Advertisement
When you are finished exercising, stop the
5
walking belt and remove the key.
Step onto the foot rails, slide the speed control to
the reset position, and remove the key from the
console. The displays will turn off a few minutes
after the key is removed. Note: Any time that the
walking belt is stopped and the ON/RESET
button is not pressed for a few minutes, the
displays will automatically turn off to con-
serve the batteries.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are four incline levels.
Before changing the incline, remove the key and
unplug the power cord. Next, fold the treadmill to the
storage position (see the section below).
To change the incline, first remove the incline pin from
the right incline leg as shown at the right. Adjust the in-
cline leg to the desired height and fully reinsert the in-
cline pin. Make sure that the incline pin is in the
"locked" position shown in the inset drawing.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Press out on the latch. Raise the tread-
mill until the storage latch closes over the catch. Make
sure that the storage latch is fully engaged over the
catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30° C (85° F)
Fahrenheit.
Incline
Pin
Incline
Pin
Incline
Pin
Right
Incline
Leg
Adjust the left incline leg in the same manner. Make
sure that both incline pins are inserted from the di-
rection shown.
CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline
pins removed. After you have adjusted the incline
legs, lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 11).
Engaged
Storage
Latch
Catch
10
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBE
TM
WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBE
TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such
substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor and an earth-
ing plug.
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1, and plug the indicated end of the
power cord into the socket on the treadmill. Next, lift the indi-
cated tab on the ferrite box and clamp the ferrite box around
the power cord. The ferrite box should not be allowed to slide
along the power cord. Fasten the included plastic tie just be-
hind the ferrite box and cut off the excess plastic tie. Refer to
drawing 2. Plug the power cord into an appropriate outlet that
is properly installed and earthed in accordance with all local
codes and ordinances. Note: In Italy, an adaptor (not included)
must be used between the power cord and the outlet.
Important: The treadmill is not compatible with GFCI-equipped
outlets.
If the power cord is damaged, it must be replaced with a manufac-
turer-recommended power cord.
DANGER:
Improper connection of the
equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not mod-
ify the plug provided with the product—if it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
TM
, a high-performance lubricant. IMPOR-
1
Socket on treadmill
Ferrite Box
Plastic
Tab
2
Outlet
7
Tie
Advertisement
