Hdmi 4K/60P Signal Output Setting; Changing The Channel Level While Listening - Pioneer VSX-90 Operating Instructions Manual

10
Notes
! The subwoofer output depends on the settings you made in
SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
! All speaker systems (except Speaker B connections) are switched off when headphones are connected.
In case of VSX-45
%
Press SP-A/B.
Switches the speaker play on/off.
! You can perform the same operation by pressing SPEAKERS on the front panel.
When you select Speaker B, you can select from:
! SP: A ON – Sound is output from the A-speaker terminals (up to 5 channels (including surround channels),
depending on the source).
! SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals. Multichannel
sources will not be heard.
! SP: A+B ON – Sound is output from the A-speaker terminals (up to 3 channels, depending on the source), the
two speakers connected to the B-speaker terminals, and the subwoofer. The sound from the B-speaker termi-
nals will be the same as the sound from the A-speaker terminals (multichannel sources will be downmixed to 2
channels).
! SP: OFF – No sound is output from the speakers.
Notes
! The subwoofer output depends on the settings you made in
SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
! All speaker systems (except Speaker B connections) are switched off when headphones are connected.
Switching the HDMI output
VSX-90 only
Set which terminal to use when outputting video and audio signals from the HDMI output terminals.
The HDMI OUT 1 terminal is compatible with the Control with HDMI function.
1 Press OUT P..
Use i/j to select 'OUT 1/2'.
2
Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals.
3
Please wait a while when Please wait ... is displayed.
The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.
! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-
nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV's remote
control.
! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2
4 When you're finished, press RETURN.
Manual speaker setup on page 110 . However, if
Manual speaker setup on page 110 . However, if
(page 114 ).

HDMI 4K/60p signal output setting

If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accor-
dance with TV performance.
Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is
not set to MULTI ZONE OFF (page 93 ).
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select an input terminal that you wish to change settings using i/j.
! 4K/60pBD – Sets the signal for the BD IN terminal.
! 4K/60pH1 – Sets the signal for the HDMI IN 1 terminal.
! 4K/60pH2 – Sets the signal for the HDMI IN 2 terminal.
Use k/l to select the signal to set.
4
! 4:4:4 – Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high
quality video images can be enjoyed.
— When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not
be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image.
! 4:2:0 – Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI.
5 When you're finished, press RETURN.
6 Press u STANDBY/ON to switch on the receiver and your TV.
Make sure that the TV's video input is set to this receiver.

Changing the channel level while listening

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor
when setting up a home theater system.
1 Press CH LV..
Use i/j to select the channel you wish to adjust.
2
Adjust the volume using k/l.
3
The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.
4 When you're finished, press RETURN.
Input Volume Absorber
This can be used to correct for the difference in volume between input sources.
1 Switch to the input whose volume you want to adjust.
2 Press CH LV..
Use i/j to select 'ALL'.
3
Adjust the volume using k/l.
4
The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.
5 When you're finished, press RETURN.
92
Using other functions