Table of Contents
Advertisement
Quick Links
P
P P P
P
PECO
PECO
PECO
PECO
PECO
DESIGNED TO FIT:
900 SERIES BRIGGS & STRATTON
OPERATOR'S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0431
MODEL #: 37131504
PTO DRIVE
MODEL #: 37131505
MODEL #: 37131506
6.5HP BRIGGS & STRATTON
VANGUARD
PTO GRASS
COLLECTION
SYSTEM
2012 MODEL YEAR
TIGER CAT
52" & 61" VELOCITY
PLUS DECK
Advertisement
Table of Contents
Related Manuals for Peco 37131504
Summary of Contents for Peco 37131504
- Page 1 PECO COLLECTION SYSTEM DESIGNED TO FIT: 2012 MODEL YEAR TIGER CAT 52” & 61” VELOCITY PLUS DECK MODEL #: 37131504 PTO DRIVE MODEL #: 37131505 900 SERIES BRIGGS & STRATTON MODEL #: 37131506 6.5HP BRIGGS & STRATTON VANGUARD OPERATOR’S MANUAL...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Installation For Use
Section II - INSTALLATION FOR USE 2-1 Preparation Of Mower Remove the rear shield and skid plate from the mower. Figure 2-1c Remove (3) 3/8” carriage bolts and (3) 3/8”-16 nuts from the rear bumper to disconnect the rear shield. Remove Electric (2) 3/8”-16 carriage bolts (2) 3/8”-16 nuts from the skid Engine Pulley... -
Page 7: Lower Mount Tube Installation
2-3 Lower Mount Tube Installation 2-5 Top Assembly To Upper Frame Assembly Installation Secure (2) lower mount tubes P#(B0726) to the lower Position the top assembly P#(A1157) above the upper mount plate using (2) 5/16”-18 x 2” x 2-1/4” u-bolts frame assembly as shown in Figure 2-5. -
Page 8: Exhaust Diverter Installation
On all engine models with an engine oil drain hose on 2-7 Exhaust Diverter Installation the right side of the engine, attach the existing J-hook to the rear bumper using the PTO mount assembly Insert the exhaust deflector P#(J0251) onto the end of hardware shown in Figure 2-8b. -
Page 9: Belt Installation And Adjustment
Connect the belt A58K P#(M0236) from the engine 2-10 Belt Installation and Adjustment pulley to the lower gear box pulley (Figure 2-10d). PTO MODELS ONLY Figure 2-10d Loosen the (4) bolts P#(K1191), (2) on each side, that Connect Belt secure the gear box assembly to the PTO assembly To Both Pulleys P#(A0623) (Figure 2-10a and 2-10b). -
Page 10: Pto Handle Assembly Installation
2-11 PTO Handle Assembly 2-13 Outer Engine Mount Tube Installation Installation PTO MODELS ONLY Position the outer engine mount tube P#(B2220) as Attach the PTO handle P#(A1142) to the PTO assembly shown in Figure 2-13. Secure the outer engine mount using (3) 1/4”-20 x 3/4”... -
Page 11: Engine/Blower/Blade Assembly Installation
2-15 Engine/Blower/Blade Assembly 2-17 Inlet Installation Installation Slide the inlet P#(V0025) into the hole on the bagger top until the inlet locks into place. The inlet should pivot 360 Place the engine blower blade assembly on top of the degrees about the hole in the bagger top. Refer to engine mount arm as shown in Figure 2-15a. -
Page 12: Length Of Hose Adjustment
2-19 Length Of Hose Adjustment 2-21 Lower Hose To Blower Cone Installation The hoses in steps 2-20 and 2-21 must be cut to fit your machine. Follow steps 2-20 and 2-21. do not cut the Slide a 8”hose clamp P#(J0080) over both ends of the hoses until you have tried to fit them on your machine. -
Page 13: Impeller Blade Removal/Replacement
2-23 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the blower cone (#2) from the blower housing, located on 1 - Try carefully hitting the base of the impeller blade (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 14: Weight Kit Installation
2-24 Weight Kit Installation The collection system requires that a weight kit is After the weight brackets have been secured to the installed to the front of the mower to counter-balance the caster supports, place (1) weight bar P#(B0035) onto the weight of the collection system, when filled with debris. -
Page 15: Installation/Removal Of Collection Bags
2-25 Installation/Removal Of Figure 2-25c Collection Bags Plastic Top IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure 2-25a, on each bag ring before installing bags. Figure 2-25a Bag Ring Red Plastic End Caps Fasten Draw -Latch Here &... -
Page 16: Throttle Cable Installation
2-26 Throttle Cable Installation NOTE: Engine Driven Models Only Figure 2-26c To install the throttle cable kit to the ROPS (roll over protection system), place the 3/8” U-Bolt P#(K0136) onto the ROPS with the threads facing the front of the mower. -
Page 17: Exploded Part Views And Assemblies
Exploded Parts View A1157 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"... - Page 18 Exploded Parts View A0623 PTO Assembly ISO VIEW M0241 A50K BELT (INCLUDED IN H.W. BAG)
- Page 19 PTO Parts List A0623 PTO Assembly Item Document Title Quantity Number Number A0429 GEAR BOX ASSEMBLY K0348 3/8"-16 x 2" ALL THREAD HHCS K0047 3/8" FLAT WASHER 1.00 OD x .446 ID x .075 T K0353 1/4"-20 x 1/2" HHSTS K1159 5/16"-18 x 2"...
-
Page 23: Operating Instructions
3-3 Disengagement Of The Blower SECTION III PTO MODELS OPERATING A. To disengage the blower, rotate the engagement handle towards the mower. INSTRUCTIONS WARNING: The blower will continue to spin. DO NOT 3-1 General Safety TOUCH the blower, pulleys, or the belt until the tractor is turned off. -
Page 24: Lubrication
1. Clean all debris from machine especially from the container, underneath the belt shields, and safety decals. Replace any missing or illegible decals. PECO collection system owners should record the name and telephone number of their Service Center. Your 2. Inspect the unit for worn or damaged components. -
Page 25: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1051 Warning: Hearing Protection Label... - Page 27 P P P PECO PECO PECO PECO PECO 10 WALDEN DRIVE ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...