User Interface Devices - Honeywell Intelliguard 9000 Installation Instructions Manual

Intelliguard 9000 Specification Data. Follow the instructions
included with each device for mounting and connecting to the
system.

User Interface Devices

AREA KEYPADS (KID)
A KID allows a user to arm or disarm. Fig. 15 shows an area
keypad.
FLASHING GREEN = ENTER SECOND ID AND CODE
POINT STATUS (4 LEDs)
AREA STATUS
FLASHING RED = EXIT DELAY
KID UNIT
ASSEMBLY
8003-220
ID-CODE
DOOR
TB-1
1 2 3 4
TRBL.
LED
IDENTIFICATION
CARD SLOT
(FITS UNDER WINDOWS OF KEYPAD).
CARD PROVIDES PREDEFINED OR
CUSTOM TEXT FOR POINT STATUS LEDS.
NOTE: THE LED IDENTIFICATION CARD (7003-174) IS INCLUDED
WITH THE UNIT BETWEEN THE P.C.B. AND KEYPAD SUPPORT.
Fig. 15. Area Keypad.
NOTE: TB1-1 and TB1-2 connect to 12 Vdc whereas TB1-3
(TXRX-) and TB1-4 (TXRX+) connect to CU COM 1
or 2, but not both.
1. Remove the KID cover at the selected mounting loca-
tion.
2. Remove the LED identification card located on the left
side of the unit between the printed circuit board and the
keypad. (Store in a safe place).
IMPORTANT
Touch a grounded object to ensure you are not elec-
trostatically charged before handling the circuit
board.
3. Carefully pry up the left side of the support/keypad
assembly first and then lift up the right side. Notice how
the keypad cable is folded.
ID CODE
RED = ENTER ID
YELLOW = ENTER CODE
GREEN = VALID
OFF = ALARM RESTORED/CLEAR
RED = POINT IN ALARM
OFF = SEE POINT STATUS LEDS
GREEN = READY TO ARM
RED = ARMED
KID P.C.B. ASSEMBLY
8003-218
1 2 3
5
4 6
7 8 9
0
RS-485
– +
– +
12 VDC CU COM
M16113C
4. Lift up the assembly from the left side and disconnect
the keypad from the connector on the right side.
5. Place the assembly in a safe location.
6. Avoid touching any of the circuits or terminals.
7. Mount the KID on the wall using four No. 6 round or pan
head screws. (It is not necessary to remove the printed
circuit board assembly because access holes are pro-
vided in the top left and right corners.)
NOTE: Feed the required cables into the KID base by using
the two holes in the base wiring channel, or remove
the knockouts on either end of the wiring channel to
pass the cables through the openings.
8. Connect the wires to the KID as shown in Fig. 15.
9. Reinstall the support/keypad assembly by reconnecting
the cable onto the angled connector located on the right
side of the printed circuit board assembly.
10. Make sure the connectors are properly aligned.
11. Carefully fold (do not crease or twist) the keypad cable
and align the keypad assembly mounting holes with the
four standoffs and snap into place.
12. Verify that the LEDs align with the slots in the support
(or the assembly will bend and not seat properly on the
standoffs).
13. Detach one of the LED identification strips (removed
from the card in step 2), or use a blank strip to enter
custom text and insert it into the slot on the left side of
the keypad. See. Fig 15. The text will be visible through
the keypad windows beside the point status LEDs.
14. Replace the KID cover.
15. Repeat steps 1 through 14 for each KID.
16. When installation is complete and power is applied,
learn the KID.
NOTE: Steps 16a. through 16k. may be replaced by using
the PRO 9000 software. See the Commission sec-
tion, steps 1a. through 1c., for more information.
a. From the CC2, select MODE.
b. Enter the technician ID and code.
c. Press 5 to select CONFIGURATION mode.
.
d. Press
e. Press 1 to select LEARN mode.
.
f. Press
g. Press 2 to learn devices with serial numbers.
.
h. Press
NOTE: The CC2 displays Searching and all the LEDs on
the KID blink simultaneously. If the KID had previ-
ously been learned, the LEDs would blink and turn
off as soon as the I9000 established communication
(time varies before this happens depending on the
number of devices connected to the system).
i. Press any key to learn the KID and turn off the
LEDs.
j. Press the ACCEPT key from the CC2. The I9000
exits the learning mode and displays the total num-
ber of devices known by the system including the
KIDs.
k. From the CC2, exit from the CONFIGURATION
menu for changes to become effective.
15
INTELLIGUARD 9000™
74-3047—1