Notice - Sanyo FW50C85T Owner's Manual

1 Notice

SANYO is a registered trademark of SANYO Electric Co., Ltd.
and is used by Funai Electric Co., Ltd. and Funai Corporation, Inc.
under license from SANYO Electric Co., Ltd.
Any liability related to SANYO products, including design and
quality, is the sole responsibility of Funai Electric Co., Ltd. and
Funai Corporation, Inc.
Please contact Funai Corporation, Inc. for any questions or
claims related to SANYO products: sanyo-av.com
Funai reserves the right to change products at any time without
being obliged to adjust earlier supplies accordingly.
The material in this Owner's Manual is believed adequate for the
intended use of the system. If the product or its individual
modules or procedures are used for purposes other than those
specified herein, confirmation of their validity and suitability must
be obtained. Funai warrants that the material itself does not
infringe any United States patents. No further warranty is
expressed or implied.
Funai cannot be held responsible neither for any errors in the
content of this document nor for any problems as a result of the
content in this document. Errors reported to Funai will be
adapted and published on the Funai support website as soon as
possible.
Pixel characteristics
This LCD product has a high number of color pixels. Although it
has effective pixels of 99.999% or more, black dots or bright
points of light (red, green or blue) may appear constantly on the
screen. This is a structural property of the display (within
common industry standards) and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove
covers to the inside of the product. Repairs may only be done by
Service Centers and official repair shops. Failure to do so shall
void any warranty, stated or implied.
Any operation expressly prohibited in this Owner's Manual, any
adjustments or assembly procedures not recommended or
authorized in this Owner's Manual shall void the warranty.
Federal Communications Commission Notice
This equipment has been tested and found to comply with
the limits for a Class B Digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio or television
technician for help.
Declaration of Conformity
Trade Name : SANYO
Responsible Party
: FUNAI CORPORATION, Inc.
Model
: FW50C85T
Address
: 19900 Van Ness Avenue, Torrance, CA 90501
U.S.A.
Telephone Number
: 1-800-877-5032
Modifications
This apparatus may generate or use radio frequency energy.
Changes or Modifications to this apparatus may cause harmful
interference.
Any Modifications to the apparatus must be Approved by Funai.
The user could lose the authority to operate this apparatus if an
unauthorized Change or Modification is made.
Cables
Connections to this device must be made with shielded cables
with metallic RFI / EMI connector hoods to maintain compliance
with FCC Rules and Regulations.
The following FCC is description of Wireless
LAN adapter.
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Country Code Statement
For product available in the USA market, only channel 1∼11
can be operated. Selection of other channels is not
possible.
To maintain compliance with FCC RF exposure
requirements, use only belt-clips, holsters or similar
accessories that do not contain metallic components in its
assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure
requirements and should be avoided.
5150-5250 MHz band is restricted to indoor operations only.
High-power radars are allocated as primary users (i.e.
priority users) of the bands 5250-5350 MHz and
5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which
is the passed down through the MAC, through the
digital and analog baseband, and finally to the RF chip.
Several special packets are initiated by the MAC. These
are the only ways the digital baseband portion will turn
on the RF transmitter, which it then turns off at the end
of the packet. Therefore, the transmitter will be on only
while one of the aforementioned packets is being
transmitted. In other words, this device automatically
discontinue transmission in case of either absence of
information to transmit or operational failure.
5 .
English