Century Helicopter Products Radikal g20 User Manual
  1. Manuals
  2. Brands
  3. Century Helicopter Products Manuals
  4. Toy
  5. Radikal g20
  6. User manual

Century Helicopter Products Radikal g20 User Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
TORQUE TUBE
CONVERSION
FEATURES:
Weight savings compared to standard belt driven tail.
Metal elevator arm.
Higher efficiency.
Improved rudder control system.
Dual supported tail pitch plate.
New vertical tail fin.
Smoother tail pitch plate geometry.
Stainless steel torque tube with new bearing capture system.
© 2011 Century Helicopter Products - All rights reserved.
Version 1.00

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Radikal g20 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Century Helicopter Products Radikal g20

Summary of Contents for Century Helicopter Products Radikal g20

  • Page 1 Higher efficiency. Improved rudder control system. Dual supported tail pitch plate. New vertical tail fin. Smoother tail pitch plate geometry. Stainless steel torque tube with new bearing capture system. Version 1.00 © 2011 Century Helicopter Products - All rights reserved.

  • Page 2: General Guidelines

    (c) Purchaser Remedy- Century Helicopter Products’s sole obligation hereunder shall be that Century Helicopter Products will, at its option, (i) repair or (ii) replace, any Product determined by Century Helicopter Products to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies.
  • Page 3 TRANSMISSION BOX ASSEMBLY Torque Tube Conversion Do not open all the bags prior to starting assembly. Open the bags step by step as you go through the instruction manual. The components are bagged to make assembly easier. Make sure to apply threadlock to any screws going into metal. Description Part # CNM3x16CS...
  • Page 4 RUDDER CONTROL ROD Torque Tube Conversion NOTICE SIZE OF HOLES ON BALL LINKS THE SIDE WITH THE SMALLER HOLE SHOULD FACE OUTWARDS Part # Description CNM3x10CS HI6080B Tail Servo Mount (尾翼伺服机座) CNM2.3x12ST CNM3x10CS M3X10 Cap Screw( 杯头螺丝) HI3205A Servo Mounting Plate(伺服机固定板) CNLR1013 CNM2.3X12ST M2.3x12 Self Tapping Screws( 尖尾自攻螺丝)

  • Page 5: Torque Tube

    TORQUE TUBE Torque Tube Conversion Apply CA glue to the inner race of the bearing and glue in place as indicated. Make sure not to get any CA glue onto the dust shield/balls of the bearing. When inserting into the boom, use silicone lube. Apply CA to inner race of Center of Torque Tube bearing and glue in place...
  • Page 6 TAIL GEAR BOX Torque Tube Conversion Part # Description Tail Shaft(尾翼轴) HW6073C Threaded Spacer( 铝柱)Ø5x27 HW6078B 5x6x12.85mm Fixed Set Of( 固定套) HW6074B Ø2X9 Park Pin( 圆柱销) HW6059A HW3057A 20T Bevel Gear(20T 伞齿轮) CNBB1350 5x13x4 Bearing( 滚珠轴承) CNBB1521 Metal Bearing Sleeve( 金属轴承套) HI6079 HW6078D Gearbox Side Plate(齿轮箱侧板)
  • Page 7 TAIL GRIPS/PITCH PLATE ASSEMBLY Torque Tube Conversion Only use 1 set screw! Do not over-tighten! Use Medium CA to se- cure the ends of the pins. Part # Description HI6099A Tail Rotor Blades( 尾旋翼) HW6204A 3x10x1.5 Micro Washer( 垫片) CNM3LOCK M3 Lockmut(M3 螺母) CNBB0930 3X9X2.5 Bearing( 轴承)
  • Page 8 REAR FRAMES ASSEMBLY Torque Tube Conversion Part # Description Ø2x24 HI6145 Plastic Ball Link(塑料连杆头) HI6032GG Metal A-Arm(金属A形臂) CNM2.3x12ST HI6032GG Elevator Block For A-Arm(A 型控制臂座) HI6032G Ø2X24 Pin( 圆柱销) CNBB25F CNM2.3X12ST M2.3x12 Self Tapping Screws( 尖尾自攻螺丝) CNBB25F 2X5X2.3 Elevator Lever Flange Bearing( 带边轴承) HI6116RCG Rear Side Frame Set G20 R(20G 右后侧板) CNBB812F...

Table of Contents