Blodgett BCX-14G Installation Operation & Maintenance page 36

Operation
MenuSelect™ Control for Model CNVX-14
PROGRAMMING A PRODUCT RECIPE
NOTE: The control can hold 99 recipes. Each recipe
may have up to 6 cooking stages.
1. Turn the dial to highlight the name of the product to
be programmed. Press the center of the dial to select
the product.
2. The display reads PRODUCT NAME: STAGE 1.
Press the center of the dial to select the stage.
3. Rotate the dial, or use the alpha/numeric keypad to
enter the desired bake time. Press the center of the
dial to set the bake time.
NOTE: Time is set in one minute increments using
the dial. To set time in less than one minute
increments use the alpha/numeric keypad.
4. Rotate the dial, or use the alpha/numeric keypad to
enter the desired cook temperature. Press the center
of the dial to set the bake temperature.
NOTE: Temperature is set in 5 degree increments
using the dial. To set time in less than 5
degree increments use the alpha/numeric
keypad.
NOTE: Retherm has a temperature limit of 250-
300ºF.
5. Rotate the dial to select the desired fan speed.
Choose from gentle, low, high or turbo. Press the
center of the dial to set the fan speed.
6. Rotate the dial to select the fan rotation cycle. Choose
between manual or auto.
NOTE: This is the length of time the fan will rotate
in one direction before reversing.
If manual is selected, rotate the dial or use the alpha/
numeric keypad to enter the desired fan cycle. Press
the dial to set the fan cycle.
If auto is selected, the program will use the default
fan cycle setting. The default is set through the Man-
ager Programming.
7. Rotate the dial to set the vent position. Choose be-
tween OPEN or CLOSE. Press the center of the dial
to set the vent position.
8. Use the dial to scroll down to PRODUCT NAME:
STAGE 2. Press the center of the dial to select stage
2.
9. Repeat steps 2-9 for all remaining stages.
10. When all stages have been programmed, press the
PROGRAM KEY (11). To save the programming, use
the dial to scroll to YES. Press the center of the dial.
The control exits the program mode.
USING THE USB PORT
1. With the power on, remove the cover of the USB port
(18) and insert the USB drive.
2. Press the MAINTENANCE KEY (13).
3. Turn the dial to highlight MANAGER PROGRAM.
Press the center of the dial to select.
4. Turn the dial to highlight either COPY RECIPE FROM
USB or COPY RECIPE TO USB, then press the cen-
ter of the dial to select.
5. When the transfer is complete, press any key to re-
turn to the menu.
6. Turn the dial to highlight EXIT. Press the center of
the dial to select. The display returns to the previous
menu.
7. Turn the dial to highlight EXIT. Press the center of the
dial to select.
MANAGER PROGRAMMING
Entering the Manager Program Mode
1. Press the MAINTENANCE KEY (13). If the control
is password protected, the display reads ENTER
CODE. Use the alpha/numeric keypad to enter the
manager passcode 3124, then press the center of the
dial to enter the program mode.
2. Turn the dial to highlight OVEN SETUP. Press the
center of the dial to select the product.
Programming Auto Start
NOTE: The Auto Start function enables the oven to turn
on at a programmed time of day and preheat to
a programmed temperature.
1. Turn the dial to highlight AUTO START. Press the
center of the dial to select.
2. Turn the dial to select either ON or OFF. Press the
center of the dial to select.
If ON is selected, the display reads AUTO START 24
HOUR TIME 00:00. Turn the dial to enter the time you
would like the oven to begin preheating. Press the
center of the dial to select.
The display reads AUTO START TEMP XXX. Turn
the dial to enter the desired preheat temperature.
Press the center of the dial to select.
32