Table of Contents
Advertisement
CHAP.02 ACCIDENT PREVENTION /
SAFETY REGULATIONS
02.1
GENERAL CONSIDERATIONS
•The manual refers to essential aspects of the directives, regula-
tions and dispositions on using the machine, summarising its most
significant points.
•General legal regulations and mandatory rules regarding injury
prevention and environmental protection must be observed. These
obligations also include regulations regarding the use of personal
protective equipment.
•For all work to be done on the system, the following dispositions
and regulations in force must be observed regarding accident pre-
vention, following the indications.
• Before using the system the first time, the user
must have read and understood the instruction ma-
nual perfectly and this chapter in particular.
•The user must also make sure that the machine is always in good
condition as regards its safety requirements.
•During maintenance and inspection activities, wear the following
specified protective garments.
Important: cleaning and maintenance interventions
must only be performed on cold fireplaces/stoves,
preferably with the electricity supply open, i.e. in the
ZERO, OFF position.
•Danger warnings and signals in the form of plates, labels and
markings must not be removed or made unidentifiable. If they are
worn or broken, they must be replaced.
•Modifications, additions or transformations must
not be made on the machine and its components wi-
thout the manufacturer's authorisation. This is valid
first and foremost for installation and regulation of
the installed safety devices. Failure to comply with
this warning relieves the Manufacturer of all and any
responsibility.
•Make sure, before starting up every time and after carrying out
maintenance, that dismantled parts have been repositioned cor-
rectly and in particular all the protection devices that impede ac-
cess to the machine.
02.2
SAFETY REGULATIONS FOR ROUTINE
MAINTENANCE AND USE
• THE USER AND/OR OWNER OF THE PRODUCT
IS REQUIRED, IN ACCORDANCE WITH THE LAWS
IN FORCE, TO ASSIGN THE INSTALLATION AND
MAINTENANCE TO QUALIFIED AND SPECIALISED
OPERATORS, AND ACKNOWLEDGE THE RISKS
AND HAZARDS SHOULD THEY FAIL TO OBSERVE
THIS REQUIREMENT.
•Use of this product is not permitted for children, persons with
acknowledged reduced psycho-physical and sensory abilities and
persons who lack experience in using such machines, unless they
are supervised by designated persons responsible for their safety.
•The settings and programming of the product must only be per-
formed by adults who have received suitable and specific training.
Errors or incorrect settings can create hazardous conditions and
trigger malfunctions with relative consequences for persons and
things.
•Before any cleaning and/or routine or extraordinary maintenance
on the machine, disconnect it from all energy sources; in particular,
turn the electrical power switch to ZERO.
•Prior to installation, the user and installer are obliged to check
that the mains electrical supply to which the machine will be con-
nected, corresponds to the voltage on the identification plate (see
CHAP.04.2-PRODUCT IDENTIFICATION), and that it is equipped
with all suitable safety devices to classify the electrical system as
COMPLIANT with applicable safety standards. If this is not the
case, contact a Qualified Technician to adapt the system to requi-
red standards.
•Upstream from the machine (at the user's expense) on the electri-
cal power supply line, a bipolar switch must be installed that is able
to intercept all the current phases. (See CHAP.05 - TECHNICAL
DATA for calculations).
•The irradiation area includes the area between the opening of the
hearth and up to 1 metre of space frontally as well as laterally. No
inflammable object must be left in this area, such as: inflammable
liquids, fire-starting products or firewood, drapes, wooden decora-
tions, rugs, etc.
•Do not use the stove to dry clothes, it could overheat and cause
an outbreak of fire.
•ATTENTION - BEWARE OF BURNS, most of the outer
surfaces of the stove are very hot, door handle, glass,
metal sides, majolica or metal top, fume exhaust pipe
etc. Never touch the stove with naked hands when it
is running; always use heat protection gloves, such as
those supplied with the stove, when handling all parts.
•Before doing any internal cleaning or maintenance, you must wait
until the machine reaches the ambient temperature.
•If the stove is in alarm status due to a malfunction, do not attempt
to restart it before finding out what has caused the heat generator to
shut down.
•Never wash the internal parts of the combustion chamber with water.
•In alarm status for failed start up, do not try to restart the stove until
the firebox has been thoroughly cleaned.
•The stove must always be started up with the firebox empty, without
PELLETS and without unburned fuel from previous use.
•Do not attempt to ignite the fuel with inflammable liquids or solids; the
stove must ignite automatically via the electrical components installed
onboard.
•Do not load PELLETS manually into the firebox before or whilst the
stove is running.
•Keep the ventilation grids in the area the stove is installed in clean
conditions.
•Never load any fuel other than PELLETS into the stove storage hop-
per. Corn, nuts or other combustible materials must not be used as
fuel for the stove.
•Check and periodically clean the fume exhaust pipe, from the stove
to the flue (Union).
•IT IS STRICTLY PROHIBITED TO START UP THE
PRODUCT WITH THE COMBUSTION CHAMBER
DOOR OPEN OR ALLOW IT TO RUN WITH THE
GLASS BROKEN.
•The user should contact an authorised JOLLY-MEC Technical
Assistance Centre if any operating problems persist.
5
Advertisement
Table of Contents
