Page 2
Thank you for buying an innovative product from Fujitsu. Latest information about our products, useful tips, updates etc. is available on our website: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: •...
Page 5
FUJITSU Desktop ESPRIMO D5xx / D7xx / D9xx Operating Manual Your ESPRIMO Ports and operating elements Important notes Getting started Operation Problem solutions and tips System expansions Technical specification Index...
Page 6
Trademarks Fujitsu, the Fujitsu logo and ESPRIMO are registered trademarks of Fujitsu Limited or its subsidiaries in the United States of America and other countries. Kensington, MicroSaver and K-Slot are registered trademarks of ACCO Brands.
"Safety information" • cross-references to an external source, e.g. a web address: For more information, go to "http://www.fujitsu.com/fts" • Names of CDs, DVDs and titles or designations for other materials, e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual indicates a key on the keyboard, e.g:...
4 = Slimline drive insert/eject button reader (external), hard disk (internal) 5 = Slimline drive emergency removal 11 = USB ports 6 = 3½ inch drive status indicator, e.g. 12 = Microphone port SmartCard reader 7 = ON/OFF switch with power indicator Fujitsu...
If the device is brought from a cold environment into the room where it will be used, condensation may occur. Before operating the device, wait until it is absolutely dry and has reached approximately the same temperature as the installation site. Fujitsu...
Use disinfectant wipes to clean the keyboard and the mouse. Energy saving, disposal and recycling Disposal Energysaving Recycling Drivers& UtilitiesDVD User DocumentationDVD You can find information on these subjects in the "Environment and Energy Information" manual or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/"). Fujitsu...
CE nnnn (!) ; nnnn: For digits and exclamation mark (!), see label on the product. You can find more information and declarations of conformity on the Internet at: "http://globalsp.ts.fujitsu.com/sites/certificates". This equipment can be used in the following countries: Belgium...
• Consult the dealer or an experienced radio/TV technician for help. Fujitsu not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Drives and boards If you have received drives or boards with your device, please do not install them until after first-time setup. How to install drives and boards is described in the "System expansions", Page 34 chapter. Fujitsu...
You must remove the feet again to be able to open the device. Verticaloperatingposition Operatingposition,vertical Base feet Sidecover Proceed as follows to operate the device in the vertical operating position with the feet: ► If necessary, disconnect the cables connected to the device. Fujitsu...
Page 21
► Place the feet (3) on the left side of the device so that the pins (2) enter into the corresponding guide openings (4) on the device and the screws rest against the screw holes (6). ► Tighten the screws to secure the feet. ► Stand the device on the feet as shown. Fujitsu...
Russia and the Commonwealth of Independent States (CIS), large parts of Europe, parts of South America, the Middle East, parts of Africa, Hong Kong, India, large parts of South Asia. UK, Ireland, Malaysia, Singapore, parts of Africa China, Australia, New Zealand Fujitsu...
PS/2 keyboard port, purple Mouseport PS/2mouseport Keyboardport DVI-D monitor port DisplayPort DVI-Imonitorport DisplayPort LAN port VGA monitor port, blue Monitorport LANport Serial port Parallel port Serialinterface Parallelport Some of the connected devices require special drivers (see the documentation for the connected device). Fujitsu...
The PS/2 mouse is only detected by the device if you connect the mouse when the device is switched off and then switch the device on again. ► Connect the PS/2 mouse to the PS/2 mouse port of the device. PS/2mouse, Connecting, PS/2mouse, ► Switch your device on again. Fujitsu...
The devices connected to the serial interface require drivers. Your operating system already includes many drivers. If the required drive is missing, install it. The latest drivers are usually available on the Internet or will be supplied on a data carrier. Fujitsu...
Plan a reasonable amount of time for this, as this process must not be interrupted. You may need the licence number for Windows during the installation. You can find the licence number as a label on your device (no longer applies to Windows 8 or higher). Fujitsu...
Help in your operating system. You will find more information on the system, as well as drivers, utilities and updates on the "Drivers & Utilities" DVD and on the Internet at "http://www.fujitsu.com/fts/support". You can find information and help on the Windows operating system functions on the Internet at "http://windows.microsoft.com".
Warning, this could lead to a loss of data! ► Press the ON/OFF switch for at least 4 seconds. The device will switch off. When you next restart the device, error messages may be displayed due to the improper shutdown. Fujitsu...
• The indicator is not lit: The device is switched off. Indicator for optional The indicator lights up when optional components, e.g. SmartCard components, e.g. reader, are accessed. SmartCard reader (depending on the device variant) Fujitsu...
With some keyboards the ON/OFF switch can only be used with an ACPI (Advanced Configuration and Power Management Interface). Otherwise the key is inoperative. The mainboard must support this function. Keys, Keys, Keys, Enter key confirms the highlighted selection. The Enter key is also referred to as the "Return" key. Fujitsu...
In BIOS Setup, you can set the system functions and the hardware configuration of the device. When the PC is delivered, the default entries are valid (see "BIOS Setup" manual or manual for the mainboard). You can customise these settings to your requirements in the BIOS Setup. Fujitsu...
• Key turned towards the closed lock: The device is locked. • Key turned towards the open lock: The device is not locked. Locking the casing ► Turn the key towards the closed lock Fujitsu...
Operation of a SmartCard reader with a RFID reader is not permitted in Taiwan. ► Connect the external SmartCard reader to your system as described in the instructions for the SmartCard reader. SmartCard reader, After the device is switched on, you will be prompted to insert your SmartCard. Fujitsu...
► For further clarification of the problem, contact the Service Desk for your country (see the Service Desk list or visit the Internet at "http://support.ts.fujitsu.com/contact/servicedesk"). When you do this, please have ready the identity number and serial number of your system.
► Restart the system. Incorrect setting for the monitor ► Press while the system is booting. ► Start the system in Safe Mode. ► Set up the monitor as described in the documentation for your operating system and monitor. Fujitsu...
► Make sure you have inserted your SmartCard into the SmartCard reader with the chip facing upwards. ► Check whether the SmartCard you are using is supported. Your SmartCard must comply with the ISO standard 7816-1, -2, -3 and -4. Fujitsu...
You will find the instructions for restoring the contents of the hard disk in the "Recovery Guide" manual. Tips Topic Out of system resources ► Close unnecessary applications. ► Run the applications in a different order. Other manuals Further manuals are provided as PDF files on the "Drivers & Utilities" DVD. Fujitsu...
An update of the BIOS may be required for a system expansion or hardware upgrade. Further information can be found in the BIOS help section or if necessary in the Technical Manual for the mainboard. Fujitsu...
The equipment and tools you use must be free of static charges. • Only touch or hold the boards by the edge or, if present, at the areas marked green (Touch Points). • Never touch pins or conductors on boards fitted with ESDs. Fujitsu...
► Remove any plugged-in wires which are in the way. ► Raise the clip (a), hold it in this position and pull the casing cover in the direction of the arrow (1). ► Lift the casing cover off the casing (2). Fujitsu...
(2) until it reaches a stop. When doing so, make sure that the eye (b) fits into the opening (a). The casing cover will click into place automatically, without any need to move the retaining mechanism. ► Connect the cables to the device. Fujitsu...
1 x non-accessible 3½ inch drive non-accessible 2½ • 2 x non-accessible 2½ inch drives, with inch drives with 3½ 3½ inch adapter inch adapter Upper bay for an Drive plate (screwless) 1 x slimline drive accessible slimline drive Fujitsu...
4 = Accessible 3½ inch drive can be installed 2 = Slimline drive can be installed, non-accessible drives possible under the cover Proceed as follows to replace a drive cover with another drive cover: ► Remove the casing cover (see chapter "Removing the casing cover", Page 36). Fujitsu...
Page 44
System expansions The catches of the drive cover are on the inside. ► First release the two middle catches (a). ► Then release the two side catches (b). ► Remove the drive cover towards the front (1). Fujitsu...
Page 45
(a, b). ► Change the desired drives as required, as described in the corresponding chapter. ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). Fujitsu...
The drive plate is located in the upper bay for the slimline drive. ► Remove the casing cover (see Chapter "Removing the casing cover", Page 36). ► Press the clip in the direction of the arrow (1). ► Remove the drive plate (a) from the upper bay (2). Fujitsu...
Page 47
System expansions ► Secure the drive plate on the slimline drive as shown (3). Fujitsu...
► Connect the cables to the slimline drive and to the mainboard. Make sure the polarity is correct. ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
► Push the slimline drive a few centimetres out of the bay in the direction of the arrow (2). ► Pull the slimline drive completely out of the bay in the direction of the arrow (3). ► Detach the drive plate from the slimline drive (4). Fujitsu...
Page 50
"Changing the drive cover", Page 39). ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
Opening the drive cage ► Remove the casing cover (see chapter "Removing the casing cover", Page 36). ► Press the release (a) in the direction of the arrow (1). ► Fold the drive cage fully open (2) until it locks in place. Fujitsu...
(a) of the drive cage engages again. ► Fold the drive cage in the direction of the arrow (2). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). Fujitsu...
► Fasten the EasyChange rails to the side of the first drive by inserting each pin of the EasyChange rail in the corresponding holes on the drive. In doing so, make sure that the ports on the drive are located at the rear as shown (a). ► Repeat the step for the second drive. Fujitsu...
Page 54
► Slide the drives with the EasyChange rails one after the other into the adapter (1, 2). In doing so, make sure that the component side of the drives point down towards the adapter and the ports on the drives are located at the rear as shown (b). Fujitsu...
EasyChange rails one after the other out of the adapter (2, 3). ► Pull the EasyChange rails off the first drive. ► Repeat the step for the second drive. ► If you no longer need the EasyChange rails, secure them again at their location in the adapter. Fujitsu...
► Fasten the EasyChange rails to the side of the drive or adapter by inserting each pin of the EasyChange rail in the corresponding holes on the drive. In doing so, make sure that the ports on the drive are located at the rear as shown (a). Fujitsu...
Page 57
► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
Page 58
► If you no longer need the EasyChange rails, secure them again in the lower bay. ► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). Fujitsu...
► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
Page 60
► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
► When installing 2.5" HDDs/SSDs or a SmartCard reader: Connect the cables to the drive before you slide it into the bay. On the multicard reader, one end of the cable is already fixed to the reader. ► Slide the drive into the bay (1). Fujitsu...
Page 62
► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
► Fold the drive cage into the closed position again (see chapter "Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the drive accordingly in the BIOS Setup. Fujitsu...
"Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the M.2 module accordingly in the BIOS Setup. Fujitsu...
"Closing the drive cage", Page 48). ► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). If necessary, you must adjust the entry for the M.2 module accordingly in the BIOS Setup. Fujitsu...
Opening the board retaining mechanism ► Remove the casing cover (see Chapter "Removing the casing cover", Page 36). ► Undo the optional safety screw of the board clip, if present. ► Fold out the board retaining mechanism (1). Fujitsu...
► Pull the slot cover out of the slot (2). Do not throw away the slot cover. For cooling, protection against fire and in order to comply with EMC regulations, you must refit the slot cover if you remove the board. Fujitsu...
► If necessary, disconnect the cables which are connected to the board. ► Undo the screw (1, optional). ► Release the board retaining clip (a) where applicable. ► Pull the board out of the slot (2). ► Place the board in suitable packaging. Fujitsu...
"Reattaching the casing cover.", Page 37). If you have installed or removed a board, please check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCI board documentation. Fujitsu...
► Working in the direction of the arrow (1), place the WLAN antennas onto the plug-in positions of the board (2). ► Secure the WLAN antennas by turning in the direction of the arrow (3). ► Align the WLAN antennas as required. Fujitsu...
Removing WLAN antennas ► Undo the WLAN antennas by turning in the direction of the arrow (1). ► Pull the WLAN antennas in the direction of the arrow (3) and away from the plug-in positions of the board (2). Fujitsu...
► Keep the clips (1) pressed and push the sheet metal plate out of the casing from the inside (2). ► Position the serial port on the inside of the device at the appropriate place (3). Fujitsu...
Page 74
► Fit the casing cover onto the casing again (see chapter "Reattaching the casing cover.", Page 37). To remove, carry out the above steps in reverse order. To comply with the electromagnetic compatibility (EMC) regulations, secure the sheet metal plate again at the installation opening. Fujitsu...
► Slightly tilt the cowl and lift it out of the casing (2). In doing so, take care that the pins (a) release from the openings on the casing. ► Undo the screws on the heat sink (3). ► Lift the heat sink out of the casing (4). Fujitsu...
Page 76
System expansions Never operate the device without the heat sink fitted! Reinstall the heat sink before switching on the device. Fujitsu...
► Place the cowl in the casing (3) at a slight angle and pay attention that the pins (b) fit into the openings on the casing as shown. The cowl engages at the location marked "PULL". ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). Fujitsu...
► Upgrade the processor according to the description in the manual for the mainboard. ► Reinstall the heat sink (see "Installing the heat sink", Page 73). ► Fit the casing cover back onto the casing (see Chapter "Reattaching the casing cover.", Page 37). Fujitsu...
► Press the catch in the direction of the arrow (1). The battery jumps out of the holder slightly. ► Remove the battery (2). ► Push the new lithium battery of the identical type into the holder (3) and press it down until it engages. Fujitsu...
Clearance required to ensure adequate ventilation: Without air vents min. 10 mm / 0.39 in With air vents min. 200 mm / 7.87 in The data sheet for this device provides further technical data. The data sheet can be found on our website "http://fujitsu.com/fts/". Fujitsu...
24 Keyboard shortcuts 26 Switching on 24 Keyboard, Device drivers, alphanumeric keypad 26 serial interface 21 connecting 21 Device, cursor keys 26 ports 19 function keys 26 setting up 16 numeric keypad 26 transporting 11–12 port 21 upgrades 34 Fujitsu...
Page 82
Security Lock 28 Mouse port 19 Security measures 28 Mouse, Serial interface 19, 21 connecting 20 Serial interface, connecting devices 21 settings 21 Servicing 34 Note Setup, safety 11 see BIOS Setup 27 Notes Side cover 16 CE marking 13 Fujitsu...
Page 83
USB port, BIOS Setup 27 connecting devices 22 System unit, see Device 12 connecting keyboard 21 connecting the mouse 20 User Documentation DVD 12 Transportation 11–12 Vertical operating position 16 Video workstation 16 Universal Serial Bus 19 Upgrades Mainboard 74 Fujitsu...