Scag Power Equipment STWC Operator's Manual page 43

Section 8
Ref. Part
No. No. Description
1 461656 Cutter Deck Advantage
2 04003-04 Bolt, Carr. 5/16-18 x 1"
3 04019-04 Nut, 3/8-16 Serrated Flange
4 481625-01 Wing Nut, 3/8-16
5 481632 Anti-Scalp Wheel
6 04003-26 Bolt, Carriage 3/8-16 x 4"
7 422478 Bracket, Anti-Scalp Wheel
8 04017-27 Bolt, Serrated Flange 3/8-16 x 1"
9 04043-06 Flatwasher, 5/8" Hardened
10 04021-05 Locknut, 3/8-16 Center Lock
11 461296 Discharge Chute
12 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2", Rear
04001-12 Bolt, Hex Head 5/16-18 x 1-3/4", Front
13 04021-10 Nut, Elastic Stop 5/16-18
14 04020-09 Nut, 5/8-11 UNC
15 45944 Shaft, Roller
16 04001-41 Bolt, Hex Head 5/8-11 x 9-1/2"
17 48038 Roller, Rear
18 04001-154 Bolt, Hex Head 5/16-18 x 4-3/4"
19 04063-08 Key, 1/4 x 1/4 x 2"
20 482718 Spring, Idler
21 04043-04 Flatwasher, 3/8" - .938 x .391 x .105
22 04001-176 Bolt, Hex Head 5/16-18 x 1-3/4" Grade 8
23 04019-03 Nut, Serrated Flange 5/16-18
24 04001-172 Bolt, Hex Head 1/4-20 x 1" Grade 8
25 48100-15 Bushing, .376 ID Oilite
26 04030-03 Lockwasher 5/16"
27 04040-15 Flatwasher 5/16"
28 04001-136 Bolt, 3/8-16 x 1-1/2" Grade 8
29 04021-09 Nut, Elastic Stop 3/8-16
30 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2"
31 04001-54 Bolt, Hex Head 3/8-16 x 3"
32 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Grade 8
33 04110-03 U-Nut, 3/8-16
34 461663 Spindle Assembly
35 43589 Shaft, Spindle
36 481024 Seal Upper
37 481022 Bearing Assembly
38 48114-04 Grease Fitting
39 48677 Valve, Grease Relief
40 43644 Housing, Spindle
41 43312 Spacer, Outside
42 43296 Spacer, Inside
61A" CUTTER DECK
Ref. Part
No. No.
43 481025
44 43297
45 481035
46 43590
47 481708
48 422713
49 48224
50 461174
51 43575
52 423717
53 48926
54 482416
55 04001-14
56 482648
57 423880
58 451240
59 461516
60 04020-16
61 04021-13
62 48763
63 04001-79
64 48114-04
65 482652
66 04001-09
67 482245
68 423792
69 04003-23
70 04041-07
71 04001-51
72 482743
73 482295
74 45944
39
Description
Seal, Lower
Bushing, Bottom
Nut, Special 1-1/16 - 18
Spacer, Spindle
Cutter Blade 21"
Pivot, Idler Base
Bearing
Idler Arm Assy.
Idler Pivot, Short
Belt Cover (61A)
Hub, Tapered 1-1/8" Bore
Pulley, Idler 5.0"
Bolt, Hex Head 1/4-20 x 1"
Pulley, 5.95 Dia. Tapered Bore
Turbo Baffle, Bolt On
Push Arm Shaft
Push Arm (Includes 64,60,62)
Nut, 5/8-18 UNF
Nut, Elastic Stop 5/8-11
Rod End, 5/8 Male RH Thread
Bolt, Hex Head 5/8-11 x 4-1/2"
Grease Fitting, 90 Degree
Belt, Cutter Deck Drive (61A)
Bolt, Hex Head 5/16-18 x 1"
Spring, Discharge Chute
Baffle Weldment, 61A
Bolt, Carriage 3/8-16 x 1"
Flatwasher, 3/8-.391 x .938 x .105
Bolt, Hex Head 3/8-16 x 3-3/4"
Pulley, Idler 5.0" OD
Wheel, Anti Scalp
Roller Shaft