Subscribe to Our Youtube Channel
Related Manuals for Eckman EKECS03
Summary of Contents for Eckman EKECS03
-
Page 1: Instruction Manual
2400W ELECTRIC CHAIN SAW MODEL EKECS03 INSTRUCTION MANUAL PLEASE READ AND SAVE THE INSTRUCTION MANUAL FOR FUTURE REFERENCE Any questions please call the Eckman helpline on：0844 441 3011 or go to www.eckman.co.uk... -
Page 2: Table Of Contents
- 1 - Contents Environmental protection ..................- 2 - Safety instructions ....................- 2 - Description of symbols ..................- 2 - Safety rules ......................- 3 - Technical data ......................- 5 - Parts identification ....................- 6 - Setting chain and chain bar ................ -
Page 3: Environmental Protection
- 2 - Environmental protection Waste electric products should not be disposed of with household waste. Please recycle check with your local Authority or retailer for recycling advice. Safety instructions Before using the chainsaw, please read the following instructions and follow them during operation! Please “Save all warnings and instructions for future reference”. -
Page 4: Safety Rules
- 3 - Safety rules – general and for electric chainsaws 1. Replacement Parts. When servicing, use only identical replacement parts. 2. Plugs. Do not modify the plug connected to the power lead in any way. 3. Cleanliness. Keep Work Area Clean. Cluttered areas invite injuries. Do not start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree. - Page 5 - 4 - Inspect periodically and if damaged, have repaired by authorized service facility. Keep mains power lead clear of the chain and operator at all times. Never carry saw by the mains lead and keep cord away from oil and sharp edges. Keep the chain sharp, clean, and properly tension-adjusted for better and safer performance.
-
Page 6: Technical Data
⑦. Only use replacement bars and chains specified by the manufacturer or the equivalent. 20. Power Supply. Connect chain saw to correct voltage, that is, be sure that the voltage supplied is the same as that specified on the nameplate of the tool. Technical data Factory Model/Eckman Model SF7J101/EKECS03 Voltage 230V-50HZ... -
Page 7: Parts Identification
- 6 - Start Type Soft Touch Start Function of LED Indicator Power Overload Indicator Parts identification Cable + plug (UK plug supplied) Rear handle On/Off switch Lock-off button Oil Tank cap Front handle Activation lever for kickback brake (hand guard) Nose sprocket Oregon bar Oregon Chain... -
Page 8: Setting Chain And Chain Bar
- 7 - Setting chain and chain bar Chain and chain bar assembly for model with SDS tool-less tensioning system Place the chainsaw with the motor on a cover to avoid any mess from the oil. Place the chain in the grove of the bar. Pay attention to the correct running direction. -
Page 9: Setting The Chainsaw Tension
- 8 - Setting the chainsaw tension Tensioning chain for model with SDS tool-less tensioning system Loosen the lock knob by turning it anti-clockwise approximately 1-2 turns. Check whether all chain links lie correctly in the guide tracks of the bar. Press the tension ring inwards and turn it in a clockwise direction until the correct chain tension is reached The correct tension is reached when the chain in the middle of the bar can only be raised by... -
Page 10: Checking The Automatic Oil Function
- 9 - Checking the automatic oil function Switch on the chainsaw, rev it up and point the tip of the saw towards a piece of paper laying on the ground. If a patch of oil appears and becomes larger, then the automatic oil function is working. -
Page 11: Operating The Electric Chain Saw
- 10 - Note. Ensure the brake is working efficiency, check its operation every time you use the chain saw before commencing work with it WARNING. The trigger must never be depressed before pulling back the front hand guard. 1.Hold the electric chain saw by its grip with both hands. 2.To start the chainsaw, squeeze the trigger lock-out, then squeeze the trigger Lock-out button Trigger... - Page 12 - 11 - 2. Reset the gripping teeth at a lower point when sawing thicker logs by pulling the chain saw slightly backwards, until the gripping teeth release, and reposition at lower level to continue sawing. Do not remove the saw completely from the wood. 3.
- Page 13 - 12 - ●To fell trees, observe all the safety regulations and proceed as follows: The chainsaw may be used to fell only trees which are smaller in diameter than the length of the bar and chain. If the saw chain gets jammed, release it using a wooden wedge. ●Felling trees is dangerous and requires practice.
-
Page 14: Chain Brake
- 13 - Chain brake In the event of kick-back, the chain brake will be actuated via the front finger guard. The front finger guard is pushed forwards by the back of the hand and this causes the chain brake to stop the chain saw, or rather the motor, within 0.15 of a second. -
Page 15: Chainsaw Maintenance
- 14 - Chainsaw maintenance WARNING. Always ensure that the machine is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. 1. Always keep the air holes clean on the electric chainsaw body. They tend to become clogged with sawdust during use and this affects the efficiency of cooling, causing overheating of the motor. -
Page 16: First Time User
- 15 - is always greater than the chain’s transmission links so that the latter do not touch the bottom. Replace the bar if required. The chainsaw should be periodically serviced to check the correct operation of the chain, chain drive, motor and brake. -
Page 17: Guarantee
- 16 - Blunt saw chain Sharpen or replace the saw chain. Chain tension Check chain tension. Poor cutting performance chain fitted Check saw chain incorrectly Chain jumps off guide bar Chain tension Check chain tension. Chain works with difficulty Chain tension Check chain tension. -
Page 18: Ec Declaration Of Conformity
Development Zone,Yongkang, Zhejiang China hereby declare by our own responsibility that the product : CHAIN SAW ,TYPE SF7J101-24-SLN (EKMAN MODEL EKECS03) Is according to the basic requirements ,which are defined in the European directives : 2004/108/EC Annex II (EMC Directive) - Page 19 - 18 -...
- Page 20 - 19 -...
Need help?
Do you have a question about the EKECS03 and is the answer not in the manual?
Questions and answers