Painting - Titan 0508074A Owner's Manual

Priming with Hopper assembly
1. Turn the pressure control knob counterclockwise to its lowest
pressure setting.
2. Remove the paint hopper cover and fill the paint hopper with
material or place the suction set into a bucket of material.
3. Turn the PRIME/SPRAY valve to PRIME.
4. Move the motor ON/OFF switch to ON.
5. Turn the pressure control knob clockwise to between half and
full pressure. Let the unit prime 1 to 2 minutes after material
begins to flow through the return tube.
IMPOrTaNT: always reduce the pressure to zero before
changing the position of the PrIME/SPray valve. Failure to do
so may cause damage to the paint pump diaphragm.
IMPOrTaNT: If the pressure control knob is reduced to zero
and the PrIME/SPray valve is still on SPray while the sprayer is
operating, there will be high pressure in the hose and spray gun
until the PrIME/SPray valve is turned to PrIME or until the spray
gun is triggered to relieve the pressure.
Priming with Optional Suction Set
1. Place the suction set into a container of paint.
2. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
IMPOrTaNT: always reduce the pressure to zero by triggering
the spray gun before changing the position of the PrIME/SPray
valve. Failure to do so may cause damage to the paint pump
diaphragm.
3. Turn the PRIME/SPRAY valve to PRIME.
PRIME/SPRAY
Pressure
Control Knob
4. Move the pump ON/OFF switch to the ON position.
5. Turn the pressure control knob clockwise to between half
and full pressure. Let the unit prime 1 to 2 minutes after paint
begins to flow through the return hose until no bubbles are
present.
6. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
7. Move the pump ON/OFF switch to the OFF position.
IMPOrTaNT: If the pressure control knob is reduced to zero
and the PrIME/SPray valve is still on SPray while the pump is
operating, there will be high pressure in the hose and spray gun
until the PrIME/SPray valve is turned to PrIME or until the spray
gun is triggered to relieve the pressure.
English
Valve

Painting

The AirCoat spray system has two different painting modes. The
AirCoat mode is used for fine finish work with low to medium
viscosity materials (oil, stains, lacquers, etc...). The airless mode is
used for general painting with high viscosity materials (latex).
Painting in aircoat Mode
Use the AirCoat mode for low-pressure fine finish work
(recommended pump pressure up to 1000 PSI).
1. Make sure that the airless spray hose is free of kinks and clear
of objects with sharp cutting edges.
2. Turn the pressure control knob counterclockwise to its lowest
setting.
3. Turn the compressor air pressure regulator counterclockwise
to its lowest setting.
4. Move the compressor ON/OFF switch to the ON position.
5. Move the pump ON/OFF switch to the ON position.
Pump ON/OFF
6. Turn the PRIME/SPRAY valve to SPRAY.
7. Turn the pressure control knob clockwise until the material
pressure gauge reads 400 PSI. The paint hose should stiffen as
paint begins to flow through it.
8. Turn the air pressure regulator clockwise until the air pressure
gauge reads 20 PSI.
Air Pressure
Regulator
9. Unlock the spray gun trigger.
10. Trigger the spray gun to bleed air out of the material hose.
11. When material reaches the spray tip, spray a test area to check
the spray pattern.
12. Adjust the spray pattern to the desired size and atomization.
a.
Use the pressure control knob to control the flow of paint to the
gun.
b.
Use the air pressure regulator to control the amount of atomization
air available to the gun.
c.
Use the pattern adjustment knob on the gun to fine tune the spray
pattern.
NOTE: refer to the spray gun Owner's Manual for
information on the operation of the gun.
6
Switch
Compressor
ON/OFF Switch
Air Air
Pressure Pressure
Gauge Gauge
Material Material
Pressure Pressure
Gauge Gauge
© Titan Tool. All rights reserved.