Personalisations; Setting The Temperature; Setting The Spin Cycle; Functions - Ariston AVTF 129 Instructions For Use Manual

Personalisations

Setting the temperature

If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs
to be regulated, a fixed
set will be displayed and the
which indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value,
after approximately 2 seconds the setting is accepted: the symbol
The temperature adjustment is enabled with all wash programmes.

Setting the Delay Timer

Press the button
Press the button again and "1h" appears, that is, a delay of one hour (this can reach up to 24h); stop on the
"desired" delay; after approximately 2 seconds the setting is accepted, following which, the time for the set
programme appears on the display and the symbol
If you now press the START/RESET button, the set "delay" appears; this decreases every hour until the start of
the cycle. In this phase, the "delay" can only be modified by decreasing it.
The Delay Timer regulation is enabled with all programmes.
Keyboard lock

Functions

To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
If you set a function that is incompatible with another function you selected previously, only the last one selected
will be enabled.
Funct i on Ef f ect
Su per Al l ows f or an
Was h i mpeccabl e
was h , vi s i bl y
wh i t er t h an a
s t an dar d
Cl as s A
was h .
Eas y i r on Th i s o pt i o n
r edu ces t h e
amo u n t of
cr eas i n g on
f abr i cs ,
mak i n g t h em
eas i er t o
i r on .
Rapi d Cu t s t h e
du r at i on of
t h e was h
cycl e by 30%.
Downloaded From WashingMachine-Manual.com Manuals

Setting the spin cycle

If, when the appliance is switched on, the KNOB is positioned on a
programme with a spin cycle, a fixed
and the maximum spin speed allowed for the programme set will be
displayed, and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the maximum
value); stop on the desired speed, after approximately 2 seconds
the setting is accepted: the symbol
The spin cycle setting is enabled with all the programmes except for
11 (curtains, silk) and the Draining cycle.
appears. Press button
icon flashes. Press it again and the temperature lowers until it reaches OFF,
and you will see the word OFF on the display, while the relative symbol flashes.
(See page 17)
Comment s
Th i s f u n ct i on i s i n compat i bl e wi t h t h e RAPI D
f u n ct i o n .
Wh en t h i s f u n ct i on i s s et , pr ogr ammes 6, 7, 8, 11
an d Del i cat e r i n s e wi l l en d wi t h t h e l au n dr y l ef t t o
s oak ( An t i - cr eas e) an d t h e EASY I RON bu t t on f l as h es :
- t o con cl u de t h e cycl e, pr es s t h e START/RESET
bu t t on or t h e EASY I RON bu t t o n ;
- t o r u n t h e dr ai n i n g cycl e al on e, s et t h e k n ob t o
t h e r el at i ve s ymbol
bu t t on .
Th i s f u n ct i on i s i n compat i bl e wi t h t h e SUPER WASH
f u n ct i o n .
the icon goes on. Press it again and the
and the maximum temperature allowed for the programme
remains fixed.
remains on.
an d pr es s t h e START/RESET
appears. Press button
remains fixed.
Enabl ed wi t h
pr ogr ammes:
1 , 2 , 3 , 4 ,
5 , 6 , 7 , 8
A l l
pr ogr ammes
ex cept f or
1 , 2 , 9 , 1 0
and
Dr ai ni ng.
1 , 2 , 3 , 4 ,
5 , 6 , 7 , 8
Ri nses
19
GB