Table of Contents
Advertisement
74
TPE1.1U LA
Item
1920X1080i
60Hz
Pixel rate
74.25MHz
(13.468 ns)
Horizontal
33.75KHz
Frequency
Active
1920 pixels
(25.859 us)
Blank
280 pixels
(3.771 us)
Period
2200 pixels
(29.630 us)
Pulse
44 pixels
delay
(0.593 us)
Pulse
44 pixels
width
(0.593 us)
Vertical
60 Hz
Frequency
Active
1080 lines
(32.000 ms)
Blank
45 lines
(1.333 ms)
Period
1125 lines
(33.333 ms)
Pulse
2 lines
delay
(0.059 ms)
Pulse
5 lines
width
(0.148 ms)
EQ before
0 line
EQ after
1 line
Scan
Interlace
Sync type
ACS
Video kind
Analog
YPbPr (ITU-
R BT.709)
2.5.1 HDMI Timing
(For Quantum Data setting with Q802BT in HDMI mode.)
Item
1920X1080i
60Hz
Pixel rate
74.25MHz
(13.468 ns)
Horizontal
33.75KHz
Frequency
Active
1920 pixels
(25.859 us)
Blank
280 pixels
(3.771 us)
Period
2200 pixels
(29.630 us)
Pulse delay
88 pixels
(1.186us)
Pulse width
44 pixels
(0.593 us)
Vertical
60 Hz
Frequency
Active
1080 lines
(32.000 ms)
Blank
45 lines
(1.333 ms)
Period
1125 lines
(33.333 ms)
Pulse delay
2 lines
(0.059 ms)
Pulse width
5 lines
(0.148 ms)
EQ before
0 line
EQ after
1 line
Scan
Interlace
Sync type
ACS
Video kind
Analog YPbPr
(ITU-R BT.709)
1280X720P
720X480P
60Hz
60Hz
74.25MHz
27.027MHz
(13.468 ns)
(37.000 ns)
45KHz
31.5KHz
1280 pixels
720 pixels
(17.239 us)
(26.640 us)
370 pixels
138 pixels
(4.983 us)
(5.106 us)
1650 pixels
858 pixels
(22.222 us)
(31.746 us)
70 pixels
16 pixels
(0.943 us)
(0.592 us)
40 pixels
62 pixels
(0.539 us)
(2.294 us)
60 Hz
60 Hz
720 lines
480 lines
(16.0 ms)
(15.238 ms)
30 lines
45 lines
(0.667 ms)
(1.429 ms)
750 lines
525 lines
(16.667 ms)
(16.667 ms)
5 lines
9 lines
(0.111 ms )
(0.287 ms)
5 lines
6 lines
(0.111 ms)
(0.190 ms)
0 line
0 line
0 line
0 line
Progressive
Progressive
ACS
ACS
Analog
Analog
YPbPr (ITU-
YPbPr
R BT.709)
(SMPTE
RP177)
1280X720P
720X480P
60Hz
60Hz
74.25MHz
27.027MHz
(13.468 ns)
(37.000 ns)
45KHz
31.5KHz
1280 pixels
720 pixels
(17.239 us)
(26.640 us)
370 pixels
138 pixels
(4.983 us)
(5.106 us)
1650 pixels
858 pixels
(22.222 us)
(31.746 us)
110 pixels
16 pixels
(1.482us)
(0.592 us)
40 pixels
62 pixels
(0.539 us)
(2.294 us)
60 Hz
60 Hz
720 lines
480 lines
(16.0 ms)
(15.238 ms)
30 lines
45 lines
(0.667 ms)
(1.429 ms)
750 lines
525 lines
(16.667 ms)
(16.667 ms)
5 lines
9 lines
(0.111 ms )
(0.287 ms)
5 lines
6 lines
(0.111 ms)
(0.190 ms)
0 line
0 line
0 line
0 line
Progressive
Progressive
ACS
ACS
Analog YPbPr
Analog YPbPr
(ITU-R BT.709)
(SMPTE RP177)
8. Alignments
3.
Power supply
720X480i
60Hz
3.1
Setup the AC Input at 110VAC, and power board provide two DC
13.5MHz
Output
( 74.074 ns )
1. The DC output voltage is 24V ± 0.5V DC for Inverter and Scalar
15.734KHz
board . Measure between pin3 (F026, +24V) and pin7 (F030,
720 pixels
GND) at item 1089 of power board with 0.1A load. Measure
(53.333 us)
between pin1 (F034, +24V) and pin8 (F039, GND) at item 1088
138 pixels
of power board with 4A load.
( 10.222 us )
2. The DC output voltage is 16V ± 1 V DC for Scalar and Audio
858 pixels
board. Measure between pin2 (F025, +16V) and pin7 (F030,
( 63.556 us )
GND) at item 1089 of power board with 2A load.
19 pixels
3. The DC voltage is 400V +/- 10V in power board. Measure
( 1.407 us )
between test point F004 and ground pin of item 2060 (120uF,
62 pixels
450V) of power board.
( 4.593 us )
59.94 Hz
3.2
No adjustment is needed.
480 lines
( 30.507
4.
IF PLL Offset Adjustment
ms )
45 lines
A)
EQUIPMENT SETUP :
(2.860 ms )
525 lines
B)
INPUT REQUIREMENTS
( 33.367
ms )
4.1
Input signal
4 lines
4.2
Input injection point : Tuner input.
( 0.254 ms )
3 lines
C)
ALIGNMENT METHOD
(0.191 ms )
3 line
4.3
Alignment set-up: video pattern = crosshatch, sound = BTSC
3 line
stereo mode, without audio modulation, picture/sound
Interlace
ratio=7dB,and at SAM mode.
ACS
Analog
4.4 Method of Alignment
YPbPr
(SMPTE
4.4.1 Set audio volume Loudspeakers to max : (+12dB avip setting)
RP177 )
4.4.2 Via IIC, adjust the 'PLL offset' register (address 9E, sub-address 02,
bit D5 to D0) value to get the lowest noise at audio output (I905).
4.4.3 NVM FactAlignMainIfPLLOffsetNeg at sub-address
006Chex, 1037hex, 1630hex.
5. TV Mode display adjustment
5.1 White balance adjustment (B)
5.1.1 General set-up :
Equipment Requirements: Color analyzer.
Input requirements:
Input Signal Type : RF signal
1. Set to NTSC system, frequency=187.25MHZ ( for NAFTA
model ), with white pattern of 100%
2. Select Smart picture to Personal mode and check the x, y data.
Input Signal Strength : 10mV (80 dBuV) terminal voltage.
Input Injection Point : TV Tuner input
Alignment method:
Initial Set-up :
1.Set Smart picture as "Personal" and to be Contrast =92
(32"LPL)/92(26"QDI), Brightness=63(32"LPL)/85(26"QDI),
at normal menu mode.
2. Apply "100% Full White" pattern by TV pattern generator.
3. Entry SAM menu: press Numeric keys 062596+ info key.
Alignment
for "NORMAL","WARM" and "COOL" color temperatures.
1. Check (X, Y) co-ordinates as below:
Picture Mode
Normal
WARM
COOL
Table 3: Reading with Minolta CA-110.
Fluke 54200
: M-NTSC, RF(203.25MHz, 70dBuV)
:
: Adjust the RGB White point in Factory Mode
X
0.295±0.005
0.285±0.005
0.315±0.005
0.310±0.005
0.275±0.005
0.260±0.005
y
Advertisement
Table of Contents
