Important Notes For The Individual Applications; End Operation And Remove Bowl; The Blender; Blender Use Instructions - Profi Cook PC-KM 1025 Instruction Manual

Important notes for the individual applications

CAUTION:
• Do not chop up hard food such as coffee beans, nutmeg, turmeric or
large pieces of cooking chocolate! The blade could be damaged as a
result!
• Do not exceed the quantities and operating times listed in the table.
• Always fit the kneading / stirring attachment or the dicing blade
into the bowl before you add the ingredients. Press the attachment to
the bottom of the bowl.
If you are kneading heavy dough, do not add all the ingredients into
•
the working bowl all at once. Only start the kneading process with
flower, sugar, and eggs. Slowly add liquids through the feed shaft dur-
ing the kneading process.
• First, cut the food that you want to chop into small pieces.
• If ingredients are stuck to the kneading/ stirring tool or the dicing blade
or if they settle on the inside wall of the bowl, then proceed as follows:
1. Turn off the appliance. Wait for the attachment to stop running.
2. Remove the lid from the bowl.
3. Use the dough scraper to remove the ingredients from the at-
tachment or from the inside wall of the bowl.
• If you whip the egg whites, ensure that the bowl and the whisk are
dry and completely free of grease. The egg white should be at room
temperature.
• To grate chocolate, only use the dicing blade, not a grating blade. The
chocolate must be well chilled.
• When you cut up hard cheese or chocolate, do not let the appliance
run too long. These ingredients can melt through the warming of the
appliance and may become lumpy.
When chopping and grating, fill the ingredients into the feed shaft.
•
Use the pusher to push the food down into the filler hole. Do not apply
too much pressure to the pusher.
• The pusher consists of two parts. If you twist and pull off the top part,
you will find a smaller feed shaft. Then, press the ingredients down-
wards with the inner pusher.
• If you use the appliance as a citrus press, please observe the follow-
ing:
- The press cone will start to turn as soon as you turn on the appliance.
- Only turn on the appliance with the control knob. Only work at the
lowest speed setting.
- Cut the citrus fruits in half. Press half of the fruit onto the press cone.
- Interrupt the process from time to time to remove the pulp from the
filter sieve.
- Turn off the appliance before you remove the bowl with the filter sieve
and the press cone.
- Chill the citrus juices for no longer than one day.
- Never store the citrus juice in a metal container. The acid of the juice
will corrode the metal surface. Metal ions will form that spoil the taste
of the juice.

End Operation and Remove Bowl

1. Turn the appliance off. Wait until the attachment stops running.
2. Disconnect the mains plug.
3. Turn the lid or the filter sieve anticlockwise from the lock to open the
bowl.
4. Remove the attachment.
5. Twist the working bowl out of the lock by turning anticlockwise. Lift the
bowl upwards away from the motor housing. Watch out for the guide
pin.
6. Use the dough scraper to remove the contents of the bowl.
7. Clean all the parts used as described under "cleaning".

The Blender

Blender Use Instructions

WARNING: The knife in the blender is sharp!
• Never reach with your hands into the assembled mixing container!
• Handle the blender knife with great care! Risk of injury, especially when
removing the knife from the mixing container, emptying and cleaning the
mixing container!
• Do not pour liquid ingredients hotter than 60°C into the mixing container!
Danger of burns!
CAUTION:
• Do not place hard ingredients such as nuts or coffee beans in the mix-
ing container.
• The knife in the mixing container is not suitable for crushing ice cubes
only.
RECOMMENDATION:
• When preparing drinks with crushed ice only add the ice cubes dur-
ing mixing. The ice cubes will be crushed during mixing. Only use the
TURBO button for that purpose.
• Do not use the blender without ingredients!
• Do not exceed the maximum capacity (1500 ml) as indicated on the mix-
ing container!
• If you are using lightly foaming liquids (e.g. milk), fill a pour it into the
blender jug to a maximum of 900 ml.
• Only turn on the mixer with the lid and the fitted cap. The lid will sit tightly
on the blender jug when it has audibly clicked into place with a small twist
clockwise.
• Do not remove the lid during operation! Wait until the blade comes to a
stop before you open the lid.
• Should you not be satisfied with the mixing results, proceed as follows:
1. Turn off the appliance.
2. Remove the lid from the blender jug.
3. Loosen any stuck-on ingredients with the dough scraper. Stir the
ingredients with the dough scraper. Maintain a distance of at least
approx. 2 cm to the blade while doing so.
4. Remove some of the contents. Process smaller quantities or add
some liquid.

Mixing Container Assembly

For this, please also refer to figures 6 and 7 on page 6.
1. Fit the gasket into the knife block.
2. Screw the blender jug onto the knife block.
3. Fig. 7: Fit the pre-assembled blender jug onto the motor housing so that
the marking (a) on the lower edge of the knife block points to the marking
(b) of the motor housing. Turn the blender jug clockwise until it audibly
clicks into place. The marking (a) on the knife block and the marking (c)
on the motor housing must be aligned exactly above each other.
CAUTION:
• Never forget to place the sealing ring on the knife assembly; otherwise
the mixing container will leak.
• Do not attach the threaded coupling askew.

Preparation

1. Cut all ingredients in small pieces.
2. Fill the ingredients into the mixing container. Observe the maximum
capacity.
3. Fit the lid onto the blender jug. Tighten it until it audibly clicks into
place.
4. Close the lid with the stopper (17).
41