Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco S150XT 05131501
Summary of Contents for Peco S150XT 05131501
- Page 1 P P P PTO GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM DESIGNED TO FIT: S150XT 2012-2013 MODEL #: 05131501 6.5HP BRIGGS & STRATTON VANGUARD MODEL #: 05131502 900 SERIES BRIGGS & STRATTON OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0462...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Introduction and Description 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Left & Right Frame Bracket Installation
2-2 Left and Right Frame Bracket Installation Secure the left frame bracket P#(B0801) and right frame bracket P#(B0802) to the rear frame of the mower where the rear bumper was removed. Use the existing hardware from the rear bumper as shown in Figure 2-2. Figure 2-2 Existing Hardware... -
Page 7: Rear Frame Bracket Installation
2-3 Rear Frame Bracket Installation 2-4 Muffler Guard Bracket Installation Attach the rear frame bracket P#(B0803) to the left and Attach (2) muffler guard brackets P#(B0806) to the rear right frame bracket using (2) 3/8”-16 x 1” HHCS frame bracket using (1) 1/4”-20 x 3/4” HHCS P#(K1222) P#(K1191) and (2) 3/8”-16 nylon flange locknuts and (1) 1/4”-20 nylon flange locknut P#(K2014) PER P#(K2038). -
Page 8: Outer Engine Mount Tube
2-5 Outer Engine Mount Tube 2-6 Engine Mount Arm Assembly Installation Installation Secure the outer engine mount tube P#(B3727) to the Insert the engine mount arm assembly P#(A0274) into rear frame bracket using (2) 3/8”-16 x 3” u-bolts the outer engine mount tube and secure with (1) detent P#(K1432) and (4) 3/8”-16 nylon flange locknuts pin P#(J0248). -
Page 9: Engine/Blower/Blade Assembly Installation
2-7 Engine/Blower/Blade Assembly Installation Place the engine/blower/blade assembly on top of the engine mount arm assembly as shown in Figure 2-7a. Secure the assembly using (4) 5/16”-18 x 1-1/2” HHCS P#(K1157) and (4) 5/16”-18 nylon flange lock nuts P#(K2516) as shown in Figure 2-7b. Adjust the position of the outer engine mount tube so that the blower housing has at least 1”... -
Page 10: Lower Mount Tube & Upper Frame Assembly Installation
2-8 Lower Mount Tube and Upper Frame Assembly Installation Position the (2) lower mount tubes P#(B0752) on top of the tabs located on the rear frame bracket. Secure each lower mount tube to the rear frame bracket using (2) 5/16”-18 u-bolts P#(K1098) and (4) 5/16”-18 nylon flange locknuts P#(K2516). -
Page 11: Top Assembly To Upper Frame Assembly Installation
2-9 Top Assembly To Upper Frame 2-11 Inlet Installation Assembly Installation Slide the inlet P#(V0025) into the hole on the bagger top Position the top assembly P#(A1158) above the upper until the inlet locks into place. The inlet should pivot 360 frame assembly as shown in Figure 2-9. -
Page 12: Blower Cone Installation
2-13 Blower Cone Installation 2-14 Boot To Mower Deck Installation Lift the grass deflector on the discharge chute. Insert (1) Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of boot rod P#(B0348) through the outside set of mounting (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially holes on the deflector bracket, as shown in Figure 2-14a. -
Page 13: Length Of Hose Adjustment
2-15 Length Of Hose Adjustment 2-17 Lower Hose To Blower Cone Installation The hoses in steps 2-16 and 2-17 must be cut to fit your machine. Follow steps 2-16 and 2-17. do not cut the Slide a 8” hose clamp P#(J0080) over both ends of the hoses until you have tried to fit them on your machine. -
Page 14: Impeller Blade Removal/Replacement
2-19 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the 1 - Try carefully hitting the base of the impeller blade blower cone (#2) from the blower housing, located on (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 15: Weight Kit Installation
2-20 Weight Kit Installation The collection system requires that a weight kit is Position (1) weight bar P#(B2220) on top of the weight installed to the front of the mower to counter-balance the bracket as shown in Figure 2-20b. Center the weight bar weight of the collection system, when filled with debris. -
Page 16: Installation/Removal Of Collection Bags
2-21 Installation/Removal Of Figure 2-21c Collection Bags Plastic Top IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure 2-21a, on each bag ring before installing bags. Figure 2-21a Bag Ring Red Plastic End Caps Fasten Draw -Latch Here &... -
Page 17: Throttle Cable Installation
2-22 Throttle Cable Installation To install the throttle cable kit to the ROPS (roll over Figure 2-22c protection system), place the 3/8” U-Bolt P#(K0136) onto the ROPS with the threads facing the front of the mower. Next slide on the throttle mount plate assembly P#(A0666) with the rivets also facing toward the front of From the mower. -
Page 18: Exploded Part Views And Assemblies
Exploded Parts View A1158 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"... -
Page 21: Operating Instructions
3-3 Disengagement Of The Blower SECTION III Briggs & Stratton 900 Series - To stop the engine, OPERATING INSTRUCTIONS throttle the engine to the stop position. 6.5HP Briggs & Stratton Vanguard - To stop the engine, move the fuel lever to the OFF position. 3-1 General Safety 3-4 Unloading The Collection System Only qualified people familiar with this operator’s manual... -
Page 22: Parts And Service
4. Listen for abnormal sounds, which might indicate loose parts, damaged bearings, or other damage. Correct any deficiency before continuing operation. PECO collection system owners should record the name and telephone number of their Service Center. Your After Each Use:... -
Page 23: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1051 Warning: Hearing Protection Label... - Page 25 P P P PECO PECO PECO PECO PECO 10 WALDEN DRIVE ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...