Dimplex CDFI1000P Service Manual

Dimplex CDFI1000P Service Manual

Part number 6909660100
Hide thumbs Also See for CDFI1000P:

Advertisement

IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this cassette. For your
safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or prop-
erty damage.
Dimplex North America Limited
1367 Industrial Road Cambridge ON Canada N3H 4W3
1-888-346-7539 www.dimplex.com
In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
© 2015 Dimplex North America Limited
Service Manual
Model
CDFI1000P
Part Number
6909660100
REV
PCN
DATE
00
-
21-12-15
7400880000R00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CDFI1000P and is the answer not in the manual?

Questions and answers

Summary of Contents for Dimplex CDFI1000P

  • Page 1 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N3H 4W3 21-12-15 1-888-346-7539 www.dimplex.com In keeping with our policy of continuous product development, we reserve the right to make changes without notice. © 2015 Dimplex North America Limited 7400880000R00...
  • Page 2: Table Of Contents

    NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment. WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death. www.dimplex.com...
  • Page 3: Operation

    OPERATION Figure 2 Figure 1 Tethered Controller WARNING: This electric firebox must be properly in- NOTE: The icons stalled before it is used. with 1 dot indicate con- The unit has two separate internal modules that are con- trols for the primary and Remote trolled by the settings entered on the left side (primary).
  • Page 4: Maintenance

    7. Turn the On/Off switch to the off position (I) . (Figure 1A) 8. Gently place the top tray back into position. If you do not intend on using the unit for longer than 2 www.dimplex.com...
  • Page 5: Exploded Parts Diagram

    EXPLODED PARTS DIAGRAM REPLACEMENT PARTS LIST 11. Fan Filter ......8600300100RP 1. Main Control Board ....9601270100RP 12.
  • Page 6: Wiring Diagram

    WIRING DIAGRAM www.dimplex.com...
  • Page 7: Switch Board Replacement

    SWITCH BOARD REPLACEMENT TERMINAL BLOCK REPLACEMENT Tools Required: Phillips head screwdriver Tools Required: Phillips head screwdriver WARNING: Disconnect power before attempting any WARNING: Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage maintenance to reduce the risk of electric shock or damage to persons.
  • Page 8: Fan Assembly Replacement

    7. Run wiring back to location for fan, and install the fan. NOTE: Ensure that all of the components that con- tain water have been emptied and source water has been 8. Reinsert the electronics assembly. turned off before performing any maintenance. www.dimplex.com...
  • Page 9: Power Supply Replacement

    Primary Side block have not moved from their original locations and all wires are contained under the cover before reassembly. 1. Disconnect and remove the media tray or log set from 8. Re-assemble the remainder of the cassette in reverse the unit and put them in a safe place.
  • Page 10: Led Light Assembly Replacement

    CAUTION: Ensure that the switchboard and terminal through the opening on the secondary side to allow the pri- block have not moved from their original locations and all mary electronics assembly to be lifted out. www.dimplex.com...
  • Page 11: Level Sensor Assembly Replacement

    6. Locate the 2 screws that secure the element assembly wires are contained under the cover before reassembly. (element and brackets) to the unit and remove. 11. Re-assemble the remainder of the cassette in reverse 7. Lift the element assembly out of the unit. order from the instructions above.
  • Page 12: Solenoid Valve Replacement

    12. Re-assemble the remainder of the cassette in reverse 4. Remove the cable clamp, to allow for the assembly to order from the instructions above. www.dimplex.com...
  • Page 13: Troubleshooting Guide

    TROUBLESHOOTING GUIDE ** After the unit has shut down due to an error, a full reset of the unit will be required by turning the unit Off with the On/ Off switch for 60 seconds then turning back On. PROBLEM CAUSE SOLUTION General...
  • Page 14 Water is appearing beneath Connections are leaking Ensure that all water connections are tight and fully unit inserted Incoming water pressure is too high (only ap- Reduce water pressure to below 58 psi (8 bar) plicable on hard plumbed units) www.dimplex.com...
  • Page 15 PROBLEM CAUSE SOLUTION Appearance Continued Unit is blinking every 8 sec- Water level in reservoir is too high ** Remove enough water from reservoir so that level is onds and is not operating below maximum level The solenoids are not operating correctly - put If the solenoids are not working, replace the solenoid unit in troubleshooting mode to test the opera- tion of the solenoids...

Table of Contents