Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco 23131504
Summary of Contents for Peco 23131504
- Page 1 P P P GRASS COLLECTION PECO PECO PECO PECO PECO SYSTEM DESIGNED FOR: BOB-CAT PROCAT and predator pro F-SERIES & G-SERIES 2008-2012 MODEL 23131504 & 23131505 Pro Bagger Pro Bagger OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0421 $10.00 REV: 2...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
1-1 Introduction remove the right lower frame leg assembly. Another way We are pleased to have you as a PECO customer. Your to mark the holes is to use the full scale drill template to collection system has been designed to give you a low... -
Page 6: Lower Mount Assembly Installation
G-SERIES ONLY: Secure the oil cooler support to the F-Series: To mount the lower mount assembly left and right lower frame legs using existing hardware P#(A0672) to the rear of the mower, first remove the from the bumper removal. It may be necessary to loosen mower's (4) existing nuts and bolts. -
Page 7: Outer Engine Mount Tube Installation
2-5 Outer Engine Mount Tube 2-7 Engine/Blower/Blade Assembly Installation Installation Position the outer engine mount tube P#(B1117) as Position the engine/blower/blade assembly on top of the shown in Figure 2-5. Secure the outer engine mount engine mount arm assembly and secure with (4) 5-16”- tube to the lower mount assembly using (2) 3/8”-16 u- 18 x 1-1/2”... -
Page 8: Upper Frame Assembly Installation
2-8 Upper Frame Assembly 2-9 Top Assembly To Upper Frame Installation Assembly Installation & Inlet Installation Lift the upper frame assembly P#(A1838) into position above the lower mount assembly. Insert the vertical tube Position the top assembly P#(A1157) above the upper on the lower mount assembly into the vertical tube on frame assembly as shown in Figure 2-9. -
Page 9: Hing Kit Installation
2-10 Hinge Kit Assembly Installation 2-12 Blower Cone Installation Assemble the hinge kit as shown in Figure 2-10, using Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 1” HHCS P#(K1154), (3) 5/16”-18 nylon (2) 5/16”-18 x 2-1/2” HHCS P#(K0125) as shown in flange locknuts P#(K2516), (5) 1/4”... -
Page 10: Front Weight Assembly Installation
2-13 Front Weight Assembly Installation NOTE: A floor jack should be used to help position Position the weight P#(B0026) under the weight brackets and secure with (1)1/2”-13 x 4-1/4” x 4-5/16” U-bolt weights onto the brackets. When installing the weights P#(K0331), (2) 1/2”... -
Page 11: Length Of Hose Adjustment
2-14 Length Of Hose Adjustment 2-16 Lower Hose To Blower Cone Installation The hoses in steps 2-15 and 2-16 must be cut to fit your machine. Follow steps 2-15 and 2-16. Do not cut the Slide a 8” hose clamp P#(J0080) over both ends of the hoses until you have tried to fit them on your machine. -
Page 12: Throttle Cable Installation
2-18 Throttle Cable Installation To install the throttle cable kit to the ROPS (roll over protection system), place the 3/8” U-Bolt P#(K0136) Figure 2-18c onto the ROPS with the threads facing the front of the mower. Next slide on the throttle mount plate assembly P#(A0666) with the rivets also facing toward the front of the mower. -
Page 13: Installation And Removal Of Collection Bags
2-19 Installation/Removal Of Figure 2-19c Collection Bags Plastic Top IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure 2-19a, on each bag ring before installing bags. Figure 2-19a Bag Ring Red Plastic End Caps Fasten Draw -Latch Here &... -
Page 14: Impeller Blade Removal/Repalcement
2-20 Impeller Blade Removal/Replacement Tips on removing impeller blade; To gain impeller blade (#1) access, first remove the blower cone (#2) from the blower housing, located on 1 - Try carefully hitting the base of the impeller blade (#1), between each vein (#12), with a rubber mallet to the PTO assembly P#(A1821), by removing two blower loosen the taper-lock bushing hold. -
Page 15: Exploded Views And Part Drawings
Exploded Parts View A1158 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"... -
Page 18: Operating Instructions
* Remember that horsepower requirements will vary with PECO parts. the mowing conditions such as type and height of turf grass, moisture content, amount of leaves, whether the After Each Use: terrain is flat or sloped, etc. -
Page 19: Parts And Service
If for any reason your Service Center is unable to service your collection system or supply replacement parts, contact PeCo and include the following information on the chart below. PECO... -
Page 20: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1057... -
Page 22: Drill Template
DRAWING IS FULL SCALE. MAY BE USED A S A T EMPLATE. 0.75" DRILL T EMPLATE FOR T HE BOB-CAT REAR CHASSIS... - Page 23 NOTES...
- Page 24 P P P PECO PECO PECO PECO PECO 10 WALDEN DRIVE ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...