Table of Contents
Advertisement
5
Place the setup microphone at the next position,
and then press ENTER.
Audyssey 2EQ
takes a few minutes.
6
When prompted, place the setup microphone at
the next position, and repeat step 5.
7
Use q/w to select an option, and then press
ENTER.
2EQ: Auto Setup
Save
Cancel
The options are:
Save:
Save the calculated settings and exit
Audyssey 2EQ Room Correction and Speaker
Setup.
Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
Note
• You can view the calculated settings for the speaker con-
figuration, speaker distances, and speaker levels by using
e/r.
8
Disconnect the speaker setup microphone.
Note
• When Audyssey 2EQ Room Correction and Speaker Setup is
complete, the "Audyssey" will be set to "On"
Audyssey indicator will light
• You can cancel Audyssey 2EQ Room Correction and Speaker
Setup at any point in this procedure simply by disconnecting the
setup microphone.
• Do not connect or disconnect any speakers during
Audyssey 2EQ Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey 2EQ Room Correction and Speaker Setup starts.
• Changes to the room after Audyssey 2EQ Room Correction and
Speaker Setup requires you run Audyssey 2EQ Room Correc-
tion and Speaker Setup again, as room EQ characteristics may
have changed.
En
24
®
performs more measurements. This
Audyssey
<- Review Speaker Configuration ->
Subwoofer
:
Yes
Front
:
Small
Center
:
Small
Surround
:
Small
Front High
:
Small
Surr Back
:
Small
Surr Back CH
:
2ch
38). The
(➔
(➔
8).
Error Messages
While Audyssey 2EQ Room Correction and Speaker
Setup is in progress, one of the error messages below may
appear.
2EQ: Auto Setup
Audyssey
Ambient noise is too high.
Retry
Cancel
The options are:
Retry:
Try again.
Cancel:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the source of
the noise and try again.
• Speaker matching error!
The number of speakers detected was different from
that of the first measurement. Check the speaker con-
nection.
• Writing Error!
This message appears if saving fails. Try saving again.
If this message appears after 2 or 3 attempts, contact
your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected. "No"
means that no speaker was detected.
Tip
• See "Speaker Configuration" for appropriate settings
Changing the Speaker Settings Manually
You can manually make changes to the settings found dur-
ing Audyssey 2EQ Room Correction and Speaker Setup.
See also:
• "Sp Config (Speaker Configuration)"
• "Sp Distance (Speaker Distance)"
• "Level Cal (Level Calibration)"
Using a Powered Subwoofer
If you're using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by Audyssey 2EQ Room Correction and Speaker
Setup.
If the "Subwoofer" appears on the "Review Speaker
Configuration" screen as "No", increase the subwoofer's
volume to the half-way point, set it to its highest crossover
frequency, and then try running Audyssey 2EQ Room
Correction and Speaker Setup again. Note that if the vol-
ume is set too high and the sound distorts, detection issues
may occur, so use an appropriate volume level. If the sub-
woofer has a low-pass filter switch, set it to Off or Direct.
Refer to your subwoofer's instruction manual for details.
Error message
(➔
11).
36)
(➔
37)
(➔
(➔
37)
Hide quick links:
Advertisement
Table of Contents
