Bosch PSB 570 RE Original Instructions Manual page 11

OBJ_BUCH-1752-001.book Page 11 Monday, July 23, 2012 3:11 PM
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Depth stop*
2 Front sleeve
3 Rear sleeve
4 Keyless chuck
5 Button for depth stop adjustment *
6 "Drilling/Impact Drilling" selector switch
7 Lock-on button for On/Off switch
8 Rotational direction switch
9 On/Off switch
10 Auxiliary handle (insulated gripping surface) *
11 Wing bolt for adjustment of auxiliary handle *
12 Handle (insulated gripping surface)
13 Universal bit holder*
14 Screwdriver bit*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Impact Drill
Article number
Rated power input
Output power
No-load speed
Rated speed
Impact rate
Rated torque
Torque at max. output power
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Drilling into metal: a =4.0 m/s , K=1.5 m/s
h
Bosch Power Tools
Impact drilling into concrete: a
Screwdriving without impact: a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
PSB 570 RE
according to the provisions of the directives 2011/65/EU,
3 603 A27 0.. 2004/108/EC, 2006/42/EC.
W 570 Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
W 260
D-70745 Leinfelden-Echterdingen
-1
min 50 – 3000
Dr. Egbert Schneider
-1
min 2400
Senior Vice President
-1
min 33000
Engineering
Nm 1.1
Nm 7.5
Robert Bosch GmbH, Power Tools Division
mm 43
D-70745 Leinfelden-Echterdingen
16.07.2012
mm 10
mm 8 Assembly
mm 25
Before any work on the machine itself, pull the mains
mm 2 – 13
plug.
kg 1.6
Auxiliary Handle (see figure A)
/II
Operate your machine only with the auxiliary handle
10.
Before any work, make sure that the wing bolt 11 is
firmly tightened. Loss of control can cause personal inju-
ry.
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 11 in
anticlockwise direction and set the auxiliary handle 10 to the
required position. Then tighten the wing bolt 11 again in
clockwise direction.
2
,
English | 11
2 2
=33 m/s , K=3.5 m/s ,
h
2 2
<2.5 m/s , K=1.5 m/s .
h
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
2 609 006 498 | (23.7.12)