Sony STR-DA4400ES Service Manual page 146

STR-DA4400ES
Pin No. Pin Name
AA2 to
DGND_ADC
AA4
AA23 MSTR0_SDA
AA24 MSTR0_SCL
AA25 VGA0_SDA
AA26 VGA0_SCL
AB1 A1P
AB2 SV1P
AB3 AGND_ADC
AB4 ADC_1.8V
AB23 IO_3.3V
AB24 IRO
AB25 MSTR2_SDA
AB26 MSTR2_SCL
AC1 C1P
AC2 B1P
AC3 AGND_ADC
AC4, AC5 ADC_1.8V
AC6 AGND_ADC
AC7 VOUT2
AC8 AGND_ADC
AC9 LBADC_3.3V
AC10 LBADC_IN4
AC11 LBADC_GND
AC12 AVSIN_DATA
AC13 EXTOSD_HS
AC14 IO_3.3V
AC15 OCMADDR18
AC16 IO_3.3V
AC17 OCMADDR11
AC18 IO_3.3V
AC19 OCMADDR4
AC20 IO_3.3V
AC21 OCMDATA13
AC22 IO_3.3V
AC23 OCMDATA6
AC24 OCM_CS2N
AC25 OCN_RE_N
AC26 OCN_WE_N
AD1 AN
AD2 AGND_ADC
AD3 to
ADC1_3.3V
AD5
AD6, AD7 ADC2_3.3V
AD8 AGND_ADC
AD9 RESET
AD10 LBADC_IN3
AD11 LBADC_RETURN
AD12 AVSIN_WORDSEL
AD13 EXTOSD_VS
AD14 AVSOUT_DATA
OCMADDR19,
OCMADDR15,
AD15 to OCMADDR12,
AD20 OCMADDR8,
OCMADDR5,
OCMADDR1
OCMDATA14,
AD21 to
OCMDATA10,
AD23
OCMDATA7
146
I/O
- Ground terminal
I/O Two-way data bus with the EEPROM
O Serial clock signal output to the EEPROM
- Not used
- Not used
Video signal input (PR/CR) from the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY)
I
jack
- Not used
- Ground terminal
- Power supply terminal (+1.8V)
- Power supply terminal (+3.3V)
- Not used
I/O Not used
O Not used
I Video signal input (Y) from the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) jack
Video signal input (PB/CB) from the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY)
I
jack
- Ground terminal
- Power supply terminal (+1.8V)
- Ground terminal
- Not used
- Ground terminal
- Power supply terminal (+3.3V)
- Not used
- Ground terminal
- Not used
- Not used
- Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
- Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
- Power supply terminal (+3.3V)
O Address signal output to the fl ash memory
- Power supply terminal (+3.3V)
I/O Two-way data bus with the fl ash memory
- Power supply terminal (+3.3V)
I/O Two-way data bus with the fl ash memory
O Chip select signal output terminal
O Read enable signal output to the fl ash memory
O Write enable signal output to the fl ash memory
- Not used
- Ground terminal
- Power supply terminal (+3.3V)
- Power supply terminal (+3.3V)
- Ground terminal
I Reset signal input from the video system controller
- Not used
- Not used
- Not used
- Not used
- Not used
O Address signal output to the fl ash memory
I/O Two-way data bus with the fl ash memory
Description
Not used
"L": reset