Page 1
Compel web site at: www.wegener.com. WEGENER Unpacking and Inspection The box containing the unit should include: iPump 562 Media Server Quick Start Guide Two rack mounting brackets Safety Instructions Inline power supply and power cord Optional Remote Control with two AA batteries and...
Page 2
7.5 pounds or 3.4019 kilograms Dimensions (H x W x D) 1RU (1.75"x 16.5"x 11.5" or 44.45 mm x 419.1 mm x 292.1 mm) Input Power Rating for iPump 562 12VDC 5.0A Input Power Rating for inline power 100-240VAC, 50/60Hz, 1.5A...
Page 3
562 branch circuit, as well as the power source, will not be overloaded. Also make sure that the unit is properly grounded and/or that a protected power strip is used to attach it to the power supply.
Page 4
Alarm relay Normally Closed Alarm relay Normally Open User relay Normally Closed User relay Common User relay Normally Open No Connection Ground GPIO Input Do not connect RJ-12 directly to phone line. Equipment damage may result. AUTION: 800092-02 Rev. C www.wegener.com...
Page 5
, local terminal, and . Normally, is the Compel network control On-Screen-Display Compel primary method of controlling the iPump562. Front Panel iPump 562 right arrow button t arrow button top arrow button bottom arrow button Enter button LCD screen...
LCD as shown above. The LCD single line iPump 562 display will display the current OSD line. The up/down arrows will navigate from line to line. The left/right arrows will navigate through fields.
Page 7
Navigates to the carrier settings menu, which allows viewing/changing the tuned RF carrier settings, LNB parameters, signal quality alarm settings and a signal strength meter. Advanced Navigates to the advanced menu, which allows more detailed monitor and control functions, such as viewing software versions, decoder setup, and audio setup. www.wegener.com 800092-02 Rev. C...
Page 8
The alarm level is based on the modulation format and FEC rate. Signal Quality Setup Allows editing of the number of errored seconds per minute at which to display an alarm. Signal Strength Meter Displays a meter showing signal strength and Eb/No to aid in antenna peaking. 800092-02 Rev. C www.wegener.com...
Page 9
CC1-4. CC1-4 may be selected only if subtitling is disabled. Composite/S-Video Selects video output format for the composite video outputs and S-video output (if available). SD Aspect Ratio Selects the aspect ratio for the composite video outputs and S-video output (if available). www.wegener.com 800092-02 Rev. C...
Page 10
HDMI Auto-Negotiate When enabled, the output resolution and refresh rate of the component and HDMI outputs are set per the DDC data received from the TV. HDMI Out Displays current mode/resolution of the component and HDMI outputs. 800092-02 Rev. C www.wegener.com...
Page 11
The status view displays the current status of the unit, including the serial number, software versions installed, decoder status, Compel statistics, RF signal information, and file download status. The green LED icon will indicate the state of the LED on the unit and clicking this will show any warnings or alarms, if present. www.wegener.com 800092-02 Rev. C...
Page 12
The file manager view allows the user to view the assets currently on the unit. Assets are user provided video, audio, image, or text files downloaded via Compel. Click the assets folder to view the list of assets. Assets may be viewed, played or downloaded by clicking on the file name. 800092-02 Rev. C www.wegener.com...
Page 13
The logs view allows the user to view the “as run” log or the “operational” log. The “as run” log lists all assets that have been played by the unit. The “operational” log lists any changes in RF signal tuning. www.wegener.com 800092-02 Rev. C...
Page 14
UIDE Diagnostics interface By holding down the control key on the keyboard and clicking the Wegener logo in the top left corner, a diagnostics interface may be accessed. From this interface, in addition to many other actions, the user can play a file or playlist of files from the hard disk drive.
Page 15
Placing a unit in internet mode means that the unit will not attempt to tune and will ignore tuner alarms. To place the unit in internet mode issue the following commands: “carrierreq 0” “srchman tunerignore 1” “reset” To revert to normal RF operation issue the commands: “carrierreq 1” “srchman tunerignore 0” “reset” www.wegener.com 800092-02 Rev. C...
Page 16
IP address must be set in the unit that matches the Compel IP address. This is done with the command: cmplint srvraddr [address] , where [address] is the Compel IP address. Assets will also be retrieved via this server address. 800092-02 Rev. C www.wegener.com...
WEGENER All WEGENER products are warranted against defective materials and workmanship for a period of one year after shipment to customer . Wegener Communications ' obligation under this warranty is limited to rep airing or , at W egener Communications' option, replacing p arts, subassemblies, or entire assemblies.