” button on the touchscreen the This feature increases or decreases volume relative to following settings will be available: vehicle speed. To change the Speed Adjusted Volume press the “Off,” “1,” “2” or “3” button on the touchscreen. •...
Page 553 MULTIMEDIA 551 To make your selection, press the “AUX Volume Offset” SiriusXM Setup — If Equipped button on the touchscreen, select “On” or “Off”. After pressing the “SiriusXM Setup” button on the touch- • Auto-On Radio screen, the following settings will be available: •...
Page 554 552 MULTIMEDIA Write down the SIRIUS ID numbers for your receiver. To “Cancel” or “X” to exit without making changes. Once reactivate your service, either call the number listed on the settings are restored, a pop up appears stating the screen or visit the provider online. Settings reset to default.
Page 555: Customer Programmable Features - Uconnect 6.5An Settings
MULTIMEDIA 553 Customer Programmable Features — Uconnect the Back Arrow button on the touchscreen to return to the 6.5AN Settings previous menu, or press the “X” button on the touch- screen to close out of the settings screen. Pressing the Up Press the Settings button to display the menu setting or Down Arrow button on the right side of the screen will screen.
Page 556 554 MULTIMEDIA • Display Brightness With Headlights ON • Set Language This feature will allow you to select the brightness with When in this display, you may select one of multiple the headlights on. Adjust the brightness with the “+” and languages (English/Español/Français) for all display no- “–”...
Page 557 MULTIMEDIA 555 Units Temperature — Select from: “°F” or “°C.” • Units Voice When in this display, you may select to have the Elec- After pressing the “Voice” button on the touchscreen the tronic Vehicle Information System (EVIC) or Driver In- following settings will be available: formation Display (DID), odometer, and navigation sys- •...
Page 558 556 MULTIMEDIA • Set Day Clock After pressing the “Clock” button on the touchscreen the This feature will allow you to set the day. To make your following settings will be available: selection, press the “–” or “+” buttons on the touchscreen to adjust the day up or down.
Page 559 MULTIMEDIA 557 • Set Hours Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button This feature will allow you to adjust the hours. The Sync on the touchscreen the following settings will be avail- Time with GPS “On” button must not be selected. To able: make your selection, press the “–”...
Page 560 558 MULTIMEDIA • Forward Collision Warning-Plus (FCW+) Active provide either an “early,” “medium,” or “late” warning Braking — If Equipped zone start point. To change the LaneSense Warning status, press the “LaneSense Warning” button and select The FCW+ system includes Advanced Brake Assist (ABA). from the “Early,”...
Page 561 MULTIMEDIA 559 • ParkSense — If Equipped • Front ParkSense Volume — If Equipped The ParkSense system will scan for objects behind the Front Park Assist chime volume settings can be selected vehicle when the transmission shift lever/gear selector is from the EVIC or Uconnect System (if equipped).
Page 562 560 MULTIMEDIA • ParkView Backup Camera Delay NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is When the vehicle is shifted out of REVERSE (with camera not damaged, the sensor may have become misaligned. delay turned OFF), the rear camera mode is exited and Take your vehicle to an authorized dealer to verify sensor the navigation or audio screen appears again.
Page 563 MULTIMEDIA 561 • Brakes • Rain Sensing Auto Wipers This feature provides a means for a technician or vehicle When this feature is selected, the system will automati- owner to utilize a vehicle integrated, menu driven sys- cally activate the windshield wipers if it senses moisture tem, to command the electric park brake retraction, to on the windshield.
Page 564 562 MULTIMEDIA • Headlight Off Delay Lights When this feature is selected, it allows the adjustment of After pressing the “Lights” button on the touchscreen the the amount of time the headlights remain on after the following settings will be available: engine is shut off.
Page 565 MULTIMEDIA 563 • Daytime Running Lights • Flash Lights With Lock When this feature is selected, the headlights will turn on When this feature is selected, the exterior lights will flash while the engine is running. To make your selection, when the doors are locked or unlocked with the Remote press the “Daytime Running Lights”...
Page 566 564 MULTIMEDIA • Flash Lights With Lock Doors & Locks After pressing the “Doors & Locks” button on the touch- When this feature is selected, the exterior lights will flash screen the following settings will be available: when the doors are locked with the Remote Keyless Entry (RKE) transmitter.
Page 567 MULTIMEDIA 565 • Sound Horn With Start — If Equipped • Passive Entry When this feature is selected, the horn will sound when This feature allows you to lock and unlock the vehicles the Remote Start is activated. To make your selection, door(s) without having to press the Remote Keyless press the “Sound Horn With Remote Start”...
Page 568 566 MULTIMEDIA NOTE: The seat will return to the memorized seat when exiting the vehicle. To change the Headlight Off location (if Recall Memory with Remote Key Unlock is set Delay status press the “+” or “–” button on the touch- to ON) when the Remote Keyless Entry (RKE) transmitter screen to select your desired time interval.
Page 569 MULTIMEDIA 567 • AUX Volume Offset — If Equipped NOTE: Bass/Mid/Treble allow you to simply slide your finger up or down to change the setting as well as press This feature provides the ability to tune the audio level directly on the desired setting. for portable devices connected through the AUX input.
Page 570 568 MULTIMEDIA • Paired Audio Sources services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. This feature shows which audio devices are paired to the Phone/Bluetooth system. Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen.
Page 571: Uconnect Radios
MULTIMEDIA 569 Clear Personal Data After pressing the “Clear Personal Data Settings” button on the touchscreen the following settings will be avail- able: • Clear Personal Data When this feature is selected it will remove personal data including Bluetooth devices and presets. To Clear Per- sonal Data press the “Yes”...
Page 572 570 MULTIMEDIA Refer to the Uconnect Radio Supplement for external USB support capability. Center Console USB Port Located in the center console is a second USB port. NOTE: Depending on vehicle configuration, the USB port may be charge only, or media file capable. Center Console USB (Charge Only) Port —...
Page 573: Steering Wheel Audio Controls
MULTIMEDIA 571 STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located at the rear mode of the sound system. Pushing the top of the rocker of the steering wheel.
Page 574: Radio Operation
572 MULTIMEDIA Radio Operation RADIO OPERATION AND MOBILE DEVICES Pushing the top of the switch will “Seek” up for the next Under certain conditions, the mobile device being on in listenable station and pushing the bottom of the switch your vehicle can cause erratic or noisy performance from will “Seek”...
Page 575 MULTIMEDIA 573 Nevertheless, the wireless radio will be used in such a 1. This device may not cause harmful interference. manner that the radio is 20 cm or further from the human 2. This device must accept any interference received, body.
Page 576: Uconnect Voice Recognition Quick Tips
574 MULTIMEDIA • If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •...
Page 577: Get Started
MULTIMEDIA 575 Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger con- versations are examples of noise that may impact recognition.
Page 578 576 MULTIMEDIA 5. You can interrupt the help message or system prompts by pushing the VR or Phone button and saying a Voice Command from current category. Uconnect Voice Command Buttons 1 — Push To Initiate Or To Answer A Phone Call, Send Or Re- ceive A Text 2 —...
Page 579: Basic Voice Commands
MULTIMEDIA 577 Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session. • Help to hear a list of suggested Voice Commands. •...
Page 580 578 MULTIMEDIA Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say •...
Page 581 MULTIMEDIA 579 Uconnect 5.0 Radio Uconnect 6.5AN Radio...
Page 582 580 MULTIMEDIA Media TIP: Press the Browse button on the touchscreen to see all of the music on your iPod or USB device. Your Voice Uconnect offers connections via USB Port, Bluetooth and Command must match exactly how the artist, album, Auxiliary Ports (If Equipped).
Page 583 MULTIMEDIA 581 Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illumi- nated on your touchscreen, your system is ready. Check UconnectPhone.com for mobile phone compatibility and pairing instructions. Push the Phone button .
Page 584 582 MULTIMEDIA TIP: When providing a Voice Command, push the Phone button and say “Call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.” Uconnect 6.5AN Phone Voice Text Reply Uconnect will announce incoming text messages.
Page 585 MULTIMEDIA 583 1. Once an incoming text message is read to you, push TIP: Your mobile phone must have the full implementa- the Phone button . After the beep, say: “Reply.” tion of the Message Access Profile (MAP) to take advan- tage of this feature.
Page 586 584 MULTIMEDIA 2. This device must accept any interference that may be received including interference that may cause unde- sired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not ex- pressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 587 MULTIMEDIA 585 Additional Information © 2015 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc.
Page 589 INDEX...
Page 590 588 INDEX About Your Brakes ......205 Air Bag Light .....173, 245, 272 Adding Engine Coolant (Antifreeze) .
Page 591 INDEX 589 Anti-Lock Warning Light....196, 197 Battery ......177, 468 Appearance Care .
Page 592 590 INDEX Caps, Filler Installing Child Restraints Using The Vehicle Seat Oil (Engine) ......466 Belt .
Page 593 INDEX 591 Connector Customer Assistance ......11 UCI ....... . .569 Customer Programmable Features .
Page 594 592 INDEX Driver’s Seat Back Tilt ..... . .63 Overheating ......431 Driving Towing .
Page 595 INDEX 593 Overheating ......431 Flooded Engine Starting ....280 Starting .
Page 596 594 INDEX Requirements ......342 Hazard Warning Flasher ....375 Specifications .
Page 597 INDEX 595 Hood Prop ......133 Jack Operation.....409, 413, 495 Hood Release .
Page 598 596 INDEX Key, Sentry (Immobilizer) ....46 Fog ........92 Hazard Warning Flasher .
Page 599 INDEX 597 Warning (Instrument Cluster Description) ..199 Shift Speeds ......293 Loading Vehicle .
Page 600 598 INDEX Disposal ......467 ParkSense System, Rear .....322 Filter .
Page 601 INDEX 599 Rear ParkSense System .....322 Remote Starting System..... .42 Rear Window Defroster .
Page 602 600 INDEX Seat Belt Operating Instructions ....221 Adjustable Upper Shoulder Belt Anchorage ..224 Pregnant Women ..... . .228 Automatic Locking Retractor (ALR) .
Page 603 INDEX 601 Shifting Steering Manual Transmission ....292 Tilt Column ......75 Shift Lever Override .
Page 604 602 INDEX Tire Markings ......497 Snow Tires ......513 Tires.
Page 605 INDEX 603 Minimum Requirements ....364 Uconnect Settings ......45 Trailer And Tongue Weight .
Page 606 604 INDEX Warranty Information .....4, 14 Washer Adding Fluid ......474 Washing Vehicle .
Page 607 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 608 16FB-126-AD 16FB-126-AA FCA US LLC ©2015 FCA US LLC. All Rights Reserved. Fourth Edition First Edition FIAT is a registered trademark of Fiat Group Marketing & Corporate Communication S.p.A., used under license by FCA US LLC. Printed in U.S.A.

Fiat 500 X 2016 Owner's Manual

Customer Assistance

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Cluster

Safety

Starting and Operating

In Case of Emergency

Maintaining and Caring for Your Vehicle

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Fiat 500 X 2016

Summary of Contents for Fiat 500 X 2016