Tail Boom / 尾管組裝 - THUNDER TIGER miti titan v2 Instruction Manual

TAIL BOOM / 尾管組裝
Bag J
No. Material No. Description
BK2628 DRIVE SHAFT SET, d2xD4x359L
1*
BK1073 BELT MXL-3T（413T）
2 BK1004-1 TAIL BOOM 356MMXø14
3 HME3-2.5B SET SCREW M3x2.5
4 BK1584 T-PIN d2x12
5 BK1569 TORQUE TUBE END
BV2612 METAL TAIL UNIT HOUSING
6*
BK1872 METAL TAIL UNIT
7 BK1567 BEVEL GEAR, 11T
TORQUE-TUBE VERSION
HMD2-5B
Flat Head Phillips Screw, M2x5
M2x5
平頭十字螺絲
HSA2-6
Button Head Socket Screw, M2x6
M2x6
半圓頭內六角螺絲
The slot is toward
upper side.
尾管上缺口朝上
(5)
BELT-DRIVEN VERSION
Insert the Belt into the Tail Boom.
First tape the belt & insert the end
of the belt as shown, and not twist
the belt.
將皮帶穿過尾管。用膠帶將皮帶尾端貼
合可使皮帶較容易穿過尾管；並請勿扭
轉皮帶。
The slot is toward upper side.
尾管上缺口朝上
(1*)
Tape / 膠帶
名稱
, d2xD4x359L
驅動軸
MXL-3t（413T）
皮帶
356mmxø14
尾管
M3x2.5
無頭內六角螺絲
d2x12
T型銷
驅動軸接頭
軸傳金屬尾座
金屬尾座
, 11T
傘齒輪
*
available depending on the kit you purchased.
使用零件因購買套件有所不同。
Add a drop of thin CA glue on the Drive
Shaft next to where the Bearing should
be, and then slide it over the position
quickly; the distance from the end of
shaft is approx. 180mm / 7.08"
在尾傳動軸上軸承固定位置前方，塗抹少量
快乾膠，迅速滑動軸承至定位固定；該定位
大約距離傳動接頭
CA
180mm / 7.08"處
(2)
(3)
(12)
(13)
(4)
(3)
T22
(6*)
(4)
(2)
Qty No. Material No. Description
1 BV1576 TAIL ROTOR SHAFT
8*
1 BV0973A MATEL TAIL ROTOR SHAFT SET
1 BV2613 METAL TAIL SIDE COVER SET
9*
4 BV1874 METAL TAIL SIDE COVER- L
2 10 HSA3-6 BUTTON HEAD SOCKET SCREW, M3x6
2 11 HSA2-6 BUTTON HEAD SOCKET SCREW, M2x6
1
12 BK1578 SHOCK-AXIS RUBBER WASHER, d8xD11x6
1
13 HMV840ZZY BERING, d8xD8xW3
1
14 BK1875 TAIL UNIT SPACER
15 HMD2-5B FLAT HEAD PHILLIPS SCREW, M2X5
Secure all screws shown on this page with
a drop of thredlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
(11)
(6*)
180mm
T22
(8)
T22
90°
-14-
名稱
尾旋翼橫軸組
尾旋翼軸組
軸傳金屬尾座側蓋
金屬尾座側蓋組
半圓頭內六角螺絲
半圓頭內六角螺絲
軸傳避震墊圈, d8xD11x6
滾珠軸承, d8xD8xW3
尾座支柱
平頭十字螺絲
(7)
(8*)
(11)
T22
(1*)
Apply some silicon oil or Vaseline
onto the rubber surface for easy
install into the tail boom.
塗抹些許矽膠油脂或凡士林於橡膠套
表面上，將尾驅動軸組裝入尾管時，
會較為容易。
Apply grease
使用潤滑油膏(黃油)
(15)
T22
(14)
(8*)
(6*)
(11)
T22
(9*)
The slot o n the boom is
right angle to the Metal
Tail Rotor Shaft. (View
from nose to tail)
請注意，尾管上缺口應與尾
旋翼軸呈直角狀態。
（由機首向機尾方向看）
Qty
1
1
1
1
-
左
2
M3x6
3
M2x6
1
1
1
6
M2x5
(9*)
(10)
T22
T22
(15)
T22