Table of Contents
Advertisement
CONNECTINGTHE OVEN
Electric Supply
PRESSURES IN EXCESS OF 0.5 P.S.I. CAN DAMAGE
THE APPLIANCE PRESSURE REGULATOR AND
The appliance, when installed, must be electrically
OTHER GAS COMPONENTS IN THIS APPL(ANCEAND
groundedin accordancewith local codes or, in the absence
CAN RESULTIN A GAS LEAK.
of local codes, with the National Electrical Code,
ANSI/NFPA70.
a. A GAS CUTOFF VALVE SHOULD BE PUT IN AN
ACCESSIBLE LOCATION IN THE SUPPLY LINE
In Canadathe ovenmustbe installed inaccordance withthe
AHEAD OF THE UNIT, FOR TURNING ON AND
current CSA Standard C22.1 - Canadian Electrical Code
TURNING OFF GAS SUPPLY. If the unit is to be
Part 1.
connected to house piping with flexible or semi-rigid
metal connectors for gas appliances, CONNECTOR
ELECTRICAL SUPPLY CONNECTION:
NUTS MUST NOT BE CONNECTED DIRECTLY TO
The oven requires 120 volts, 60 cycle alternating current
PIPE THREADS. THE CONNECTOR MUST BE
from an outlet capable of supplying 15 amperes for
INSTALLEDWITHADAPTORSPROVIDEDWITHTHE
non-combo units and 20 amperes for combo units (with
CONNECTOR.
microwave).
b. The housepipingand/oroven connectorusedto connec
the oven to the main gas supply must be clean, free o
WARNING
metal shavings, rust, dirt and liquids (oil or water). Dirt
Electrical GroundingInstructions
etc. in the supply linescan causefailureof the gasvalve,=
This appliance is equipped with a (three-prong)
or controlsandctog burners.
groundingplugfor yourprotectionagainstshockhazard
and shouldbe pluggeddirectlyintoa properlygrounded
CAUTION: DONOTLIFT OR MOVETHEWALL OVEI
receptacle. Do not cut or removethe groundingprong
BY THE DOOR HANDLES.
fromthisplug,
c.Turn off all pilots and main gas valve of other ga
appliances.
WARNING
d.Turn off maingas valveat meter.
DISCONNECT
ELECTRICAL
SUPPLY
BEFORESERVICINGTHE APPLIANCE.
e. Beforeconnecting the unit,applypipethreadeompour
approvedfor LPGto allthreads.
f. Connectunitto gas supply.
Gas Supply
Installationof thisovenmust conformwith local codes or, in
g. Turn on main gas valve at meter, and relight pilots
other gas appliances.
the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1-latest edition,
h. Apply a non-corrosiveleakdetectionfluid to all joints a_
fittings in the gas connection between the supply lil
In Canadathe oven must beinstalledin accordancewith the
shut-off valve and the range. Include gas fittings a,
currentCGA StandardCAN/CGA-B149- InstallationCodes
joints in the range if connections were disturbedduri
for Gas Burning Appliances and Equipment andor local
installation.Checkfor leaks! bubbles appearingarou
codes,
fittings and connections will indicate a leak. If a I_
appears, turn off supply line gas shut-off valve, tight
GAS SUPPLY CONNECTION:
connections, turn on the supply line gas shut off val,
A TRAINED SERVICEMAN OR GAS APPLIANCE
andretestforieaks. Nevertest forgas leakswith ano_;
INSTALLER MUST
MAKE
THE
GAS
SUPPLY
flame.
CONNECTION.Leak testing of the appliance shall be
conducted by the
installer according to
the
CAUTION: NEVER CHECK FOR LEAKS WlTI_
instructionsgiven in sectionh.
FLAME.
NATURAL GAS SUPPLY LINE MUST HAVE A
WHEN LEAKCHECK IS COMPLETE,WIPEOFF
NATURAL GAS
SERVICE
REGULATOR. INLET
RESIDUE.
PRESSURE TO THIS APPLIANCE SHOULD BE
REDUCED TO A MAXIMUM OF 14 INCHES WATER
i, Adjustburnerair shutterto the widestopeningthat
COLUMN (0,5 POUNDS PER SQUARE INCH (P,S,I,)
not cause the flame to lift or blow off the burnerw
LIQUEFIED
PETROLEUM
(L.P,)/PROPANE
GAS
cold.
SUPPLY LINE MUST HAVE A L.P. GAS PRESSURE
REGULATOR.INLET PRESSURETO THIS APPLIANCE
BEFORE LIGHTING ANY BURNER, SEE THAT
SHOULD BE REDUCED TO A MAXIMUM OF 14
PACKING MATERIALS HAVE BEEN REMO\
INCHES WATER
COLUMN
(0.5
P.S.I.).
INLET
FROM THE UNITS.
-5-
Advertisement
Table of Contents
