Makita UR140D Instruction Manual
Cordless string trimmer
Hide thumbs
Also See for UR140D:
- Technical information (12 pages) ,
- Instruction manual (89 pages) ,
- Instruction manual (85 pages)
Related Manuals for Makita UR140D
Summary of Contents for Makita UR140D
- Page 1 INSTRUCTION MANUAL Cordless String Trimmer UR140D UR180D 012390 IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model UR140D UR180D No load speed 6,000 min 7,800 min Overall length 1,229 mm - 1,433 mm 1,229 mm - 1,433 mm Cutting diameter with nylon cutting head 260 mm 260 mm Net weight 2.9 kg 2.9 kg... -
Page 3: Important Safety Instructions
Save all warnings and EC Declaration of Conformity instructions for future reference. Makita Corporation responsible manufacturer declare that the following Makita Be familiar with the controls and proper use machine(s): of the equipment. Designation of Machine: Cutting elements continue to rotate after the Cordless String Trimmer motor is switched off. - Page 4 Do not open or mutilate the battery(ies). Intended use of the tool Released electrolyte is corrosive and may Use right tool. The cordless string trimmer is cause damage to the eyes or skin. It may be only intended for cutting grass, light weeds. It toxic if swallowed.
- Page 5 Method of operation Maintenance instructions Never operate the machine with damaged The condition of the cutting tool, protective guards or without the guards in place. devices must be checked before commencing Only use the tool in good light and visibility. work.
- Page 6 Do not short the battery cartridge: Do not touch the terminals with any conductive material. Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
-
Page 7: Parts Description
PARTS DESCRIPTION Indication lamp Clamping nut Switch trigger Lock grip Battery cartridge Guard Front grip Nylon cutting head 013641... -
Page 8: Functional Description
Overloaded: • FUNCTIONAL DESCRIPTION The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on WARNING: the tool and stop the application that caused Always be sure that the tool is switched off •... - Page 9 Indication lamp 1. Indication lamp 012441 Running the tool allows the indication lamp to show the battery cartridge capacity status. When the tool is also overloaded and has stopped during operation, the lamp lights up in red. Refer to the following table for the status and action to be taken for the indication lamp.
- Page 10 Put the front grip on the front grip holder and secure it Nylon cutting head with a hex bolt and the clamping nut provided with the NOTICE: string trimmer as shown in the figure. At this time, the The bump feed will not operate properly if the •...
- Page 11 1. Nylon cord 2. Retainer for nylon cord end 012408 012413 Insert a Nylon cord to the retainer shown in the figure. 012409 To remove the Nylon cutting head (spool and spool 012414 cover) from the string trimmer, press in the latches Wind it tightly flat around the spool in the direction of forcefully on both sides of the spool cover and raise it.
-
Page 12: Operation
1. Spool 2. Nylon cord 012417 012400 After installing the Nylon cutting head, make sure that CAUTION: the Nylon cord comes out by pressing the spool and Use the trimmer without getting the spool into • pulling the Nylon cord. a contact with the ground surface. - Page 13 Hold the trimmer tilting at a level so that it does not motor housing 180 and tighten the grip clockwise until contact the ground surface and cut the grass using the it locks. Nylon cord tip like knocking the ground. In this work, NOTE: smooth feeding out is needed because the Nylon cord wears more quickly than usual.
-
Page 14: Maintenance
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Nylon cutting head • Nylon cords • Shoulder strap •... - Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 885086C229...