Toro 38537 Operator's Manual
Hide thumbs Also See for 38537:

Advertisement

CCR
Snowthrower
Model No. 38537—Serial No. 240000001 and Up
Introduction
Read this manual carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for
operating the product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. The
illustration below identifies the location of the model
and serial numbers on the product. Write the numbers
in the space provided below:
Model #:
Serial #:
This manual uses 2 words to highlight information.
Important: calls attention to special mechanical
information and Note: emphasizes general
information worthy of special attention.
Safety
This snowthrower meets or exceeds the ISO
standard 8437 in effect at the time of production.
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
Improperly using or maintaining this
snowthrower could result in injury or death. To
reduce this potential, comply with the following
safety instructions.
The following instructions have been adapted from
the ANSI/OPEI standard B71.3–1995 and the ISO
8437:1989 standard.
2003—The Toro Company
8111 Lyndale Ave., Bloomington, MN 55420, USA
3650 GTS
Training
Preparation
– Use an approved fuel container.
– Never add fuel to a running or hot engine.
– Fill the fuel tank outdoors with extreme care.
– Replace the fuel tank cap securely and wipe up
Printed in the USA
All Rights Reserved
Operator's Manual
Read the operator's manual carefully. Be
thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
Never allow children to operate the snowthrower.
Never allow adults to operate the snowthrower
without proper instruction.
Keep the area of operation clear of all persons
(particularly small children) and pets.
Exercise caution to avoid slipping or falling.
Thoroughly inspect the area where you will use
the snowthrower. Remove all doormats, sleds,
boards, wires, and other foreign objects.
Release the control bar to disengage the rotor
blades before starting the engine.
Do not operate the snowthrower without wearing
adequate winter garments. Wear footwear that
will improve your footing on slippery surfaces.
Handle fuel with care; it is highly flammable.
Never fill the fuel tank indoors.
any spilled fuel.
Use only the power cord supplied with the
snowthrower and a receptacle appropriate for use
with the power cord for electric-start motors.
Never attempt to make any adjustments while the
engine is running, except where specifically
recommended by Toro.
Let the engine and the snowthrower adjust to the
outdoor temperature before starting to clear
snow.
Operating any powered machine can result in
foreign objects being thrown into the eyes.
Always wear safety glasses or eye shields while
operating, adjusting, or repairing the
snowthrower.
Original Instructions (GB)
Register your product at www.Toro.com
Form No. 3329-465

Advertisement

Table of Contents
loading

Summary of Contents for Toro 38537

  • Page 1 (particularly small children) and pets. additional information, contact an Authorized Service Exercise caution to avoid slipping or falling. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. The Preparation illustration below identifies the location of the model and serial numbers on the product.
  • Page 2: Maintenance And Storage

    Stop the engine whenever you leave the The following list contains safety information specific operating position, before unclogging the to Toro products or other safety information that you discharge chute, and when making any repairs, must know. adjustments, or inspections.
  • Page 3: Sound Pressure

    Store fuel in an approved fuel container. Remove the key from the ignition switch before storing the snowthrower. Vibration Purchase only genuine Toro replacement parts and accessories. This unit does not exceed a hand/arm vibration level of 15.5 m/s , based on measurements of identical machines per Directive 98/37/EC.
  • Page 4 105-1979 1. Choke 2. Use unleaded gasoline; 50:1 gas:oil mixture. 3. To start the engine, move the choke to the right, push the primer twice, turn the key, and push the choke left after it starts. 4. Read the Operator’s Manual. 105-3522 1.
  • Page 5: Product Overview

    Product Overview Setup Installing the Wheels 1. Turn the snowthrower onto its left side and place a block under the left axle end. 2. Slide the short spacer (A) and a wheel onto the right axle end. Note: The side of the wheel with 6 spokes m-6230a must face downward.
  • Page 6: Installing The Handle

    Installing the Handle Installing the Discharge Chute 1. Cut the plastic tie that secures the control cable to the handle. Install the discharge chute as shown. Note: Hold the cable taut to ensure that it stays disconnected at the bottom. 2.
  • Page 7: Before Starting

    Mixing Gasoline and Oil This snowthrower uses a 50:1 gasoline-to-oil mixture. Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) or an equivalent high-grade, NMMA TCW-certified two-cycle oil. Important: To prevent engine damage, do not use automotive oil (such as SAE 30 or 10W30) or fuel mixed at the wrong gasoline-to-oil ratio.
  • Page 8: Operation

    Starting the Rotor Blades Operation To start the rotor blades, hold the control bar against Note: Determine the left and right sides of the the handle. machine from the normal operating position. Starting the Engine 1. Turn the ignition key clockwise to the On position.
  • Page 9: Adjusting The Discharge Chute

    Adjusting the Discharge Preventing Freeze-up after Use Chute Let the engine run for a few minutes to prevent moving parts from freezing. Stop the engine, wait for all moving parts to stop, and remove ice and To adjust the discharge chute, rotate the chute crank snow from the snowthrower.
  • Page 10: Recommended Maintenance Schedule

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Check the control cable both initially and after the first hour of operation; adjust it if necessary. Initially Check for loose fasteners and tighten them if necessary.
  • Page 11: Adjusting The Cable

    Adjusting the Cable Inspecting the Rotor Blades 1. Unhook the end of the control cable from Before each season, inspect the rotor blades for the control bar. wear. When a rotor blade edge has worn down to the wear indicator hole (A), have an Authorized Service Dealer replace the rotor blades and the scraper.
  • Page 12: Folding The Handle

    This can damage the chute handle. 1. Add a fuel stabilizer/conditioner to the fuel in the fuel tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel stabilizer/conditioner.

This manual is also suitable for:

Ccr 3650 gts

Table of Contents