Table of Contents
Advertisement
05
3
Specify whether to turn Parental Lock on or off.
! OFF – Internet services are not restricted.
! ON – Internet services are restricted.
4
If you want to change the password, select Change Password.
In this case, the procedure returns to step 2.
Play ZONE Setup
VSX-90 only
You can select what zone to play when playing via AirPlay and Bluetooth equipped devices as well as when play-
ing audio content on equipment in the home network in DMR mode.
! For playable DLNA-compatible network devices, see
1
Select 'Play ZONE Setup' from the Network Option menu.
2
Select the zone in which you want to play the audio contents.
3
When you're finished, press RETURN.
You will return to the Network Option menu.
Notes
! If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off,
then play the audio contents.
! MAIN/HDZONE at ZONE Setup must be set to HDZONE in order to use the HDZONE function
Port Number Setting
VSX-90 only
On this receiver, there can be up to 5 numbers of ports where signals are received.
1
Select 'Port Number Setting' from the Network, Bluetooth menu.
2
Select the port number you want to change.
3
Input the port number.
! Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.
! It is not possible to set the same port number more than once.
4
If there are other port numbers you want to change, repeat steps 2 and 3.
Note
We recommend setting the port number to 00023 or within the range of 49152 to 65535.
Automatically conducting optimum sound tuning (Full Auto MCACC)
The Full Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account
ambient noise, speaker connection and speaker size, and tests for both channel delay and channel level. When
Measurement Type is Expert, in addition to this, Standing Wave, Reverb chracteristics, Full Band Phase
Control (VSX-90 only) and EQ are measured. After you have set up the microphone provided with your system, the
receiver uses the information from a series of test tones to optimize the speaker settings and equalization for your
particular room.
page 79
.
(page 114
Important
! Make sure the microphone and speakers are not moved during the Full Auto MCACC Setup.
! Using the Full Auto MCACC Setup will overwrite any existing settings for the MCACC preset you select.
! Before using the Full Auto MCACC Setup, the headphones should be disconnected.
! With factory default settings, the on-screen display will be output from all HDMI output terminals and dis-
played on any TV connected via HDMI cable.
VSX-90 only: You can change where the screen is output in the MAIN/HDZONE
(page 92
) settings.
CAUTION
! The test tones used in the Full Auto MCACC Setup are output at high volume.
1
Press u STANDBY/ON to switch on the receiver and your TV.
Make sure that the TV's video input is set to this receiver.
2
Connect the microphone to the MCACC SETUP MIC jack on the front panel.
).
Make sure there are no obstacles between the speakers and the microphone.
If you have a tripod, use it to place the microphone so that it's about ear level at your normal listening position. If
you do not have a tripod, use some other object to install the microphone.
Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make
accurate measurement impossible:
! Sofas or other soft surfaces.
! High places such as tabletops and sofa tops.
The Full Auto MCACC display appears once the microphone is connected.
! If you leave the GUI screen for over five minutes, the screen saver will appear.
61
(page 114
) and HDMI output
Microphone
Tripod
2a.Full Auto MCACC
Exit
Return
Speaker System
: 7.2ch/5.2.2ch
EQ Type
: SYMMETRY
MCACC
: M1.MEMORY 1
Dolby Enabled Speaker :
NO
SP to ceiling
:
– – –
Measurement Type :
Expert
START
Basic Setup
- Quick Links:
- Connecting Your Equipment
Hide quick links:
Advertisement
Chapters
Table of Contents
