Toro 38536 Operator's Manual
Hide thumbs Also See for 38536:

Advertisement

Quick Links

CCR
Snowthrower
Model No. 38536—Serial No. 230000001 and Up
Introduction
Read this manual carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for
operating the product properly and safely.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. The
illustration below identifies the location of the model
and serial numbers on the product. Write the numbers
in the space provided below:
Model #:
Serial #:
This manual identifies potential hazards and has
safety messages identified by the following words:
Danger signals an extreme hazard that will
cause serious injury or death if you do not follow
the recommended precautions.
Warning signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
Caution signals a hazard that may cause minor
or moderate injury if you do not follow the
recommended precautions.
This manual uses 2 other words to highlight
information. Important calls attention to special
mechanical information and Note: emphasizes
general information worthy of special attention.
Safety
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
Printed in USA
Original Instructions (GB)
2450 GTS
Improperly using or maintaining this
snowthrower could result in injury or death. To
reduce this potential, comply with the following
safety instructions.
The following instructions have been adapted from
the ANSI/OPEI standard B71.3–1995 and the ISO
8437:1989 standard.
Training
Preparation
– Use an approved fuel container.
– Never add fuel to a running or hot engine.
– Fill the fuel tank outdoors with extreme care.
– Replace the fuel tank cap securely and wipe up
3327-933
Operator's Manual
Read the operator's manual carefully. Be
thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
Never allow children to operate the snowthrower.
Never allow adults to operate the snowthrower
without proper instruction.
Keep the area of operation clear of all persons
(particularly small children) and pets.
Exercise caution to avoid slipping or falling.
Thoroughly inspect the area where you will use
the snowthrower. Remove all doormats, sleds,
boards, wires, and other foreign objects.
Release the control bar to disengage the rotor
blades before starting the engine.
Do not operate the snowthrower without wearing
adequate winter garments. Wear footwear that
will improve your footing on slippery surfaces.
Handle fuel with care; it is highly flammable.
Never fill the fuel tank indoors.
any spilled fuel.
Use only the power cord supplied with the
snowthrower and a receptacle appropriate for use
with the power cord for electric-start motors.
Never attempt to make any adjustments while the
engine is running, except where specifically
recommended by Toro.
2002 by The Toro Company
All Rights Reserved
Form No. 3327-933

Advertisement

Table of Contents
loading

Summary of Contents for Toro 38536

  • Page 1 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Training Dealer or Toro Customer Service and have the model and serial numbers of your product ready. The Read the operator’s manual carefully. Be illustration below identifies the location of the model thoroughly familiar with the controls and the and serial numbers on the product.
  • Page 2: Maintenance And Storage

    The following list contains safety information specific If the unit should start to vibrate abnormally, stop to Toro products or other safety information that you the engine and check immediately for the cause. must know.
  • Page 3 Directive 2000/14/EC. container. Remove the key from the ignition switch before storing the snowthrower. Vibration Purchase only genuine Toro replacement parts and accessories. This unit does not exceed a hand/arm vibration level of 15.5 m/s , based on measurements of identical machines per Directive 98/37/EC.
  • Page 4 105-1979 1. Choke 2. Use unleaded gasoline; 50:1 gas:oil mixture. 3. To start the engine, move the choke to the right, push the primer twice, turn the key, and push the choke left after it starts. 4. Read the Operator’s Manual. 105-3524 1.
  • Page 5: Product Overview

    Product Overview Setup Installing the Wheels 1. Turn the snowthrower onto its left side and place a block under the left axle end. 2. Slide the short spacer (A) and a wheel onto the right axle end. Note: The side of the wheel with 6 spokes must face downward.
  • Page 6: Before Starting

    Installing the Handle Installing the Discharge Chute 1. Cut the plastic tie that secures the control cable to the handle. Install the discharge chute as shown. 2. Position the upper handle as shown. 3. Loosely install the handle bolts, curved washers, and knobs as shown.
  • Page 7: Mixing Gasoline And Oil

    Mixing Gasoline and Oil Operation This snowthrower uses a 50:1 gasoline-to-oil mixture. Note: Determine the left and right sides of the Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) machine from the normal operating position. or an equivalent high-grade, NMMA TCW-certified two-cycle oil.
  • Page 8: Adjusting The Discharge Chute

    Caution Adjusting the Discharge Chute If you leave the snowthrower plugged into a power outlet, someone can inadvertently start the To adjust the discharge chute, move the chute handle snowthrower and injure people or damage (A) and the chute deflector handle (B) as shown. property.
  • Page 9: Recommended Maintenance Schedule

    Preventing Freeze-up after Use With the engine off, pull the recoil starter handle several times to prevent the recoil starter from Let the engine run for a few minutes to prevent freezing up. moving parts from freezing. Stop the engine, wait for all moving parts to stop, and remove ice and snow from the snowthrower.
  • Page 10: Inspecting The Rotor Blades

    Adjusting the Cable Inspecting the Rotor Blades 1. Unhook the end of the control cable from Before each season, inspect the rotor blades for the control bar. wear. When a rotor blade edge has worn down to the wear indicator hole (A), have an Authorized Service Dealer replace the rotor blades and the scraper.
  • Page 11 This can damage the chute handle. 1. Add a fuel stabilizer/conditioner to the fuel in the fuel tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel stabilizer/conditioner.

This manual is also suitable for:

Ccr 2450 gts

Table of Contents