Enjoying Music In The Remote Zone; Using The Buttons On The Tx-Sr800; Using The Remote Controller; Adjusting The Volume For The Remote Zone - Onkyo TX-SR800 Instruction Manual

Enjoying music in the remote zone

ZONE 2 indicator
DISPLAY
STANDBY/ON
STANDBY
POWER
ON OFF
DIRECT / PURE AUDIO STEREO
PURE AUDIO UPSAMPLING
ZONE 2 GRN ( )
PHONES
REC ( RED )
AUDIO DVD VIDEO 1
SELECTOR
VCR 1

Using the buttons on the TX-SR800

1. Press the ZONE 2 button on the TX-SR800.
2. Select an input source.
After pressing the ZONE 2 button, you must press an input
source button within 8 seconds.
The indicator above the input source button lights green. In this
condition, even if you change the input source for the main zone,
the input source for the remote zone (Zone 2) will not change.
Ex.: When the CD button is pressed.
To select the same source for the remote zone that is selected
for the main zone, press the ZONE 2 button again until "Z2
Sel:SOURCE" appears in the display.
In this condition, if you change the input source for the main zone,
the input source for the remote zone (Zone 2) will change as well.
When "Z2 Sel:Off" is displayed, the output to the remote
zone is turned off.
Notes:
• If a sleep time is set with the SLEEP button, the output to the
remote zone will also turn off when the sleep time elapses.
• The ZONE 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source, check
if the component is connected to the analog inputs.
• If the REC OUT button is pressed in the main room while someone
is using the system in the remote zone, the Zone 2 function will be
deactivated and the source will turn off in the remote zone.
• If you select FM (or AM) with the TUNER input source buttons
when the source for the remote zone (Zone 2) is set to AM (or
FM), the output for the remote zone also changes to AM (or
FM).
• 7.1-channel playback in the main room is disabled if the Surr
Back/Zone 2 setting in the Surr Back/Zone 2 sub-menu of the
Hardware Setup Menu is set to "Zone 2."
• When you are using the remote zone (Zone 2),
operation will not work.
• When you are using the remote zone (Zone 2), the Pure Audio
setting will not work.
• When you are not using the remote zone (Zone 2), press the
OFF button to turn off the ZONE 2 indicator. (Using the
remote controller, press the ZONE 2 button and then the
STANDBY button.)
36
OFF
ZONE 2
DIMMER REC OUT ZONE 2 OFF
SETUP
TUNING
ENTER
RE TURN
PRESET
SURROUND THX DSP MEMORY FM MODE A-FO RM LISTENING MODE MEMORY
CLEAR
VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 TAPE TUNER PHONO C D
VCR 2
DIGITAL S VIDEO
Input source buttons
SLEEP
MASTER VOLUME
VIDEO 5 INPUT
VIDEO L AUDIO R
TX-SR800

Using the remote controller

After pressing the ZONE 2 button, press the ON/STANDBY
button within 5 seconds.
Select an input source:
After pressing the ZONE 2 button, press an INPUT SELECTOR
button within 8 seconds.
If tuner is selected with the TUN button, you can use the CH
button to select a preset radio station.
Note:
After you press the ZONE 2 button on the remote controller, the
STANDBY indicator on the TX-SR800 flashes for five seconds.
During this time, you will not be able to perform operations in the
main zone using the remote controller.

Adjusting the volume for the remote zone

When the remote zone (Zone 2) speakers are connected to the SURR
BACK/ZONE 2 SPEAKERS terminals, or to an amplifier connected
to the SURR BACK/ZONE 2 PRE OUT terminals, adjust the
volume as shown below.
Using the remote controller:
After pressing the ZONE 2 button, the STANDBY indicator on the
TX-SR800 will flash for 5 seconds. During this time press the
LEVEL / button.
system
ON/STANDBY
LEVEL /
INPUT SELECTOR
buttons
ZONE 2