Install Hood - Broan allure QS3 series User Manual

INSTALL HOOD

KEYHOLE (4)
1 Hang hood from (4) Mounting Screws. Slide hood towards
wall until mounting screws are engaged in narrow end of (4)
Keyholes. Tighten mounting screws securely. A long
screwdriver works best.
2 Replace bottom cover.
3 Connect ductwork to hood. Use Duct Tape to make joints
secure and air tight.
4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16,
40 W Maximum Incandescent Bulbs. Purchase bulbs
separately.
!
CAUTION:
Bulbs may be hot! Refer to bulb packaging
for further information.
5 Replace filters, turn on power at service panel, and test for
proper operation.
®
MOUNTING SCREW (4)
PAR20,
50W MAX.
HALOGEN
BULB (2)
- or -
R16,
40W MAX.
INCANDESCENT
BULB (2)
OPERATION
Fan: 4 push button switches. Push any button to select one of the four fan speeds.
Press another button to change fan speed. Push the same button to turn fan off. A
light above each fan button indicates the fan speed.
Lights: Press "on/off" button and lights will come on at their previous light level.
Press button again to turn lights off. To increase light level, press the "+" button. To
reduce light level, press the "-" button. There are 3 light levels to select.
Delay Off: While fan is running, press the "delay" button to allow the fan to run for 10
minutes and then turn itself off.
Filter Change Indicator: The light above "filter" will come on when it is time to clean
your grease filters or check your non-ducted filters. After replacing the cleaned, or
new filters, press the "filter" button to turn off the indicator light.
Heat Sentry System: Your range hood is equipped with an advanced Heat Sentry
system.
The advanced Heat Sentry system monitors temperature and automatically adjust
the fan to the appropriate setting.
1) If the fan is on, the Heat Sentry system will increase the fan setting when the
temperature is elevated. If the temperature continues to rise, the Heat Sentry
system will continue to increase the fan setting until the temperature is stabilized
or reduced. The flashing light above the fan button shows the Heat Sentry system
fan setting. Once the temperature has reduced, the Heat Sentry system will
change the fan to the original setting.
2) If the fan is on or off, the Heat Sentry system will automatically turn the fan on at
its highest speed when the temperature is above normal. When the Heat Sentry
DUCT
system is on, the light above the fan button B (Boost) will flash on and off. After
TAPE
the temperature has lowered to normal, the fan will change to the setting prior to
the Heat Sentry turning on.
Fuse: The hood control contains a fuse to protect it from power surges. If the fuse
has opened (blown), the green fan-level indicators will operate properly when the fan
buttons/switches are pressed - but the fan and lights will not turn on.
The fuse is a 5 x 20 mm, 10 Amp, Fast-Acting, 125V (min.). Common manufacturer
and part numbers are: Littlefuse, 217010; Bussmann, GMA10A; Wickmann, 1942100.
Radio Shack, Digikey (1-800-344-4539), and most electronic supply stores have
them in stock.
To replace the fuse:
1. Disconnect power at service entrance.
2. Remove filters, bottom panel, light wire harness, and air chute.
3. Remove and inspect fuse. If it is not open (blown), additional diagnostics need to
be done.
4. Install new fuse.
5. Re-assemble air chute, light wire harness, bottom panel, and filters.
6. Turn on power and check hood/control operation.
CLEANING
WARNING: To reduce the risk of electric shock,
disconnect from power supply before cleaning.
Aluminum mesh filters: Clean frequently using hot water and a mild detergent.
Filters are dishwasher safe.
Charcoal filters: Clean filter surfaces frequently with a damp cloth and a mild
detergent. DO NOT immerse filters in water or put in dishwasher. The special "Clean
Sense" feature indicates when the filter is to be replaced. The blue and yellow strips
will blend to green when it is time to change the filter. The "Clean Sense" feature
works best when facing toward the cooking surface.
To clean hood: Remove filters. Use a damp cloth and a mild detergent to wipe all
grease-laden surfaces. Do not use abrasive cloth, steel wool pads, or scouring
powder on the Teflon
cleaning blower wheel - it must not become bent or misaligned. DO NOT ALLOW
WATER TO ENTER MOTOR. Make sure all surfaces are completely dry before re-
installing filters and restoring power.
Motor is permanently lubricated. Do not oil or disassemble motor.
®
Teflon is a registered trademark of DuPont.
ALLURE
® -coated bottom cover or on any painted surface. Use care when
®
QS3 SERIES
RANGE HOOD
Page 5