Plug-In Surface Units; Tilt-Lock Surface Units; Cooktop Surface Lamp; To Reposition Surface Unit - Hotpoint RB731 Use And Care Manual

~ Hold glass cover and remove
screw. Pull glass cover forward,
then down and remove.
~'Replace lamp with 40-watt
appliance lamp.
--=43
To replace:
G Tuck extension on glass cover
into back of lamp opening.
~ Fit cover over opening and
replace washer and screw. (When
removing and replacing cover, if
,,*=. thermostat tube should be moved
-&<——-
out of place, be certain it is
-=5ZY
returned to its Proper horizontal
~osition, and abou"t% inch from
over.)
~ Connect electric power to range.
..-
:. :Xlktop 5LJ14="
~+"~e Lamp
WHEN
iX-IANGHW A
COOKT'OP L4Jw, Do N(YI'
TOUCH THE
METAL AT'ENDS
OF LAMP.
::. Hold glass panel assembly and
remove the three screws from metal
frame which holds top of assembly
in place.
;'. Hold assembly in both hands,
]Owel- i t until it is removed.
I Remove lamp(s) and replace with
~~l]bof the same wattage, Lift glass
panel assembl~:into place and
r:place screws In top of assembly
10hold it in place,
.'. Connect ciectric power to range.
-------
<"
- .%
">
1
?
..
-.--'
Hug-h SWfi3cc U1'-ii%
(on Models so equipped)
Clean the area under the drip pans
often. Built-up soil, especially
grease, may catch fire, To make
cleaning easier, the plug-in surface
units are removable.
RECEPTACLE
MEDALLION
I
.
TERhllNALS
CHROME-PLATEO
SPIOER
ORIP PAN/RING
I /"
R
RIN
To clean:
@Wipe around the edges of the
surface unit opening in the range
top. Clean the area below the unit.
Rinse all washed areas with a damp
cloth or sponge.
Caution: Be sure all controls are
turned OFF before attempting to
clean under the cooktop or re-
movirig the Calrod@units.
To remove:
~ Raise the unit coil opposite the
receptacle, Lift about one inch
above the trim ring and pull away
from the receptacle. Caution: Be
sure the coils are cool before re-
moving a Calrod@unit,
~ After removing the plug-in sur-
face unit, lift the drip pan/ring to
clean under the unit.
To replace:
~~Place the drip pan/ring in the
surface unit cavity found on top of
the range. Line up the drip pan so
the unit receptacle can be seen.
: insert the terminals of the plug-
in unit through the opening in the
pan/ring and into the receptacle.
~~Guide the surface unit into place
so it fits evenly and fits snugly into
drip pan or trim ring.
N'ote:~fyour range has separate
trim rings, the drip pan must be
under the
ti";m
ring.
2-/
Do not attempt to clean plug-in
surface units in an automatic
dishwasher.
Do not immerseplug-in surface
units in ~iquidsof any kind.
Do not bend the plug-in surface
unit plug terminals.
Do not attempt to clean, adjust
or in any way repair the plug-in
receptacle.
~~hf% Ud$j
Tilt-Lock surface units can be lifted
upward and locked in that position
for cleaning under unit. Be certain
unit is COO] before liftingcoil up.
After lifting coil unit, remove trim
ring and drip pan to clean under
unit. Clean pan and trim ring as
recommended on Cleaning Chart
on pages 29 and 30.
~f-j
Reposition FjhH'face I unk
o Replace drip pan into recess in
cooktop.
Q Put trim ring in place over drip
pan.
o Guide the surface unit into place
so it fits evenly into trim ring. Pan
must be under trim ring.
— -... .... . . ..-— —- —-—----— ------------- .---—— --- ~ —-
—T--—-
—.