Table of Contents
Advertisement
19" / 1U - C-Charger High Voltage Power Supplies
1
Safety instructions ........................................................................................................................ 3
2
Technical data .............................................................................................................................. 4
2.1
General technical data............................................................................................................ 6
3
Functional description ................................................................................................................... 7
3.1
Operation states ..................................................................................................................... 8
3.2
Safety loop (Interlock) ............................................................................................................ 8
Operating see the attachment point 4 to 7
!
Attention!
The unit must not be operated with the cover removed
-
to avoid the possibility of lethal shock to the operator!
We decline all responsibility for damages and injuries caused by an improper use of the
-
module. It is strongly recommended to read the operator's manual before operation!
Note
All information in this document is subject to change without notice. We take no responsibility for any
error in this document. We reserve the right to make changes in the product design without any noti-
fication to the users.
Filename HPx-LPx_300-800W_HW01_eng.___; Version 5.19 as of 2009-07-15
iseg Spezialelektronik GmbH
Bautzner Landstr. 23
D - 01454 Radeberg / Rossendorf
19" / 1U - High Voltage Power Supplies
HPS 300 W and 800 W series
LPS 300 W and 800 W series
Operator's manual
Email: sales@iseg-hv.de
http://www.iseg-hv.de
S p e z i a l e l e k t r o n i k G m b H
Tel
++ 49 (0)351 / 26 996 - 0
Fax
++ 49 (0)351 / 26 996 - 21
Advertisement
Table of Contents
Related Manuals for iseg HPS 300 W series
Summary of Contents for iseg HPS 300 W series
-
Page 1: Table Of Contents
We reserve the right to make changes in the product design without any noti- fication to the users. Filename HPx-LPx_300-800W_HW01_eng.___; Version 5.19 as of 2009-07-15 iseg Spezialelektronik GmbH Email: sales@iseg-hv.de ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. - Page 2 S p e z i a l e l e k t r o n i k G m b H iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0)351 / 26 996 - 21...
-
Page 3: Safety Instructions
(> 15 s) of the output capacitance has to be kept and the discharge status has to be checked afterwards. Only skilled and authorised people are allowed to do any service, repair or maintenance for this unit. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. -
Page 4: Technical Data
Lmin in the output voltage range: 1% • V ≤ V ≤ V iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0)351 / 26 996 - 21... - Page 5 ≤ R < no load and ∆V Lmin in the output voltage range: 5 V ≤ V ≤ V iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
-
Page 6: General Technical Data
5 up to 35 ° C Humidity: 30% up to 80 %, no condensation Storage temperature 0 up to 60 ° C iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de... -
Page 7: Functional Description
If the potential between “0 V“ and “⊥ ⊥ ⊥ ⊥ /PE“ connector is > 300V then – in order to avoid damages for the unit – the connections are short circuited with help of internal electronically protection circuits. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. -
Page 8: Operation States
If chosen AIF ON in the menu F06 „Control with analogue I/O automatically“ it is able to switch on high voltage with Low to High on the INHIBIT pin of the analogue I/O too. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. -
Page 9: Front Panel Operation
After turning high voltage off, the displays show the measured values while ramping down. After four seconds an with measured voltage lower than 60 V, the device shows the set values again. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. - Page 10 Select IEEE address with rotary encoder VOLTAGE: 01 to 30. Factory setting is 17. F10 Addr CAN Select CAN address with rotary encoder VOLTAGE: 00 to 63. Factory setting is 0. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
-
Page 11: Software Limits
ESFLPngd SAFETYLOOP Safety loop was or is open ETEMPngd OVERTEMPATURE Maximum allowed temperature was or is exceeded iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21... - Page 12 CAN-Interface Multi-Channel High Voltage Power Supply Module EHS xxx and EDS xxx Thus, the device can be controlled with the program isegCANHVControl or with the iseg OPC server. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 13 13 10). On input side, no leading zeros are needed. Output is fixed format without leading zero. A minimum time delay of 20 ms between write and read instructions is needed. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr.
- Page 14 Please choose “No, not this time” in the first dialog and then click Next. 4. Choose “Install from a list or specific location” in the next dialog and then click Next: iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 15 It may be necessary to do the steps 3 to 6 again, before the device can be used (the first time, a bus driver is installed, the second time, the virtual COM port driver is installed). iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr.
- Page 16 Accessories Communications HyperTerminal Create a new connection with menu „File New Connection“, name it e. g. “HPS” and click OK. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0)351 / 26 996 - 21...
- Page 17 The following dialog appears. Choose your serial port and click OK: Please enter the interface parameters in the following dialog: After clicking OK, the interface setup is finished. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr.
- Page 18 ASCII Setup the setting “Send line ends with line feeds” has to be made (see following picture). You can now test the communication with the device: iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 19 On input side, no leading zeros are needed. Output is fixed format without leading zero. A minimum time delay of 5 ms between two IEEE commands is needed. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr.
-
Page 20: Ethernet Interface
SYN, ACK send() "*IDN?\r\n" recv() "iseg Spezialelektronik GmbH [...]" closesocket() FIN, ACK FIN, ACK The first three packages are for the establishing of a TCP-Connection (three way handshake). Fourth step is the inquiry from PC to HV unit. The order is ASCII coded in data field of the TCP packet. The answer is also ASCII coded send to the PC in step 5. - Page 21 WSACleanup(); // print answer to screen printf("%s\n", ans); return 0; iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 22 “OFF” automatically. If you will use „Auto AIF“ again, you must choose “AIF” in the menu „F07 Set Interfce“ before and than set the automatic function “Auto AIF” in the menu „F06 Auto AIF“ to “ON”. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 23 Example: HPp 40 357, maximum output current = 350 mA Output current (mA) I-MON corresponds to corresponds to corresponds to iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 24 This is the recommended command Set. To use this command set, choose “EDCP” in the menu or the *INSTR command. (EDCP = Enhanced Device Communication Protocol). This command set is oriented on the iseg EDCP CAN Protocol with Status and Event handling.
- Page 25 :EVent Query Channel Event Status Word :STATus? Query Channel Event Status Mask :MASK? iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 26 10 A ≤ I < 100 A 12.3456A Examples: Read Module Identification: *IDN? iseg Spezialelektronik GmbH,HPp 40 207,680001,5.24 Set Voltage to 1000.501 V :VOLT 1000.501 Set Current to 1.58 mA :CURR 0.00158 Set Voltage Ramp speed to 300 Volt per second...
- Page 27 No Ramp is running isIERR InputError Input error No Input error Reserved iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 28 If one of the EventStatus Bits EVLIM, ECLIM, ETRIP, EEINH, EVBNDs, ECBNDs, EEMCY is set, it prevents turning on the High Voltage again until the corresponding bit is cleared. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 29 IsFineAdjustment Adjustment is on Adjustment is off Reserved iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 30 Event: A hardware failure of the HV module has been detected. The HV is ESrvs EventService switched off without the possibility to switch on again. Please consult the iseg Spezialelektronik GmbH. Reserved iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr.
- Page 31 STATUS,IL IL, RANGE=100.0mA, VALUE=30.0mA Read out the voltage ramp speed: STATUS,RAMP RAMP, RANGE=3000V/s, VALUE=1000V/s iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 32 LAM,INPUT ERROR Wrong command received Status OK LAM,OK Read out the device identification ID, iseg Spezialelektronik r5.01 sn.680041 Typ HPn 30 107 iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0)351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de...
- Page 33 :READ:LIMIT:CURRent? IL, RANGE=100.0mA, VALUE=30.0mA Command to read out the voltage ramp speed: :READ:RAMP? Ramp, RANGE=3000V/s, VALUE=3000V/s iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr. 23 http://www.iseg-hv.de Fax ++ 49 (0) 351 / 26 996 - 21...
- Page 34 For LAM status description, see chapter 6.1, LAM status. Read out the device identification :READ:IDNT? ID, iseg Spezialelektronik r5.01 sn.680042 Typ HPn 30 107 Common command set (Compatibility to old HPS) The Common commands can be used all the time, independently from selected instruction set (ET or SCPI).
-
Page 35: Troubleshooting
If these provisions do not lead to a good result, this unit has to be checked from an authorised agent or must be shipped to the factory. iseg Spezialelektronik GmbH Email: sales@iseg-hv.de Tel ++ 49 (0) 351 / 26 996 - 0 Bautzner Landstr.
Need help?
Do you have a question about the HPS 300 W series and is the answer not in the manual?
Questions and answers