Download Print this page

Advertisement

Operating and installation instructions
Gas wok burner
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
en-GB
M.-Nr. 07 172 900

Advertisement

   Related Manuals for Miele CS 1011

No related manuals

   Summary of Contents for Miele CS 1011

  • Page 1

    Operating and installation instructions Gas wok burner To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 07 172 900...

  • Page 2

    It is, however, set up for connection to the gas and electricity supplies in the countries specified. For trouble-free operation of the appliance, it is best to use it in the countries specified for use. For use in other countries, please contact Miele in your country.

  • Page 3

    Gas-heated appliances Safety precautions to take if you smell gas  Turn off the gas emergency control valve immediately. This is usually located near the gas meter.  Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ...

  • Page 4: Table Of Contents

    Contents Warning and Safety instructions................ 6 Caring for the environment ................ 16 Guide to the appliance .................. 17 Wok ........................17 CS 1011...................... 17 CS 1021...................... 18 Indicators....................... 19 Burner........................20 Accessories supplied .................... 21 Using for the first time .................. 22 Cleaning the CombiSet for the first time ...............

  • Page 5

    Contents Safety distances .................... 37 Installation notes .................... 40 Building-in dimensions .................. 41 CS 1011......................... 41 CS 1021......................... 42 Building-in several CombiSets ................ 43 Installation...................... 45 Electrical connection .................. 49 Gas connection.................... 51 Burner ratings ......................  53 Converting to another gas type .................  54 Jet table.........................

  • Page 6: Warning And Safety Instructions

    They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep these instructions in a safe place and ensure that new users...

  • Page 7

    Warning and Safety instructions Correct application  This wok is designed for domestic use and for use in similar envir- onments.  This wok is not intended for outdoor use.  This wok is intended for domestic use only to cook food and keep it warm.

  • Page 8

    Warning and Safety instructions Safety with children  Children under 8 years of age must be kept away from the wok unless they are constantly supervised.  Children 8 years and older may only use the wok unsupervised if they have been shown how to use it safely and recognise and under- stand the consequences of incorrect operation.

  • Page 9

    Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and re- pairs must only be carried out by a Miele authorised technician.  A damaged wok can be dangerous. Check it for visible signs of damage.

  • Page 10

    Miele authorised service technician. Otherwise the guar- antee is invalidated.  Miele can only guarantee the safety of the appliance when genu- ine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.

  • Page 11

    Do not use the hob if it is faulty. Switch it off immediately, discon- nect it from the mains electricity supply and the gas supply and con- tact Miele.  If the wok is installed behind a furniture panel (e.g. a door), ensure that the door is never closed whilst the wok is in use.

  • Page 12

    Warning and Safety instructions Correct use  The wok gets hot when in use and remains hot for some time after being switched off. The risk of burning is present until the residual heat indicators have gone out.  Do not use the wok to heat up the room. Due to the high temperatures radiated, objects left near the wok could catch fire.

  • Page 13

    If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or sur- rounding units and also parts of the cooktop. Miele cannot be held li- able for this type of damage.

  • Page 14

    Warning and Safety instructions  The pan support supplied with the appliance must always be used. Never place a pan on the burner itself.  Replace the pan supports carefully to avoid scratching the surface of the hob.  Do not use or store flammable materials near this appliance. ...

  • Page 15

    Warning and Safety instructions Cleaning and care  Do not use a steam cleaning appliance to clean this wok. The steam could reach electrical components and cause a short cir- cuit.

  • Page 16: Caring For The Environment

    / recycling centre for electrical and electronic ap- pliances, or contact your dealer or Miele for advice. You are also respons- ible by law for deleting any personal data that may be stored on the appli- ance being disposed of. Please ensure...

  • Page 17: Guide To The Appliance

    Guide to the appliance CS 1011 a Wok burner c Control knob b Pan support d Indicators...

  • Page 18

    Guide to the appliance CS 1021 a Wok burner c Control knob b Pan support d Indicators...

  • Page 19: Indicators

    Guide to the appliance Indicators e In-operation indicator f Residual heat indicator Control knob Symbol Description  Burner off, the gas supply is turned off  Largest flame: inner and outer burner on highest setting.  Large flame: outer burner on lowest setting, inner burner on highest setting. ...

  • Page 20: Burner

    Guide to the appliance Burner g Inner burner cap h Outer burner cap i Burner ring j Burner head k Thermocouple with ignition safety device l Ignitor m Burner base...

  • Page 21: Accessories Supplied

    Guide to the appliance Accessories supplied The accessories supplied with your ap- pliance as well as a range of optional ones are available to order from Miele (see "Optional accessories"). Wok ring The wok ring supplied gives additional stability to the wok, especially to woks with a rounded base.

  • Page 22: Using For The First Time

    Using for the first time  Please stick the extra data plate for Switching on the CombiSet for the appliance supplied with this doc- the first time umentation in the space provided in The metal components have a protect- the "After sales service, data plate, ive coating which when heated for the guarantee"...

  • Page 23: Pans

    Miele cannot be held liable for this type of damage. – Remember when purchasing new pans that manufacturers usually refer...

  • Page 24: Wok Ring

    Pans Wok ring  Use the wok ring supplied to give ad- ditional stability to the wok, especially to woks with a rounded base.  Make sure that the wok ring is loc- ated securely in its correct position. See illustration. The wok is unique among cookware in that it has a small base diameter and a large rim diameter (usually 35-40 cm).

  • Page 25: Tips On Saving Energy

    Tips on saving energy – Use a pan lid whenever possible to minimize heat loss. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. – Cook with as little water as possible. – Reduce the size of the flame once the water has come to the boil or the oil is hot enough to fry in.

  • Page 26: Operation

    Operation Rapid ignition system Switching on The appliance is supplied with a rapid  Fire hazard. ignition system with the following fea- Do not leave the appliance unatten- tures: ded whilst it is being used. – Rapid ignition without pressing and ...

  • Page 27: Adjusting The Flame

    Operation Adjusting the flame Switching off  Turn the control clockwise to position As the outer part of the flame is much "". hotter than the centre, the tips of the flames should stay beneath the pan This stops the flow of gas and the flame base.

  • Page 28: Safety Features

    Safety features Flame failure monitor Safety switch-off This wok has a thermo-electric flame If the burner has been used for an un- failure monitor. If the flame goes out, for usually long period of time, it will switch example because food has boiled over itself off automatically.

  • Page 29: Cleaning And Care

    Cleaning and care  Allow the CombiSet to cool down Danger of burning. before cleaning. The appliance must be switched off and have cooled down before clean-  The CombiSet and accessories ing. should be cleaned after each use.  Dry the CombiSet after using water to ...

  • Page 30: Stainless Steel Frame/control Panel

     Finally, dry with a clean soft cloth. Operating controls Tip: The Miele conditioning agent for stainless steel can be used after clean-  Clean the control(s) with a solution of ing to help keep your appliance looking warm water and a little washing-up li- good (see "Optional accessories").

  • Page 31: Pan Supports

    Cleaning and care Pan supports Burner Do not clean the pan supports in a Do not clean any parts of the burner dishwasher. in a dishwasher.  Remove the pan supports.  The burner should be dismantled and then cleaned by hand using a solu- ...

  • Page 32: Assembling The Burner

    Cleaning and care Assembling the burner  Place the burner head  onto the burner base  so that the thermo- couple  and the ignitor  extend through their respective holes. The lobe  on the burner cap must fit into the recess  on the burner head.

  • Page 33: Problem Solving Guide

    Danger of injury. Installation, maintenance and repairs may only be carried out by a suitably qualified and competent person. Repairs and other work by unqualified persons could be dangerous. Miele can- not be held liable for unauthorised work. Do not attempt to open the casing of the CombiSet yourself.

  • Page 34

    The ignitor on the The mains fuse has tripped. burner does not spark.  You may need to contact a qualified electrician or Miele. There is food residue stuck between the ignitor and the burner cap. There is food residue on the thermocouple.

  • Page 35: Optional Accessories

    Helps keep the appliance looking These products can be ordered through good for longer. the Miele Webshop. These can also be ordered from Miele (see end of this booklet for contact de- tails) or from your Miele dealer. Ceramic and stainless steel...

  • Page 36: Safety Instructions For Installation

    Safety instructions for installation Fit the wall units and cooker hood before fitting the CombiSet to avoid dam- aging it.  The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.

  • Page 37: Safety Distances

    Safety distances Safety distance above the CombiSet A minimum safety distance must be maintained between the CombiSet and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood a min- imum safety distance of at least 760 mm must be maintained, or if any flammable objects (e.g.

  • Page 38

    CS 1134 CS 1326 CS 1327 CS 1411 100 mm CS 1012 / CS 1012-1 150 mm CS 1421 CS 1312 Not recommended CS 1322 200 mm CS 1034 / CS 1034-1 250 mm CS 1011 / CS 1021 Not recommended...

  • Page 39

    Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance ...

  • Page 40: Installation Notes

    Installation notes Seal between the CombiSet Tiled worktop and the worktop Grout lines  and the hatched area un- derneath the CombiSet frame must be smooth and even. If they are not the Do not use sealant between the CombiSet will not sit flush with the CombiSet and the worktop.

  • Page 41: Building-in Dimensions

    Building-in dimensions CS 1011 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)

  • Page 42

    Building-in dimensions CS 1021 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)

  • Page 43: Building-in Several Combisets

    Building-in several CombiSets Example: 3 CombiSets a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips e CombiSet width minus 8 mm f CombiSet width g CombiSet width minus 8 mm h Worktop cut-out...

  • Page 44

    Building-in several CombiSets Calculating the worktop cut-out The frames of the CombiSets overlap the worktop at the outside right and left by 8 mm on each side.  Add up the widths of the CombiSets and subtract 16 mm from this figure. Example: 288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see...

  • Page 45: Installation

    Installation Preparing the worktop  Make the worktop cut-out as shown in "Building-in dimensions" or as cal- culated (see Building-in several CombiSets). Observe the safety dis- tances (see "Safety distances"). Wooden worktops  Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.

  • Page 46

    Installation Natural stone worktops You will need heavy duty double-side tape (not supplied) to secure the spring clamps and spacer bars.  Apply silicone to the side and lower edges of the spring clamps  and the spacer bars .  Then fill gap  between spacer bar ...

  • Page 47

    Installation Building in several CombiSets Installing the CombiSet  Push the built-in CombiSet to the  Feed the mains connection cable side until the holes in the spacer bar down through the cut-out. can be seen.  Starting at the front, position the CombiSet in the worktop cut-out.

  • Page 48

    Installation Connecting the CombiSet Removing the CombiSet  Connect the CombiSet to the electri-  If the CombiSet can be accessed city and gas supplies (see "Gas con- from below, push it out from below. nection"). Push the rear side out first. ...

  • Page 49: Electrical Connection

    Residual current device  Danger of injury. For extra safety, it is advisable to pro- Miele cannot be held liable for unau- tect the CombiSet with a suitable resid- thorised installation, maintenance ual current device (RCD) with a trip and repair work as this can be dan- range of 30 mA.

  • Page 50

    If the mains cable needs to be replaced it must be replaced with a special con- Safety fuses nection cable, type H 05 VV-F (PVC-in- sulated), available from Miele.  Completely remove fuses The connection data is quoted on the Automatic circuit breakers data plate.

  • Page 51: Gas Connection

    Gas connection  Any special local conditions relating Connection to the gas supply, or to gas installations as well as build- conversion to a different gas type, ing regulations must also be ob- may only be undertaken by an ap- served.

  • Page 52

    GB may be included with the hob. Please d 90° bend contact your supplier or Miele for the Connection with test point specific- appropriate conversion jets if neces- ally for GB and 90 ° bend.

  • Page 53: Burner Ratings

    Burner ratings Nominal ratings Gas type Highest setting Lowest setting Natural gas H – 0.26 Liquid gas 0.26...

  • Page 54: Converting To Another Gas Type

    Converting to another gas type Changing the jets  Conversion from one type of gas to another, should only be under-  Disconnect the hob from the electri- taken by an approved and registered city supply and turn off the gas sup- gas installer in strict accordance with ply.

  • Page 55

    Converting to another gas type To change the main jet  Carefully remove the upper section of the appliance. When doing this make sure you do not pull out the light unit  located underneath the upper  Unscrew the main jet anti-clockwise section.

  • Page 56

    Converting to another gas type To change the jet for the inner burner d Jet disc (main jet for the inner burner) e Air intake sleeve f Vent  Remove the screw  from the fit- ting  with an SW 8 spanner while counterholding it with an SW 12 spanner.

  • Page 57: Checking The First Intake Of Air

    Converting to another gas type Checking the first intake of air Changing the small jet a Adjustment screw b Air intake sleeve a Small diameter jet (e.g. for liquid gas: 0,23) Gap X must measure: For natural gas: 6 mm b Large diameter jet For liquid gas: 13 mm (e.g.

  • Page 58: Functional Check

    Converting to another gas type Functional check  Check all gas fittings for leaks.  Reassemble the hob.  Ignite all burners to check that they are operating correctly. – The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.

  • Page 59: After Sales Service, Data Plate, Guarantee

    N.B. A call-out charge will be applied to service visits where the problem could have been resolved as described in these instructions. When contacting your Dealer or Miele, please quote the model and serial number of your appliance. Data plate Space in which to stick the extra data plate supplied with the appliance.

  • Page 63

    Tel: +971 4 3044 999 Tel: (01) 461 07 10, Fax: (01) 461 07 97 Fax: +971 4 3418 852 E-Mail: info@miele.ie, Internet: www.miele.ie 800-MIELE (64353) Manufacturer: Miele & Cie. KG E-Mail: info@miele.ae Carl-Miele-Straße 29, 33332 Gütersloh, Germany Internet: www.miele.ae...

  • Page 64

    CS 1011 / CS 1021  en-GB M.-Nr. 07 172 900 / 13...

This manual also for:

Cs 1021

Comments to this Manuals

Symbols: 0
Latest comments: