Related Manuals for Sinclair DUCT ASD-09A
Summary of Contents for Sinclair DUCT ASD-09A
- Page 1 USER'S MANUAL DUCT SERIES ASD-09A, ASD-12A, ASD-18A, ASD-24A ASD-36A, ASD-41A, ASD-60A...
-
Page 3: Table Of Contents
Safety Considerations Turning On/Off Unit Temperature Setting Component Description Fan Control Sleep Function Setting Operating Mode Setting Timing Setting Fresh Air Valve Setting Operating Operating Energy Saving Setting Instructions Instructions for Line Display of Outdoor Ambient Temperature Controller Power-fail Memory Function Setting Debug Function Failure Display Operation of Remote Controller... -
Page 4: Safety Considerations
Safety Considerations Please read this manual carefully before use and operate correctly as instructed in the manual. 1． You are specially warned to note the two symbols below.: WARNING!：A symbol indicating that improper operation might cause human death or severe injuries. -
Page 8: Fresh Air Valve Setting
Operating Instructions of Wire Controller The range of set time is between 0.5 to 24 hours. 7）Fresh Air Valve Setting (Figure 8) When the unit is shut off, you can enter the fresh air setting by pressing and holding the “FAN” key for 5 consecutive seconds. - Page 9 Operating Instructions of Wire Controller modes of cooling and dehumidifying and turn to the energy saving setting for the heating mode (Cooling only unit does not have this function). Now the LCD displays “SAVE SET” and “HEAT”. After setting is completed, press the “FAN”...
-
Page 11: Failure Display
Operating Instructions of Wire Controller 12）Failure Display (Figure 13) When there is failure in the unit operation, “ERROR” will flash on the LCD of the wire controller and the code of failure will also be displayed. When there are multiple failures at the same time, the codes of failures will be displayed one after one on the wire controller. -
Page 13: Operation Of Remote Controller
Operation of Remote Controller DRY (Dehumidifying) Mode Operations Connect the unit to power supply. Press the “ON/OFF” key. Press the “MODE” key to select “DRY (Dehumidifying)” mode. Use the “Temperature” key to adjust the set temperature for the room. Refer to Figure 17. - Page 14 Operation of Remote Controller 1.All the prints and code no. will be showed on the displayer after the insert of batteries. The remote control can be operated after 10sec. 2.The lifetime of the batteries is about one year 3.Don't confuse the new and worn or different types of batteries.
-
Page 15: Unit Function
Unit Function Weekly Timer 1. Week Timing Controller (With Centralized Control Function) Centralized Control and Week Timer Functions: The centralized controller and the weekly timer are integrated in the same wire controller. The system has both the centralized control and the week timing functions. - Page 16 Unit Function Setting of Indoor Room Sensor and Checking of Outdoor Ambient Temperature Note: 1． For upper unit checks 16 lower units consecutively, there will be no more than 16 seconds delay when setting works till unit responds. Please let us know your requirement before your placing the order, for this WEEKLY TIMER will only be prepared when customer orders (communication joint with WEEKLY TIMER on manual control had been prepared).
-
Page 17: Indoor Side
Unit Function Fresh Air Control, Pump 4. Fresh Air Control 11-level control can be realized for the amount of fresh air taken in. The function not only facilitates the health of users, but also controls the electricity consumption loss because of taking in fresh air. This kind of control can be carried out through the wire controller. - Page 18 Instructions of Unit Installation Profile Dimensions of Indoor Unit Profile Dimensions of Indoor Unit E le ctric B o x L iq u id P ip e G a s P ip e A ir In ta k e D ra in a g e P ip e A ir In ta k e ：...
- Page 19 Instructions of Unit Installation Profile Dimensions of Indoor Unit Profile Dimensions of Indoor Unit Item Model ASD-09A 1/4〞 3/8〞 ф20×1.5 ASD-12A ASD-18A 1/4〞 1/2〞 ф30×1.5 ASD-24A 1063 1159 1270 1088 3/8〞 5/8〞 ф20×1.5 ASD-36A 1011 1115 1251 1047 1/2〞 3/4〞 ф20×1.5 ASD-41A ASD-60A...
-
Page 20: Installation Of Outdoor Unit
Instructions of Unit Installation Profile Dimensions of Outdoor Unit 2. Profile Dimensions of Outdoor Unit Unit：mm Fig. 30 Model ASD-09A ASD-41A ASD-36A ASD-12A ASD-24A ASD-60A ASD-18A Item 760/848 1250 Fig.31 Unit Installation Instructions Precautions on Installation of Outdoor Unit To ensure the unit in proper function, selection of installation location must be in accordance with following principles: (1) Outdoor unit shall be installed so that the air discharged by outdoor unit will not return and that sufficient space for repair shall be provided around the machine. -
Page 21: Selection Of Installation Site
Unit Installation Instructions Installation of Indoor Unit (4) Avoid direct sunshine over the unit. It is better to set up a sun shield as the protection. (5) Place of installation must be able to drain the rainwater and defrosting water. (6) Place of installation must ensure the machine will not be buried under snow or subject to the influence of rubbish or oil fog. - Page 22 Unit Installation Instructions Inspection of Level of Indoor Unit, Fabrication of Backwater Elbow Precautions: 1. The preparation of all pipes (connecting pipes and drainage pipes) and cables (connecting lines of wire controller, indoor unit and outdoor unit) must be ready before the installation, so as to achieve smooth installation.
- Page 23 Unit Installation Instructions Installation of Condensate Pipe Cautions: The air supply pipe, the air intake pipe and the fresh air pipe must be covered with a layer of thermal insulation, so as to avoid thermal leakage and condensation. Firstly apply liquid nail on the pipes, then attach the thermal insulation cotton with a layer of tinfoil.
- Page 24 Unit Installation Instructions Installation of Condensate Pipe and the flexible drainage tube. (4) When the laid drainage pipe is used for multiple units, the common pipe shall be about 100mm lower than the drainage outlet of each set of unit. A pipe with thicker wall shall be used for such purpose.
- Page 25 Instructions of Unit Installation Connection of Pipelines Connection of Pipeline 1. Align the flared end of the copper pipe with the center of the thread joint. Manually tighten the flared end nut. 2. Use torque spanner to tighten the flared end nut until the spanner clatters (Figure 38). One-Way Valve Gas Valve Liquid Valve...
- Page 26 Instructions of Unit Installation Installation of Connecting Pipe 10. If conditions allow, use a vacuum pump to remove air out from the valve. Refer to Figure 40 Pressure Gage Pressure Gage “HI” Knob “LO” Knob Liquid Valve Vacuum Pump Connecting Hose Gas Valve Fig.40 1.
-
Page 27: Position And Method Of Installing Wire Controller
Instructions of Unit Installation Installation of Connecting Pipe （2） Use thermal insulation tape to wrap the pipes from the bottom of the outdoor unit until the upper end of the pipe where the pipe enters the wall. When wrapping thermal insulation tape, the later circle of tape must cover half of the front circle of tape (Refer to Figure 42). - Page 28 Instructions of Unit Installation Installation of Wire Controller Electric box cover sketch map for indoor unit communication wire Wire clamp Cable-cross loop Control wire Communication wire metallic pipe metallic pipe Figure 43 Surface Figure 44 Concealed Figure 45 Schematic Diagram of Installation Mounting of Cable mounting of Cable Name...
- Page 29 Instructions of Unit Installation Electrical Installation Caution: Before installing the electrical equipment, please pay attention to the following matters which have been specially pointed out by our designers: （1） Check to see if the power supply used conforms to the rated power supply specified on the nameplate.
-
Page 30: Electrical Installation
Instructions of Unit Installation Electrical Installation (4 ) Use cable fastener to bundle and fix the cable. 2。 Air-conditioning unit with 3-phase power supply Caution: （1） Remove the front-side panel of the outdoor unit. Take great care when carrying out the following （2）Attach rubber ring to the cable-cross hole of the connections, so as to avoid malfunction of the outdoor unit. -
Page 32: Routine Maintenance
Note: After carrying out the check of the above items and taking relevant measures to solve the problems found but the air-conditioning unit still does not function well, please stop the operation of the unit immediately and contact the local service agency designated by SINCLAIR. Only ask professional serviceman to check and repair the unit. -
Page 33: Troubleshooting And Maintenance
Instructions of Unit Installation Troubleshooting and Maintenance 4) Take care when cleaning the air-conditioning unit. Use a steady stepping stand. 2. Maintenance at the Beginning of Operating Season (1) Check the air inlet and outlet of the indoor and outdoor units to confirm there is no blockage. (2) Check to see if the grounding wire is in good condition;... - Page 34 Performance Parameters Sheet Continued Heat pump type Model ASD-09A ASD-12A ASD-18A ASD-24A ASD-36A ASD-41A ASD-60A Item 7000 10000 12000 16000 Cooling Capacity 2600 3500 5000 8000 11000 14500 19000 Heating Capacity 2900 3700 5800 2800 4050 5300 6500 Cooling 1300 2100 2400 3300...
- Page 35 Appendix: Air conditioner nominal working condition and working range: Indoor side Outdoor side Test condition DB(℃) WB(℃) DB(℃) WB(℃) Nominal cooling Nominal heating ―― Max. cooling Low temp. cooling －7 ―― Max. heating ―― Low temp. heating ―― －7 －8 Note: 1.
-
Page 36: Environmental Information
ENVIRONMENTAL INFORMATION This unit contains fluorinated gases with greenhouse effect covered by the Kyoto Protocol. Maintenance and disposal must be carried out by qualified persons only. Refrigerant gas R410A, GWP = 1730 EXTRA REFRIGERANT CHARGE Pursuant to Regulation EC 842/2006 on certain fluorinated greenhouse gases, in case of extra refrigerant charge, it is compulsory to: Fill in the label accompanying the unit inserting the factory quantity of refrigerant charge (see the technical label), the extra refrigerant charge and the total charge. - Page 37 This product must not be disposed together with the domestic waste. This product has to be disposed at an authorized place for recycling of electrical and electronic appliances. 66175604...
Need help?
Do you have a question about the DUCT ASD-09A and is the answer not in the manual?
Questions and answers