Sanyo FW50C85T Owner's Manual page 40

Manually enter your SSID
Set up the connection to the AP (e.g. Wireless Router) manually by
entering the SSID.
3
Use H I to Select Manually enter your SSID, then press OK.
AP (e.g. Wireless Router) SSID entry screen will appear.
●
Enter the SSID using H I J K, then press OK.
4
Use H I to Select the authentication setting of the selected
wireless network.
For a wireless network with authentication setting, select the
●
authentication setting, according to the security type of the
wireless network.
Auto XXXXXXXXXXXXXX
Manually enter your SSID
None Set the authentication setting to None.
WEP Set the authentication setting to WEP
WPA/WPA2 Set the authentication setting to WPA/WPA2
For a wireless network without authentication setting, select None.
●
If you select WEP or WPA/WPA2, WEP
● *
screen will appear. Enter the WEP
wireless network using H I J K, then press OK.
Confirmation message will appear. Select Yes to complete the
●
settings.
* WEP is not recommended to be used due to its Major security flaws.
Change the Security protocol on the Wireless Router to WPA or WPA2
(recommended) mode.
None
WEP
WPA/WPA2
.
*
/ WPA / WPA2 Key entry
*
/ WPA / WPA2 key of the selected
*
IP configuration
In following cases, select IP configuration to set each setting as
necessary.
When Connection Test failed with the setting of Connection test.
–
When instructed by your Internet service provider to make specific
–
settings in accordance with your network environment.
2
Use H I to Select IP configuration, then press OK.
3
Use H I to Select a setting, then press OK.
Network selection IP setting mode
Wireless network setting IP address
IP configuration Subnet mask
Proxy configuration Default gateway
DNS setting mode
Primary DNS
Secondary DNS
MAC address
Auto Sets the IP setting automatically.
IP setting
mode
Manual
Sets the IP setting manually.
A set of numbers which are assigned to
IP address devices participating in a computer
*1, 3
network.
A mask which is used to determine what
Subnet mask
*1, 3
subnet an IP Address belongs to.
IP Address of the network device (such as
Default gateway
*1, 3
router) which provides Internet access.
Auto Sets the DNS setting automatically.
DNS setting
mode
Manual Sets the DNS setting manually.
A server which handles the name and IP
Primary DNS
*2, 3
Address over the Internet.
A server which handles the name and IP
Secondary DNS
*2, 3
Address over the Internet.
An address which recognizes the devices
MAC address
connecting to the network. It is also called
Hardware Address.
Items can be selected only when IP setting mode is set to
*1
Manual.
Items can be selected only when DNS setting mode is set to
*2
Manual.
Use H I or the NUMBER buttons to input numbers. When you
*3
use H I to input numbers, then press OK or input the triple digits
by using the NUMBER buttons, the cursor moves to the next
entry field. When you use H I to input numbers, then press OK
or input the triple digits by using the NUMBER buttons at the
rightmost entry field, numbers will be stored and go back to the
previous menu.
Note(s)
The range of input numbers is between 0 and 255.
●
If you enter a number larger than 255, the number will automatically be 255.
●
The manually entered number will be saved even if you change the setting to Auto.
●
If you want to enter 1 or 2 digit number in one cell, press OK to move on to the next cell.
●
If the entered IP Address or the default gateway or primary DNS number is same as the
●
default setting, IP Address setting will be set to Auto. (The manually entered number will
be saved).
When IP address setting is set to Manual, the setting of DNS setting will automatically be
●
Manual and when IP address setting is set to Auto, you can set either Auto or Manual for
DNS setting.
40 .
English
Auto
Manual
Continued on next page.