Jolly Mec I-DEA Quadra Installation, Use And Maintenance Manual page 39

I-dea series air and pellet stove
Table of Contents

Advertisement

• Control unit main alarms
NUMBER ALARM NAME
AL1
BLACK
OUT
AL2
EXHAUST
PROBE
AL3
HOT
EXHAUST
AL4
FAN
FAILURE
AL5
NO
LIGHTIN-
CAUSE
• Electrical black out
• The electric plug has discon-
while the stove is run-
ning
• The electric plug has discon-
• The electrical wiring connec-
• The fuses installed on the elec-
• The electrical con-
• The fumes probe could be worn
nection is not correct
• The flue probe is bro-
ken
• The fumes tempera-
• The fume probe is positioned
ture is over 270°C
• The air exchange fan is not wor-
• The stove is exceptionally dirty
• The PELLET load is excessively
• The control unit does
• The fumes extractor electrical
not detect the correct
number of fumes ex-
• The "ENCODER" speed sensor
tractor rpm
• The combustion fan is broken
• The combustion fan is very dirty,
• The DELTA TRUN
• The start-up electrical element
ON setting has not
been reached within
• The electrical element guide
the maximum start-
up time
• The PELLET loading during the
• The fumes extractor fan speed
• The firebox may be positioned
• The firebox could be exceptio-
MAIN REASONS
nected from the mains socket
nected from the stove socket
tor has disconnected from the
electronic circuit board terminal
board
tronic circuit board have blown
or broken due to accidental fric-
tion
incorrectly
king
high
connection is incorrect or faulty
plug is disconnected.
and is not revolving
to the extent where it decreases
its speed
may be broken
tube could be very dirty and
clogged with ash.
start-up phase could be higher
or lower than the amount cali-
brated by Jolly-Mec
is too high or too low during the
start-up phase
incorrectly
nally dirty
MAIN REMEDIES
Check that the power cord is
connected properly to both
the mains socket and the
stove socket
Check that the connectors
are well connected to the
electronic circuit board ter-
minal board (test this with
the power cord discon-
nected).
Check the fuses are OK (do
this test with the power cord
disconnected)
• Check that the probe is con-
nected to the electronic circuit
board correctly. RED wire to ter-
minal +, blue wire to terminal
• Check that the thermocouple
wires are intact, and there are
no continuity interruptions
• Contact the Jolly-Mec Techni-
cal Assistance Centre
• Check the position of the fumes
probe
• Check to see if the air exchange
fan is running properly
• Check to see if the stove is dirty,
and clean it if necessary
• Check to see if the PELLET load
settings are correct
• Contact the CAT if this type of
alarm is tripped frequently
• Check that all the electrical con-
nections are in order
• Check to see if the combustion
fan is very dirty
• Check to see if a foreign body
has accidentally been caught up
in the fan or the external motor
• Contact the CAT if this type of
alarm is tripped frequently
• Check the efficiency of the elec-
trical element
• Check that the element guide
tube is clean
• Always check that the firebox is
perfectly clean before the start-
up phase
• Before restarting the stove, it is
necessary to empty the firebox,
that is restarting the stove with a
clean firebox.
• Check the PELLET preloading
quality. The level must be slightly
above the electrical element hole
during the preloading phase
• Check that the PELLET load
and fumes extractor fan speed
settings are correct
39

Advertisement

Table of Contents
loading

This manual is also suitable for:

I-dea frontaleI-dea angolo

Table of Contents