How To Care For Your Range; Finishes; Cleaning Under The Range; Oven Lamp - Hotpoint RB731 Use And Care Manual

The porcelain enamel finish is
sturdy but breakable if misused.
This finish is acid resistant. How-
ever, any acid foods spilled (such
as fruit juices, tomato, or vinegar)
should not be permitted to remain
on the finish.
The area under the range of models
equipped with a bottom drawer can
be reached easily for cleaning by
removing the bottom drawer. To
remove, pull drawer out all the way,
tilt up the front and remove it, To
replace, insert glides at back of
drawer beyond stop on range glides.
Lift drawer if necessary to insert
easily. Let front of drawer down,
then push in to close.
R.ermwdbk
Cl%
Jei-ilDoor
;Si---------
-l"\
To REMOVE door, open to BROIL
position, or where you feel hinge
catch slightly. Cirasp door at sides;
iift door up and away from hinges.
To REPLACE, grasp door at sides.
Line
LIp
door with hinges and push
door firmly into place.
T$r i
t,-%
.!, ;,, <.,
, >7
,)
:s::[ ;:<j~-r:-.";
.. .>
-d .
}Totlr ~ange is
vented
~hI'OUgh ~
duct
Iocatcd under the right rear
surfticc unit. Clean the duct often.
Proper care and cleaning are
Lmatious Sb[}wnfor: .:=- -'
important so your Range will give
1 Oven Vent Duct
you efficientand satisfactory
service. Followthese directions
2 Calrod@Surface Units
:-
carefully in caring for your range
3 Oven Lamp
..
&e
to assure safe and proper
F
/-;
-~<
"\L___
'7
To remove:
@Make sure unit is cool.
@Lift up right rear surface unit.
@Remove drip pan and ring.
a Lift out oven vent duct.
To replace:
e
place the part over
the
oven
vent
located below the cooktop with
opening of the duct under the
round opening in the drip pan. It is
important that the duct is in the
correct position so moisture and
vapors from the oven can be
released during oven use. NOTE:
Never cover the hole in the oven
vent duct with aluminum foil or
any other material. This prevents
the oven vent from working prop-
erly during any cooking cycle.
oven I.an%p
CAUTION: Before replacing your
oven bulb, disconnect the electrical
power for your range at the main
fuse or circuit breaker panel or pull
plug. Be sure to let the lamp cover
and bulb cool completely before
removing or replacing.
To remove:
Q Remove the 3 slotted screws in
the lamp cover as shown in
diagram.
@Detach lamp cover and remove
bulb.
To replace:
@Put in a new 40-watt appliance
bulb.
@Install lamp cover. Replace 3
screws and tighten, making sure
cover fits flush with oven wall.
@Reconnect electrical power to the
range.
To Clean {Jppel"oven Panels lb.
self-cleaning O'ven
Place shelf from upper oven on
either shelf of self-clean oven.
(Shelf may have to be shifted
slightly so shelf stops do not inter-
fere with placement of paneis.)
Slide out oven bottom; lifting bake
unit slightly makes this easier to do.
Lift back panel and remove. Place
bottom and back panels back-to-
back so soiled sides face outward.
Place these panels over shelf on
STRAIGHT shelf. It is important
that panels lay flat on shelf.
Lift side panels up and out of oven.
Place back-to-back on remaining
self-clean shelf.
To Replace Pain'elsIn
'Llppe3" o wn
Replace panels in any order
desired. Be certain oven bottom is
replaced so notch is at right, and
"feet" on bake unit rest in depres-
sions in panel. Replace broiler
reflector so "open side" is toward
bottom of oven.
— ———————. .. ... . ..-.———
— — ....
,. - --—
.....